Marshall Electronics V-R902DLW User manual

Marshall Electronics
Model V-R902DLW
Dual 9” Desktop and Rack Mount Dual Link / Waveform Monitor
Operating Instructions
Edition 2 Revision 0W

2
Page intentionally left blank

3
Table of Contents
Installation and Initial Setup ------------------------------------------------------------------------------------------------------5
Top and Front Panel Features ----------------------------------------------------------------------------------------------------7
Rear Panel Features-----------------------------------------------------------------------------------------------------------------8
Compatible Input Formats---------------------------------------------------------------------------------------------------------9
MAIN MENU AND NAVIGATION------------------------------------------------------------------------------------------------ 10
Using the RotoMenu knob ------------------------------------------------------------------------------------------------------ 10
Marker Setup Submenu ......................................................................................................................................................................10
Video Config Submenu ........................................................................................................................................................................13
Audio Config Submenu........................................................................................................................................................................16
Color Config Submenu.........................................................................................................................................................................17
System Config Submenu......................................................................................................................................................................17
OSD Config Submenu ..........................................................................................................................................................................19
IMD Config Submenu ..........................................................................................................................................................................22
IMD Fixed Config Submenu .................................................................................................................................................................24
Closed Captioning Submenu ...............................................................................................................................................................25
Wave/Vector Submenu .......................................................................................................................................................................26
Ancillary Submenu...............................................................................................................................................................................28
Service Submenu .................................................................................................................................................................................29
Specifications----------------------------------------------------------------------------------------------------------------------- 31
Dimensions-------------------------------------------------------------------------------------------------------------------------- 32
Maintenance------------------------------------------------------------------------------------------------------------------------ 34
Warranty ---------------------------------------------------------------------------------------------------------------------------- 34

4
Page intentionally left blank

5
Installation and Initial Setup
■Unpacking
Carefully unpack the V-R902DLW monitor and verify that the following items are included:
• V-R902DLW Monitor
• V-PS12V-5A-2 Power Supply
• Operating Instructions
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage, immediately
contact Marshall Electronics at [phone]. If you are not located within the continental United States, call +1 (310) 333-
0606.
■Installation
The V-R902DLW can be mounted in any standard EIA 19” equipment rack. The attached rack ears can be angled to provide the
user control over the viewing angle. Adequate ventilation is required when installed to prevent possible damage to the
monitor’s internal components. Please see the Dimensions section for more information.
■Connections, Power-On and Initial Setup
Plug the power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the Power connector to the back of the monitor.
Connect the required cables for video signal input and output. (Power must be applied to the V-R902DLW for the active loop-
though output to be activated.) The monitor defaults to ‘ON’ when power is supplied. Video will automatically be detected and
displayed on the screen.

6
Page intentionally left blank

7
Top and Front Panel Features
Power Button
Use the power button to toggle between ON and STANDBY
modes. The LED on the POWER button will illuminate fully
when the unit is in STANDBY mode. The LED will dim when
the unit is ON.
Input Select Buttons (SDI 1, SDI 2, DVI)
Use the SDI 1, SDI2 and DVI buttons to select the
corresponding video input. Accepted video standards are
automatically detected.
Layout Button
Use the Layout button to switch between the four available
layouts on the monitor. See the Layouts section for more
information the available layouts.
User-Definable Function Buttons
Four user-definable function buttons can be used for direct
access to various settings. Functions are assigned using the on-
screen menu.
RotoMenu™Knob
The RotoMenu™knob allows for accessing and navigating the
main menu using only a single knob.
Image Adjustment Knobs
Use the image adjustment knobs to adjust color brightness,
color-saturation, tint, and contrast of the image. The status of
each image adjustment parameter is shown on the bottom left
of the screen, with values ranging from 0 to 100. Default value
is 50.
LED Tally
Three LED tally lights (yellow, red, green) are available above
the screen.
Headphone Output
The 1/8” jack on the monitor takes two channels of embedded
SDI audio and provides a Headphone audio signal. Volume can
be adjusted via the RotoMenu knob or in the Audio
Configuration submenu.

8
Rear Panel Features
SDI Inputs / Outputs and DVI-I Input
The V-R902DLW has two 3G-SDI inputs and two active loop-
through outputs. SDI 1 and SDI 2 can be used simultaneously
to display Dual Link SDI signals. The DVI-I Input Connector
includes EDID and HDCP for connection to computers, DVD
Players, Rasterizers, etc.
Power Input
Connect the 2-pin Twist-Lock power input connector here.
Power should only be supplied from the included power
supply.
IMPORTANT: If using a power source other than the included
power supply, damage may result. Please use the pin out
diagram in the Specifications section.
Tally Input / GPI Connector
The LED tally can be activated via the HD-15 connector by
connecting the corresponding pin to ground. A variety of
external devices can be used to perform the contact closure.
The HD-15 connector can also be used as a GPI port by
changing the settings in the On Screen Menu. No additional
power should be supplied to the HD-15 port.
RS-422/RS-485 Serial Interface
The RS-422/485 ports are used to remotely control the IMD or
all DLW features. (Note: Connector/pin-out may need to be
adapted depending on the protocol and controlling device
used). Only one connection to either port is needed to control
the monitors. The second port can be used to loop multiple
monitors in the same bus.
Line Out
The Line Out 1/8” jack on the back of the monitor takes two
channels of embedded SDI audio and provides a Line Level
audio signal. See the Audio Configuration section for
instructions on how to select the two audio channels.

9
Compatible Input Formats
The following video standards are supported by the V-R902DLW:
SDI Inputs
525i, 625i/50
720p/29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1035i/59.94, 60
1080i/ 50, 59.94, 60
3G – Level A and Level B
YCbCr, YCbCr+A, RGB, RGB+A
1080p/ 60, 59.94, 50
1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF
1080i/ 60, 59.94, 50
3G – Level A and Level B
YCbCr, YCbCr+A, RGB, RGB+A
1080p/ 60, 59.94, 50
1080p/ 30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 25sF, 24sF, 23.98sF
1080i/ 60, 59.94, 50
Dual Link
YCbCr, YCbCr+A, RGB, RGB+A
1080p/ 60, 59.94, 50
1080i/ 60, 59.94, 50
1080p/30, 29.97, 25, 24, 23.98, 30sF, 29.97sF, 24sF, 23.98sF
2K
1080p/ 30, 29.97, 25, 24, 23.98
DVI-I Input (DVI-Analog and DVI-Digital)
640 x 480/ 60
800 x 600/ 60
1024 x 768/ 60
1280 x 1024/ 60
1600 x 1200/ 60
Video standards (HDMI or YPbPr over DVI connector)
720p/50, 59.94, 60
1080i/50, 59.94, 60
1080p/23.98, 24, 25, 29.97, 30, 50, 59.94, 60

10
MAIN MENU AND NAVIGATION
Access and navigate the main menu using the RotoMenu™knob:
Using the RotoMenu knob
• Press the RotoMenu™knob to enter the main menu.
• Rotate the knob to scroll up or down in the main menu or each submenu.
• Press the RotoMenu™knob to enter a submenu or choose a setting.
• To return to main menu from submenu, select ‘Back’ and press the RotoMenu™.
The menu timeout can be set in the OSD Timeout section of the OSD Config submenu.
Marker Setup Submenu
Use the Marker Setup submenu to select various on-screen markers, adjust the Marker Background, or toggle the Center Marker ON
or OFF.
Main Menu
Marker Setup Submenu