Marshall Electronics V-LCD70W-SH User manual

Model No. V-LCD70W-SH
7” 3G-SDI / HDMI Professional Camera-Top Monitor
Operating Instructions
Marshall Electronics Broadcast A/V Division
Ver. 1.0

2Marshall Electronics
V-LCD70W-SH Operation Manual
Table of Contents
1. Installation & Initial Setup...........................................……....................... 3
2. Top & Front Panel Features ...................................................................... 4
3. Rear Panel Features................................................................................. 5
4. Compatible Input Formats ....................................................................... 6
5. Main Menu & Navigation.................................................…...................... 7
6. Specifications........................................................................................... 10
7. Sun Hood Installation………................................................…................. 11
8. Included Accessories………................................................…................. 11
9. Troubleshooting………................................................…...... ................... 11
10. Maintenance………................................................…...... ........................ 12
11. Warranty………................................................…..................................... 13
IMPORTANT SAFETY INSTRUCTIONS:
• Please do not place the display screen towards the ground to avoid scratching the LCD surface.
• Please avoid heavy impact.
• Please do NOT use chemical solutions to clean this product. Simply wipe with a clean soft cloth to
maintain the brightness of the surface.
• Please do not block any vent hole.
• Please follow the instructions and trouble-shooting to adjust the product.
• Internal adjustments or repairs must be performed by a qualied technician.
The V-LCD70W-SH has been tested for conformance to safety regulations
and requirements, and has been certied for international use. However, like
all electronic equipment, the V-LCD70W-SH should be used with care. Please
read and follow the safety instructions to protect yourself from possible injury
and to minimize the risk of damage to the unit.

3
www.LCDracks.com
Marshall Electronics
1. Installation & Initial Setup
Unpacking
Carefully unpack the V-LCD70W-SH monitor and verify that the following items are included:
• V-LCD70W-SH Monitor
• 12V-2A Power Supply
• Operating Instructions
• Sun Hood
Supplied mounting screws:
• KM2.5*6MM x4 (used for Marshall base plate Part# 0032-1308A)
• PM2.5*12MM x4 (used for Marshall VM mount Part# 0032-1301A for IDX battery)
• PM4*6MM x4 (used for VESA mount screw holes)
Inspect the unit for any physical damage that may have occurred during shipping. Should there be
any damage, immediately contact Marshall Electronics at [phone].
If you are not located within the continental United States, call [phone].
Connections, Power-On and Initial Setup
a. Plug the power supply into an AC power source (100-240 V @ 50/60 Hz).
b. Attach the Power connector to the back of the monitor.
c. Connect the required cables for video signal input and output.
d. Press the Power button to turn the unit on, then press Input to select either HDMI or SDI source
as derived.

4Marshall Electronics
V-LCD70W-SH Operation Manual
2. Top & Front Panel Features
1
2
3
4
6
7
5
F1~F3 user-dened function buttons.
Shortcut: Long press on any function button (3-5 seconds) pops up menu for setting.
Press Up/Down buttons to choose settings, then press the Menu button to conrm the
selection.
Functions of F1-F3 buttons can be set to:
Center Marker, Aspect Marker, Check Field, Underscan, Scan, Aspect, DSLR, Freeze,
H/V delay, Peaking, False Color, Exposure, Histogram, Level Meter, Waveform and Time
Code.
Default function: F1: Waveform F2: Scan F3: Aspect
POWER button
Battery indicator light. ( Red light - OFF mode, green light - Operating mode).
INPUT: Switch between SDI and HDMI.
▲/▼ Select option in the menu. Increase or decrease the option value.
Menu: Select button
Headphone jack. Accepts standard 3.5mm mini-phone plug.
2
3
4
5
6
7
1

5
www.LCDracks.com
Marshall Electronics
3. Rear Panel Features
1. Serial Digital “BNC” Connectors
SDI input and loop out. Conversion is possible between HDMI and SDI inputs. See System
section of menu. Compatible with SDI, HD SDI and 3G SDI inputs. Embedded audio may be
monitored at the Headphone jack and visually monitored on-screen.
2. TALLY Connector
The tally light above each monitor is controlled by grounding the appropriate pin on the Tally
connector as shown in the table.
Caution: External power should never be applied to the Tally connector.
3. HDMI Digital Video Connectors
HDMI input and loop out. Conversion is possible between HDMI and SDI inputs. See System
section of menu. Embedded audio may be monitored at the Headphone jack and visually
monitored on-screen.
4. Power Connector. DC power input.
21 3
4

6Marshall Electronics
V-LCD70W-SH Operation Manual
4. Compatible Input Formats
3G-HD-SDI Input
525i/59.94, 60, 625i/50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080i/50, 59.94, 60
3G – Level A
1080p/ 60, 59.94, 50
HDMI Input
480p59.94, 576p50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080p/ 50, 59.94, 60
1080i/50, 59.94, 60
HDMI / SDI Conversions
480i59.94, 576i50
720p/25, 29.97, 30, 50, 59.94, 60
1080p/23.98, 23.98sF, 24, 24sF, 25, 29.97, 30
1080p/ 50, 59.94, 60
1080i/50, 59.94, 60

7
www.LCDracks.com
Marshall Electronics
5. Main Menu & Navigation
1. Using the menu buttons
When power on, press “MENU” on the device. The menu will display on the screen.
Press ▲ / ▼ button to choose menu item
Then press “MENU” button to conrm
ITEMS OPTIONS
Exit
Video Conguration Brightness, Contrast, Saturation, Sharpness, Color Temp, R Gain, G
Gain, B Gain, R O󰀨set, G O󰀨set, B O󰀨set
Marker Conguration Center Marker, Aspect Marker, Safety Marker, Marker Color, Marker
Mat, Thickness.
Function Conguration Scan, Aspect, Underscan, H/V Delay,
Check Field, Zoom, Freeze,3G Format, DSLR
Waveform Conguration Waveform, Waveform Trans, Peaking, Peaking Color, Peaking Level,
False Color, Exposure, Exposure Level, Histogram, Time Code
Audio Conguration Volume, Level Meter, Audio Ch
System Conguration Language, HDMI/SDI Convert, Color Bar, Menu Timer, Image Flip,
Back Light, Fan, Reset, Version

8Marshall Electronics
V-LCD70W-SH Operation Manual
ITEMS OPTIONS
Exit
Brightness 0~100
Contrast 0~100
Saturation 0~100
Sharpness 0~100
Color Temp
5500ºK / 6500ºK / 7500ºK / 9300ºK / User
R Gain 0-255
Note:
Only available under
“User” mode to meet
the color value you
need.
G Gain 0-255
B Gain 0-255
R O󰀨set 0-511
G O󰀨set 0-511
B O󰀨set 0-511
ITEMS OPTIONS
Exit
Center Marker On, O󰀨
Aspect Marker O󰀨, 3: 2, 4:3, 2.35:1, 1.85:1, 16:9
Safety Marker O󰀨, 80%, 85%, 88%, 90%, 93%, 95%
Marker Color Red, Green, Blue, White, Black
Marker Mat O󰀨, 1~7
Thickness 2, 4, 6
ITEMS OPTIONS
Exit
Scan Pix.To Pix. Zoom, Aspect,
Aspect 16:9, 1.85:1, 2.35:1, 4:3, 3:2, Full
Underscan On, O󰀨
H/V Delay O󰀨, H, V, H/V
Check Field O󰀨, Red, Green, Blue
Zoom ×2, ×3, ×4, ×5, ×6, ×7, ×8
Freeze ON, O󰀨
SDI INPUT
3G Format
Normal, GBRA444 10Bit, YCbCrA444 10Bit,
YCbCrA422 12Bit, GBR444 12Bit, YCbCr444
12Bit
HDMI INPUT
DSLR
5D3
5D2 DSLR MODE
OFF

9
www.LCDracks.com
Marshall Electronics
ITEMS OPTIONS
Exit
Waveform O󰀨, Multi, Y, YCbCr, RGB
Waveform Trans. O󰀨, 20%, 50%
Peaking On, O󰀨
Peaking Color Red, Green , Blue, White
Peaking Level 0~100
False Color On, O󰀨
Exposure On, O󰀨
Exposure Level 0~100
Histogram Y, RGB, Color
TimeCode (SDI Input Only) O󰀨, VITC, LTC
ITEMS OPTIONS
Exit
Language English, Chinese
HDMI/SDI Convert On, O󰀨
Color Bar On, O󰀨
Menu Timer 10s, 20s, 30s
Image Flip O󰀨, H, V, H/V
Back Light 0~100
Fan O󰀨, Low, High
Exposure Level On, O󰀨
Version V1.3
ITEMS OPTIONS
Exit
Volume 0~100
Level Meter On, O󰀨
Audio Ch Ch1&Ch2, Ch3&Ch4, Ch5&Ch6, Ch7&Ch8,
r

10 Marshall Electronics
V-LCD70W-SH Operation Manual
PANEL
Screen Size 7” Diagonal
Aspect Ratio 16:10
Resolution 1920 x 1200
Viewing Angle (h x v) 170° x 170° (H/V)
Brightness 450 cd/m2
Contrast Ratio 1000:1
VIDEO INPUT / OUTPUT* 3G-HD-SDI Input / Output 2 x BNC Female (75 Ω)
HDMI Input / Output 2 x HDMI Female
CONNECTORS
HDMI Video Input
HDMI Video Output
3G-HD-SDI Video Input
3G-HD-SDI Video Output
Tally Hardware Interface HD-15 Female
Stereo Headphone Jack 1/8” (3.5mm) Female Jack
Power Input DC Connector
ELECTRICAL Power Consumption 1.1A @ 12VDC (13 W)
Voltage Requirement 12 VDC (7 – 15VDC)
MECHANICAL
Weight 1.20 lbs
Operating Temperature -4°F ~ 140°F (-20°C ~ 60°C)
Storage Temperature -22°F ~ 158°F (-30°C ~ 70°C)
DIMENSIONS (H x W x D) 125mm x 196mm x 28.2mm / 4.9” x 7.7” x 1.11”
6. Specifications
TALLY HARDWARE INTERFACE (HD-15)
Activation requires contact closure of pin to ground on the HD-15 connector:
Pin No. Signal
1Green
2Red
3Yellow
4Ground
5NC
6N/C
7 N/C
8 N/C
9N/C
10 N/C
11 N/C
12 N/C
13 N/C
14 N/C
15 N/C
* Maximum 1 loop out for the best result