Masport 215 Series User manual

548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
masport.com Part No: 546948.A.3
Barbecues
MASPORT 4/6 BURNER 215 SERIES
OWNER’S MANUAL
Please read these instructions carefully before assembly, to
reduce risk of re, burn hazard or other injury.
Keep these instructions in a safe place for future use.
This BBQ is for Outdoor Use Only.
This manual covers a range of barbecues which include: Origin, Origin
Plus, Origin Deluxe, Elite, Equip 6 and Supreme.

2
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
CONTENTS
INTRODUCTION 3
SAFETY INFORMATION 3
SYMBOLS IN THIS OWNER’S MANUAL 3
IMPORTANT SAFETY INFORAMTION 3
WARRANTY INFORMATION 4
DISPOSAL OF PACKAGING 5
IMAGES 5
ASSEMBLY INSTRUCTIONS FOR BBQ WITHOUT CONDIMENT DRAWER 6
ASSEMBLY INSTRUCTIONS FOR BBQ WITH
CONDIMENTS DRAWER & OTHER FEATURES 13
INSERTING/CHANGING THE BATTERY 22
FAT AWAY DISCHARGE FUNCTION - GRILL AND PLATE ORIENTATION 23
FOR MODELS WITH ROTISSERIE - ASSEMBLY INSTRUCTIONS 24
NATURAL GAS CONVERSION 25
LEAK TESTING 25
INSTALLATION 25
OPERATION 26
TROUBLESHOOTING 30
PARTS LIST 31
FASTENER KITS 34
OPTIONAL EXTRAS 35
CARE AND MAINTENANCE 36
TECHNICAL DATA 39

3
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
INTRODUCTION
This product has many features for making its use more pleasant and
enjoyable. Safety, performance, and dependability have been given
top priority in the design of this product making it easy to maintain and
operate.
This BBQ is for Outdoor use only. Do not install in, or connect to the
consumer piping or gas supply system of a boat or caravan.
SAFETY INFORMATION
Keep the instructions in a safe place for
future use.
WARNING!
DO NOT OPERATE THIS BBQ BEFORE IT HAS BEEN
ASSEMBLED CORRECTLY AND YOU HAVE READ AND
UNDERSTOOD THESE INSTRUCTIONS.
READ
These instructions are intended as a general guide and
do not supersede national or local codes in any way.
Contact local authorities for clarity of laws relating to
the operation of this appliance.
SYMBOLS IN THIS OWNER’S
MANUAL
Possible hazard or hazardous situation.
Not observing this instruction can lead to injuries or
cause damage to property.
Important information on proper handling.
Not observing this instruction can lead to faults in
the BBQ.
User information. This information helps you to use all
the functions correctly.
Failure to follow these instructions could result in re or explosion
which could cause property damage, personal injury or death.
Accessible parts may be very hot. Keep young children away from
the hot appliance at all times (even while cooling down).
Some parts of this grill may have sharp edges especially as
mentioned in this manual! Wear suitable protective gloves if
necessary.
Assembled parts sealed by the manufacturer must not be altered
by the user. Any modication of the appliance by unauthorised
persons may be dangerous.
WARNING!
FOR OUTDOOR USE ONLY
WARNING!
To reduce the risk of re, burn hazard or other injury, read the
instructions carefully and be sure your appliance is properly
installed and assembled.
DANGER!
If you smell gas:
1. Shut o gas to the appliance;
2. Extinguish any open ame:
3. Open lid;
4. If odor continues, keep away from the appliance
and immediately call your gas supplier or your re
department.
WARNING!
TO INSTALLER:
Test operation of the appliance and instruct the user before
leaving. Ensure the appliance is commissioned correctly
before handing over to the user.
WARNING!
The grill head is heavy and will require two or more people to
lift and position onto the grill cart when assembly.
WARNING!
Do not try lighting this appliance without rst reading the
“LIGHTING INSTRUCTION” section of this manual.
WARNING!
Conversion to natural gas only done by authorized persons.
WARNING!
Always keep the electrical components in dry situation.
IMPORTANT SAFETY INFORAMTION
Please read and understand this manual fully before assembly and use.
• The Manufacturer’s Warranty may be voided by the incorrect use
of this product.
• The Manufacturer or their Agents can accept no liability for the
unsuitability of, or any damage to, food that is cooked on this
appliance.
• Use the correctly specied fuel with this barbecue. Check with
your dealer for the specic fuel for which this barbecue has been
designed.
OWNER’S MANUAL
• The operator must understand all the safety requirements
detailed in this manual before using the barbecue.
• If you have any queries regarding these instructions, contact
your local dealer for clarication before you use your barbecue.
• The unit must be correctly assembled before use. Failure to
follow the manual’s instructions could result in serious damage
or injury.
PERSONAL SAFETY
• The use of alcohol, prescription or non-prescription drugs may
impair the consumer’s ability to properly assemble or safely
operate this barbecue.
• The barbecue should be carefully checked for operational use
every time before use.

4
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
• Never try to move the barbecue when it is on, or before it has
had time to cool down.
• The person operating this barbecue should pay constant
attention to the food being cooked.
• Do not leave the barbecue unattended when it is alight. The
person should remain at the barbecue at all times when it is
alight/cooking.
THIRD PARTY SAFETY
• The operator is responsible for the safety of all third parties while
the barbecue is in use.
• Onlookers should be kept a safe distance away from the
barbecue when it is in use.
• Keep children and animals well away while the barbecue is in
use and while it is cooling down.
LOCATION
• Do not use indoors. Barbecue units are designed for OUTDOOR
USE ONLY.
• Use in a weather-protected area, preferably under shelter.
• Ensure that the barbecue is on an even and secure surface
before operating. Use the castor locks if tted to lock the wheels
in place.
• Do not use within one metre of any ammable surface of
structure.
BURN AWARENESS
• Parts of the barbecue do get extremely hot and could cause
serious burns – touch test the surface before applying a rm
grip.
• The hood handle can become hot! Always wear cooking gloves
and long sleeves when handling hot components.
• If cooking with the hood closed, be very careful opening the
hood, a sudden rush of hot air could burn an unprotected arm.
GAS AWARENESS
• Ensure all gas couplings and hoses are in good condition and
have been correctly tted.
• Leak test all gas lines and connections before use.
• Do not store ammable materials near this barbecue.
• Do not store spare LPG cylinders under or near this barbecue.
• Do not place or use aerosols near this barbecue.
• Do not store or use gasoline or other ammable vapours or
liquids in the vicinity of this barbecue.
• Ensure that the gas is turned OFF at the cylinder after use and
while the barbecue is unattended.
• When turning o the barbecue, shut o the gas at the supply
source before turning o all the burner controls.
• Do not lean over appliance when lighting.
• Do not use appliance with any cover on.
• Do not use plastic or glass utensils on the appliance.
• Do not dismantle control valves.
• Do not test for gas leaks with a naked ame.
• Do not modify the constructions of the appliance or the size of
any burner, injector orice or any other components
• Do not obstruct any ventilation of the appliance.
• Do not allow the exible gas supply hose or any electrical cord to
come in contact with any heated surface of the appliance.
• Do not use charcoal or any other solid fuel in this appliance.
• Do not disconnect any gas ttings while the appliance is in use.
• Do not use a rusty or dented gas cylinder with a damaged gas
valve.
• Do not ll the gas cylinder beyond 80% capacity.
• Do not store gas cylinders below ground level. ULPG is heavier
than air. Should a leak occur, the gas will collect and could ignite
due to presence of a ame or electric spark.
• Do not place articles on or against this appliance.
ELECTRICAL AWARENESS
• Symbol IEC 60417 - 5172 (2003-2) Class II equipment.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure they do not play with
the appliance.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarily qualied persons in
order to avoid a hazard.
• BBQs with Grill Lights & USB parts run on AC power. It is
IMPORTANT to ensure the care is taken to the location of the
BBQ. See section in this manual which refers to “Location”.
• Turn power OFF when not in use.
• Avoid using in wet conditions.
• If an external lead is being used, ensure that it is corectly rated
and meets current safety certication requirements.
• Ensure the power is turned OFF before connecting and
disconnecting any components on the BBQ.
• Ensure power leads are kept away from any hot parts of the
BBQ.
• Do not place the power lead where hot oil or fat can drip onto
the lead.
FOR YOUR SAFETY AND OTHERS
If you smell gas:
• Shut o the gas supply to the barbecue.
• Extinguish any open ame (candles, cigarettes, etc.)
• Clear the area to allow the unburned gas to dissipate.
• Be aware of the reason for the gas smell, address this before
continuing. Should the gas odour come from the LPG cylinder,
immediately contact the re department from an elevated safe
distance.
• Connecting the gas cylinder to the barbecue, refer to that
section in the manual.
• Leak testing, refer to that section in the manual.
SAFETY EQUIPMENT
• When cooking with oil/grease, re extinguishing materials should
be readily accessible.
• In the event of an oil/grease re do not attempt to extinguish with
water or alcohol. Use type BC dry chemical re extinguisher or
smother the re with dirt, sand or baking soda.
RAIN HAZARD
In the event of rain while cooking with oil/grease, turn o the gas supply
and all burners, cover the barbecue as soon as possible. Move people/
animals away from around the barbecue. Do not attempt to move the
barbecue until it has cooled and can safely be moved.
WARRANTY INFORMATION
WARRANTY
Refer to the warranty supplied with this BBQ. Should any part fail due to
defective workmanship or faulty materials within the specied period from
the date of purchase, Masport will replace or repair the defective part
free of charge. Refer to the warranty for details. Do not use a BBQ that is
unsafe.
LPG CYLINDER
The cylinder manufacturer/distributor is responsible for the safety and
performance of the LPG cylinder. This is not included in the Masport BBQ
warranty. Do not use a cylinder that is unsafe. Do not use an adaptor at
the cylinder connection.

5
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
DISPOSAL OF PACKAGING
Remove all protective packaging including any protective lm from stainless steel surfaces.
Make sure you properly dispose of, or recycle the packaging material where possible to comply with applicable waste disposal laws in your area.
IMAGES
NOTE:
The following pages contain assembly instructions for various model options. Please ensure you identify your BBQ model so that the
correct instructions can be follwoed.
When assembling the cabinet, leave all of the screws loose until completey assembled, then tighten all screws.

6
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
ASSEMBLY INSTRUCTIONS FOR BBQ WITHOUT CONDIMENT DRAWER
Product Description
Carton Identication
Product Part Number
Open the carton by removing the
shipping straps then slitting along both
ends. Cut the tape only by a small
amount in the middle, nish by lifting
the carton aps with your hand.
Unpack the entire carton, this carton
will be used as a surface protector as
the cabinet is being built. Open the
carton as shown and place where the
BBQ will be assembled
NOTE:
Letters in the bracket after every screw, helps you identify the item number from the parts list on page 6, from the fastener kit.
Tools needed for assembly: Crosshead screwdriver, 10mm A/F Spanner
Open the fastener kit, place to one side, 4 pcs screw (SS) M6x12 (item b) & 4pcs bre washer (item c) for Hood Assembly.
Before commencing assembly, open the cartons and lay all of the components on the oor. Familarise them against the parts list on page 21, as some
of these instructions refer to this parts list.
NOTE:
When assembling the barbecue, ensure it is sitting on a at surface.
5. Assemble 1pc Front skirt (item 2) to the Base tray (item 1) using 2pcs Screw M6×12 (item a) from the fastener kit.
2
Screw M6*12
6. Assemble 1pc Left skirt (item 3) to the Base tray using 3pcs Screw M6×12 (item a) and 1pc Screw M5*10 (item d) from the fastener kit.
3
Screw M6*12 Screw M5*10

7
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
7. Assemble 1pc Right skirt (item 4) to the Base tray using 3pcs Screw M6×12 (item a) and 1pc Screw M5*10 (item d) from the
fastener kit.
Screw M5*10 4
Screw M6*12
Rear of the
barbecue
8. Assemble 4pcs Castors (item 5) to the Base tray using 16pcs Screw M6×12 (item a) from the fastener kit.
NOTE:
Assemble the casters and lock the rear castors before assembling the cabinet
Screw M6*12
5
Lock this castor
Lock this
castor
Front of the
barbecue
M6*12
Spring Washer
Washer
Locking the rear castors will steady the base. Position the base with the locks facing outwards.
NOTE:
Here on going forward keep the screws loose until the cabinet structure is complete. This will greatly assist with positioning
the panels. Tighten all screws when cabinet is assembled.
9. Assemble the Left panel (item 6) and Right panel (item 7) to the Base tray using 4pcs Screw M6×12 (item a) from the fastener kit.
M6*12
7
6
Screw M6*12

8
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
10. Assemble the Back panel (item 8) using 5pcs Screw M6×12 (item a) from the fastener kit.
M6*12 8
Screw M6*12
Front of the barbecue
NOTE:
Assemble the side panels before assembling the top panel on the cabinet then assemble this sub-assembly on the
barbecue
Step 1. Assemble the side panels (item 37) to the top cabinet panel (item 36) using 3 xM6 x12 screws (item a)
each side.
Side
Panels
Top Cabinet
Panel
Top Cabinet Panel Side Panel
Step 2. Step 2 – Assemble this panel sub assembly to the rear panel of the cabinet using 3 xM6 x12 screws (item
a).

9
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
Step 3. Insert the top front panel with the side panel extension inside the panel as shown to provide the strength.
Step 4. Assemble the door panel to the side panels of the cabinet using 2 xM6 x12 (item a) screws each side.
Keep the screws loose.
Door Panel
Side Panel
Cabinent
Step 5. Assemble the door panel and the top cabinet panel using 4 xM6 x12 screws (item a). Keep the screws
loose.
Step 6. Once all the parts mentioned above are assembled tighten all the screws.

10
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
9. Assemble Left door (item 10) and Right door (item 11) using 4pcs Screw M6×12 (item a), 4 Handle brackets (item 12) and 2
Handles (item 13), then assemble the door assemblies as the picture.
Note!
Once the cabinet has been fully assembled, and
the doors open and close correctly with even
clearances top and bottom, and side to side, the
screws can now be fully tightened.
Note!
To keep screw slot against screwdriver pass
screw through ribbon of plastic, hold both
together, assemble screw to handle, remove
plastic, and re-use for other three screws.
M6*12
Screw M6*12
11
13
12
10
PREPARING THE HOOD / GRILL ASSEMBLY
Open the hood carton and remove the warming rack (item 23)
Lift up and out the polystyrene corner packing.
Remove the protective layer from the hood.
Cut open all sides with a knife taking care not to damage the hood or grill in the process.
• Open the carton walls outwards and atten. Remove the polystyrene packing from beneath the grill.
Open the hood and remove in order:
• Packed cartons (some are empty and used as a gap ller) and any polystyrene packaging
• Grill rst, then hotplate
• Remove the layer of cardboard
• Remove extra feature options if any. Some specic barbecue models include some extra feature items.
• At the rear you will locate the drip tray (item 18) remove this, (it is packed in the reverse). This may require the removal of the 2x step Screws
(item e)
• The Hood / Grill is now ready to be lifted onto the cabinet. This is a large and heavy assembly which requires two persons to lift it safely into
position.
10. 1) Assemble the hood and grill assembly (item 14) to the cabinet trolley with 4pcs Screw (SS) M6*12 (item b) and 4pcs bre washer (item c) from
the fastener kit.
2) In some barbecue models the knobs are not tted to the grill then assemble 6 pcs knob (item 15) to the valve shaft on the body
assembly, as per the illusration below.
3) If the rear burner knob is not tted to the grill assemble 1 x knob - Rear burner (item 34) to the Rear burner valve shaft.
When the Timer is OFF the flat on the
shaft faces the Bottom / 6 o’clock
position and the Flat on the knob
insert should match this position.
When the Timer is OFF the rounded shaft contour faces the
Top/ 12 o’clock position and the flat spring metal insert grips
the round face of the shaft of valve.

11
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
Screw SS M6*12
Big bre washer
14
Screw SS M6*12
Big bre washer
14
15
11. Loosen the 3 Screws (item b), remove the 4th & 5th screws, then assemble the heat shield (item 33) and left hand side shelf (item 16) to the
appliance with 5pcs Screw (SS) M6*12 (item b). Level the top of the table and secure.
If the timer knob is not tted then, t one knob (item 15) on the shaft of the timer on the side table. Refer to the timer section for correct operating
procedure.
12. Loosen fully but do not remove 4 screws (item b) as shown. Remove two screws 5 & 6, lower the side table over the screw heads. Fasten the four
screws to secure the side table. Ret screws 5 & 6, screw 6 secures the facia which may require frontal pressure to align this hole. Level the top of
the table and secure.
15
Screw SS M6*12 (b)
16 (b)
13. 1) Remove all packaging from the side burner prior to tting the Right Hand (side Burner) table to the BBQ. Prepare the BBQ prior
to tting the side table, refer to previous instructions. Then assemble the Side burner assembly (item 17) as described in step 13. If the
knob (item 15) has not been tted then assemble the knob (item 15) to the valve shaft on side burner assembly (item 17), and make sure the
red point on the knob is on the upper direction.
2) Connect the side burner hose to the main manifold, and tighten carefully.
Screw SS M6*12
Big Fibre Washer
16 (b)
33
Screw SS M6*12 (b)
15

12
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
Note!
Before operating this appliance for the rst
time LEAK TEST ALL JOINTS.
14. Put the Drip tray (item 18), Grease cup (item 19) into the grill body and 2pcs Step screw (item e) - (the step screws will be on the
assembly already) to the rear of the grill body to secure the drip tray.
NOTE:
Some barbecue models require the stepped screws (item e) are removed to insert the drip tray. Once the tray is positioned
correctly, ret step screw (item e).
18
19
Step screw (e)

13
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
ASSEMBLY INSTRUCTIONS FOR BBQ WITH
CONDIMENTS DRAWER & OTHER FEATURES
Product Description
Carton Identication
Product Part Number
Open the carton by removing the
shipping straps then slitting along both
ends. Cut the tape only by a small
amount in the middle, nish by lifting the
carton aps with your hand.
Unpack the entire carton, this carton will
be used as a surface protector as the
cabinet is being built. Open the carton
as shown and place where the BBQ will
be assembled
NOTE:
Letters in the bracket after every screw, helps you identify the item number from the parts list on page 6, from the fastener kit.
Tools needed for assembly: Crosshead screwdriver, 10mm A/F Spanner
Open the fastener kit, place to one side, 4 pcs screw (SS) M6x12 (item b) & 4pcs bre washer (item c) for Hood Assembly.
Before commencing assembly, open the cartons and lay all of the components on the oor. Familarise them against the parts list on page 21, as some
of these instructions refer to this parts list.
NOTE:
When assembling the barbecue, ensure it is sitting on a at surface.
1. Assemble 1pc Front skirt (item 2) to the Base tray (item 1) using 2pcs Screw M6×12 (item a) from the fastener kit.
2
Screw M6*12
2. Assemble 1pc Left skirt (item 3) to the Base tray using 3pcs Screw M6×12 (item a) and 1pc Screw M5*10 (item d) from the fastener kit.
3
Screw M6*12 Screw M5*10

14
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
3. Assemble 1pc Right skirt (item 4) to the Base tray using 3pcs Screw M6×12 (item a) and 1pc Screw M5*10 (item d) from the fastener kit.
Screw M5*10 4
Screw M6*12
Rear of the
barbecue
4. Assemble 4pcs Castors (item 5) to the Base tray using 16pcs Screw M6×12 (item a) from the fastener kit.
NOTE:
Assemble the casters and lock the rear castors before assembling the cabinet
Screw M6*12
5
Lock this castor
Lock this
castor
Front of the
barbecue
M6*12
Spring Washer
Washer
Locking the rear castors will steady the base. Position the base with the locks facing outwards.
NOTE:
Here on going forward keep the screws loose until the cabinet structure is complete. This will greatly assist with positioning the panels.
Tighten all screws when cabinet is assembled.
5. Assemble the Left panel (item 6) and Right panel (item 7) to the Base tray using 4pcs Screw M6×12 (item a) from the fastener kit.
M6*12
7
6
Screw M6*12

15
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
6. Assemble the Back panel (item 8) using 5pcs Screw M6 x 12 (item a) from the fastener kit.
7. Assemble the side panels before assembling the top panel on the cabinet then assemble this sub-assembly on the barbecue.
Screw M6x12
36
8. Assemble the side panels before assembling the top panel on the cabinet then assemble this sub-assembly on the barbecue.
Screw M6x12
(countersunk head screw)
42
42

16
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
9. Assemble Left door (item 10) and Right door (item 11) using 4pcs Screw M6x12 (item a), 4 Handle brackets (item 12) and 2 Handles (item 13). then
assembl;e the door assemblies as pictured.
Screw
M6x12
12
10
11
13
NOTE:
To keep screw slot against screwdriver pass
screw through ribbon of plastic, hold both
together, assemble screw to handle, remove
plastic and re-use for the other three screws.
NOTE:
Once the cabinet has been fully assembled,
and the doors open and close correctly
with even clearances (top and bottom and
side-to-side), the screws can now be fully
tightened.
10. Assemble Left door (item 10) and Right door (item 11) using 4pcs Screw M6x12 (item a), 4 Handle brackets (item 12) and 2 Handles (item 13). then
assembl;e the door assemblies as pictured.
Screw M4x12
a
a-1
a-2
a-3
REPARING THE HOOD / GRILL ASSEMBLY
- Open the hood carton and remove the warming rack (item 23)
- Lift up and out the polystyrene corner packing.
- Remove the protective layer from the hood.
- Cut open all sides with a knife taking care not to damage the hood or grill in the process.
- Open the carton walls outwards and atten. Remove the polystyrene packing from beneath the grill.
Open the hood and remove in order:
• Packed cartons (some are empty and used as a gap ller) and any polystyrene packaging
• Grill rst, then hotplate
• Remove the layer of cardboard
• Remove extra feature options if any. Some specic barbecue models include some extra feature items.
• At the rear you will locate the drip tray (item 18) remove this, (it is packed in the reverse). This may require the removal of the 2x step Screws
(item e)
• The Hood / Grill is now ready to be lifted onto the cabinet. This is a large and heavy assembly which requires two persons to lift it safely into
position.
11. 1) In some barbecue models the knobs are not tted to the grill then assemble 6 pcs knob (item 15) to the valve shaft on the body assembly, as

17
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
per the illusration below.
2) If the rear burner knob is not tted to the grill assemble 1 x knob - Rear burner (item 34) to the Rear burner valve shaft.
When the Timer is OFF the flat on the
shaft faces the Bottom / 6 o’clock
position and the Flat on the knob
insert should match this position.
When the Timer is OFF the rounded shaft contour faces the
Top/ 12 o’clock position and the flat spring metal insert grips
the round face of the shaft of valve.
12. Assemble the grill body onto the trolley by using 4pcs Screw M4x12, and then assemble the bottle opener on the left side panel by using 2pcs
M4x12.
13. Loosen the 3 Screws (item b), remove the 4th & 5th screws, then assemble the heat shield (item 33) and left hand side shelf (item 16) to the

18
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
appliance with 5pcs Screw (SS) M6*12 (item b). Level the top of the table and secure.
If the timer knob is not tted then, t one knob (item 15) on the shaft of the timer on the side table. Refer to the timer section for correct operating
procedure.
Screw SS M6*12
Big bre washer
14
Screw SS M6*12
Big bre washer
14
15
14. 1) Remove all packaging from the side burner prior to tting the Right Hand (side Burner) table to the BBQ. Prepare the BBQ prior
to tting the side table, refer to previous instructions. Then assemble the Side burner assembly (item 17) as described in step
13. If the knob (item 15) has not been tted then assemble the knob (item 15) to the valve shaft on side burner assembly (item
17), and make sure the red point on the knob is on the upper direction.
2) Connect the side burner hose to the main manifold, and tighten carefully.
NOTE!
Before operating this appliance for the rst time
LEAK TEST ALL JOINTS.
Screw SS M6*12
Big Fibre Washer

19
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
15. Put the Drip tray (item 18), Grease cup (item 19) into the grill body and 2pcs Step screw (item e) - (the step screws will be on the
assembly already) to the rear of the grill body to secure the drip tray.
NOTE:
Some barbecue models require the stepped screws (item e) are removed to insert the drip tray. Once the tray is positioned
correctly, ret step screw (item e).
16. Insert the wiring plug of transformer into the bottom of the transformer connector. And then fasten the nut by turning clockwise. The lead from the
Transformer to the lights is to be routed on the outside of the BBQ Cabinet. It is designed to be just long enough in length to do this (will be too
short if routed on the inside of the Cabinet).
17. Insert the wiring plug of USB into the USB port (if included in your model of BBQ).
18. Connecting the ignition wire/ wires to the electronic module

20
548948.A.3 - Masport 4/6 Burner 215 Series June 2021 PANTONE 648C
NOTE:
1. The rear burner valves operate with the electronic ignition.
2. All the side burner valves operate with the integrated ignition.
Check the diagram of module to determine the BBQ ignition type
3. If the module has only one pin i.e. connecting single wire then Rear burner operates with electronic ignition
4. If the module has multiple pins for connecting the wires then Rear burner and Main burners operate with electronic
ignition.
Single Pin Electronic
module
4 Pin Electronic module 6 Pin Electronic module 7 Pin Electronic module
Ignition module attached on
the Right side Table
Follow the diagram to connect the wires between the electronic module and the electrode.
Connect the lead wire with the electronic ignition as shown below. Make sure that the wire is clipped tight.
SINGLE PIN ELECTRONIC MODULE:
Connect the lead wire with
the electronic ignition, no
sequence is required,
Connect the lead wire with
the electronic ignition, no
sequence is required,
4 / 6 / 7 Pin Electronic Module: