Matchmaster 34MM-HDS2 User manual
AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ PAGE | 1 OF 2
34MM-HDS2
INSTRUCTION MANUAL
STATEMENT
FEATURES
PANEL DESCRIPTION
DIP SWITCH OPERATION
SAFETY PRECAUTION
AFTER-SALES SERVICE
PACKING LIST
PRODUCT INTRODUCTION
Thanks for purchasing this product, please read this user
manual carefully before using this product. The functions
described in this version are updated till July, 2019. In the
constant effort to improve our product, we reserve the right
to make functions or parameters changes without notice or
obligation.
We provide limited warranty for the product
within three years.
• 1x HDMI 2.0 1x2 Splitter
• 4x Plastic Cushions
• 1x Power Adapter (5V DC 1A)
• 1x User Manual
Note: Please contact your distributor immediately if any damage or defect in
the components is found.
• Do not dismantle the housing or modify the module to
avoid electrical shock or burn.
• Using supplies not meeting the products’ specications
may cause damage, deterioration or malfunction.
• Do not expose the unit to rain, moisture or install this
product near water.
• Install the device in a place with ne ventilation.
• Do not twist or pull by force ends of the optical cable.
It can cause malfunction.
• Do not use liquid or aerosol cleaners to clean this unit.
• Always unplug the power to the device before cleaning.
• Unplug the power when not used for a long period of time.
• Refer all servicing to qualied service personnel.
Thanks for choosing the HDMI 2.0 1x2 Splitter, which can
distribute one HDMI input to two outputs. The splitter
supports HDMI video resolution up to 4K@60Hz 4:4:4,
1080p 3D, and multichannel audio formats. Besides passing
EDID information from the display, there are multiple built-in
EDID settings can be selected by the 4-pin DIP switch on
the front panel. Moreover, the splitter supports convenient
rmware upgrade through Micro-USB port.
• Supports HDMI 2.0 and the video resolution up to
4K@60Hz 4:4:4.
• HDMI input supports HDCP 2.3 and the outputs support
HDCP Active or HDCP Passive mode.
• Supports video resolution down-scaling, the 4K input
can be automatically degraded to 1080p output for
compatibility with 1080p display.
• 18Gbps high bandwidth.
• Advanced EDID management: multiple built-in EDID
settings can be selected.
• Built-in equalizer for signal enhancement to avoid signal
attenuation in transmission.
• Supports CEC pass-through.
• Provides LEDs to indicate the current operating status.
• Firmware upgrade by Micro-USB port.
Front Panel
EDID Management
Rear Panel
1 2 3 4 5
1. POWER LED: The LED illuminates red when
2. power is applied.
3. INPUT LED: The LED illuminates blue when
4. there is HDMI input.
5. OUTPUT LEDs: The LED illuminates blue when there is
HDMI output on the corresponding channel.
6. EDID: 4-pin DIP switch for EDID setting and HDCP mode
selection. Please refer to the EDID Management for
more details.
7. FW: Micro-USB port for rmware upgrade.
1. INPUT: Type-A female HDMI input port to connect
a HDMI source.
2. OUTPUTS: Two type-A female HDMI output ports
to connect HDMI displays.
3. DC 5V: DC barrel port to connect an AC power adapter.
1 2 3
IN OUT 1 OUT 2 DC 5V
The Extended Display Identication Data (EDID) is used
by the source device to match its video resolution with the
connected display. By default, the source device obtains
its EDID from the rst connected display. Meanwhile, since
the displays with different capabilities are connected to the
splitter, the DIP switch on the front panel can be used to
set the EDID to a xed value to ensure the compatibility in
video resolution.The switch represents “0” when in the lower
(OFF) position, and it represents “1” while putting the switch
in the upper (ON) position.
PAGE 2 OF 2 | AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ
Switch 1~3 are used for EDID setting. The DIP
switch status and its corresponding setting
are shown at the back of the product.
Put the switch 4 on the “ON” position to select HDCP Active
mode, or on the “OFF” position for HDCP Passive mode.
The product supports video resolution down-scaling, the 4K
input can be automatically degraded to 1080p output for
compatibility with 1080p display, shown in the below chart.
1 2 3 4
EDID Setting
1080p DTS/Dolby
4K/30Hz LPCM
4K/60Hz LPCM
4K/60Hz DTS/Dolby
Default
1 2 3 4
ON
OFF
1
0ON
OFF
ON
OFF
123
Priority OUT 1 > 2
ON
OFF
123
Priority OUT 2 > 1
ON
OFF
123
ON
OFF
123
1080p LPCM
ON
OFF
1 2 3
ON
OFF
1 2 3
ON
OFF
1 2 3
ON
OFF
1 2 3
4K/30Hz DTS/Dolby
Switch Status Video Resolution Audio Format
000 Obtains EDID from the rst detected
display starting at HDMI output 1>2.
001 Obtains EDID from the rst detected
display starting at HDMI output 2>1.
010 1080p LPCM
011 1080p DTS/Dolby
100 3840x2160@30Hz HDR LPCM
101 3840x2160@30Hz HDR DTS/Dolby
110 3840x2160@30Hz HDR LPCM
111 3840x2160@30Hz HDR DTS/Dolby
HDCP Mode
Switch Status Mode HDCP
OFF (0) Passive (Default) Automatically follows
the display’s HDCP
version
ON (1) Active Automatically
removes the HDCP
content of HDMI
output for broader
video solution.
VIDEO RESOLUTION DOWN-SCALING
FIRMWARE UPGRADE
SYSTEM CONNECTION
TECHNICAL SPECIFICATION
Input Output
# Resolution Refresh Color
Space
Downscale 1080p Specs
1 3840x2160 60 4:4:4 Yes 1080p@60Hz
4:4:4
2 3840x2160 30 4:4:4 Yes 1080p@30Hz
4:4:4
3 3840x2160 24 4:4:4 Yes 1080p@24Hz
4:4:4
4 3840x2160 60 4:2:0 Yes 1080p@60Hz
4:4:4
5 3840x2160 30 4:2:0 Yes 1080p@30Hz
4:4:4
6 3840x2160 24 4:2:0 Yes 1080p@24Hz
4:4:4
7 3840x2160 60 4:2:2 No N/A
8 3840x2160 30 4:2:2 No N/A
9 3840x2160 24 4:2:2 No N/A
Please follow the below steps to upgrade rmware by the
Micro-USB port:
1. Connect the splitter to the PC with USB cable.
2. Power on the splitter, and then the PC will automatically
detect a U-disk named of “BOOTDISK”.
3. Double-click to open the U-disk, a le named of
“READY.TXT” will be showed.
4. Copy the latest upgrade le (.bin) to the “BOOTDISK”
U-disk directly.
5. If the lename “READY.TXT” automatically turns
to “SUCCESS.TXT”, the rmware was upgraded
successfully. If the rmware upgrade failed, please check
the le (.bin) and then follow the above procedure to
operate again.
6. Remove the USB cable after rmware upgrade.
Video Input
Input (1) HDMI
Input Connector (1) Type-A female HDMI
HDMI Input Resolution Up to 4Kx2K@60Hz 4:4:4
8bit
HDMI Standard 2.0
HDCP Version 2 .3, 1.4 compliant
CEC Supported
Video Output
Output (2) HDMI
Output Connector (2) Type-A female HDMI
HDMI Output Resolution Up to 4Kx2K@60Hz 4:4:4
8bit
HDMI Standard 2.0
HDCP Version 2.3, 1.4 compliant
CEC Supported
Control
Control Part (1) EDID 4-pin DIP switch,
(1) Micro-USB port
General
Bandwidth 18Gbps
HDMI 2.0 Cable Length 4K@60Hz 4:4:4 ≤5m,
4K@60Hz 4:2:0 ≤15m,
1080p ≤20m
Operation Temperature -10°c ~ +55°c
Storage Temperature -25°c ~ +70°c
Relative Humility 10%-90%
Power Supply Input:100V~240V AC; Out-
put: 5V DC 1A
Power Consumption 1.5W (Max)
Dimension (WxHxD) 96.0 x 17.6 x 70.4mm
Net Weight 185g
Note: Please adopt high-qualied HDMI cable fully compliant with HDMI 2.0
for reliable transmission and connection.
The following diagram illustrates the typical
input and output connection of the splitter: 4K/60 Display
Down Scaling
4K@60 4:4:4 HDR
4K/60 Blu-ray
1080p Display
Other Matchmaster Accessories manuals
