Matsushima MSC-01 User manual

－0－
TMSC-001E
Rev2:Dec.19,2017
INSTRUCTION MANUAL
FOR
Matsushima signal Conditioner
TYPE
MSC-01
1-8-18 Norimatsu-Higashi,Yahatanishi-ku,Kitakyushu 807-0837 Japan
Phone No.(8193)691-3731 Fax No.(8193)691-3735
http://www.matsushima-m-tech.com
E-mail [e-mail]
※The operator should read this Instruction Manual carefully and
handle the device correctly.

－1－
Table of Contents
Page
Table of Contents ・・・・・・・・・・・・・・・・・・・・・・ 1
SafetyPrecautions ・・・・・・・・・・・・・・・・・・・・・・ 2
１. Overview ・・・・・・・・・・・・・・・・・・・・・・・・・ 3
２. Specifications ・・・・・・・・・・・・・・・・・・・・・・・・
3
３. External Dimensions ・・・・・・・・・・・・・・・・・・・・・ 4
４. Names of Parts ・・・・・・・・・・・・・・・・・・・・・・・・ 4
５. Installation Method ・・・・・・・・・・・・・・・・・・・・・・
5
5- 1. Installation Method ・・・・・・・・・・・・・・・・・・・・ 5
5- 2. Remove Method ・・・・・・・・・・・・・・・・・・・・・・ 5
６. Connection Method ・・・・・・・・・・・・・・・・・・・・・・
5
6- 1. Terminal Layout ・・・・・・・・・・・・・・・・・ 5
6- 2. Connection Terminal ・・・・・・・・・・・・・・・・・・・ 6
6- 3. Operation of Contacts and LED Operations ・・・・・・・・・・ 6
6- 4. BlockDiagram ・・・・・・・・・・・・・・・・・・・・・・・ 7
７. Start-up ・・・・・・・・・・・・・・・・・・・・・・・・・・
8
7- 1. Warming-up Operation and Start-up Flow ・・・・・・・・・・・ 8
7- 2. LCD Screen and Button Operations ・・・・・・・・・・・・・ 9
８. Settings and Functions ・・・・・・・・・・・・・・・・・・・・・ 10
8- 1. Display Unit Setting ・・・・・・・・・・・・・・・・・・・・ 11
8- 2. Decimal point position Setting ・・・・・・・・・・・・・・・・ 12
8- 3. Scaling Setting ・・・・・・・・・・・・・・・・・・・・・・ 13
8- 4. No.1 Limit Setting ・・・・・・・・・・・・・・・・・・・・・ 14
8- 5. No.2 Limit Setting ・・・・・・・・・・・・・・・・・・・・・ 15
8- 6. Sensor Failure Relay Setting ・・・・・・・・・・・・・・・・ 16
8- 7. Sensor Failure Mode Setting ・・・・・・・・・・・・・・・・ 17
8- 8. Damping Setting ・・・・・・・・・・・・・・・・・・・・・・ 18
8- 9. Failure Setup. In Setting ・・・・・・・・・・・・・・・・・・ 19
8-10. Analog Output Setting（Test） ・・・・・・・・・・・・・・・・ 20
8-11. No.1 Relay Output Setting（Test）・・・・・・・・・・・・・ 21
8-12. No.2 Relay Output Setting（Test）・・・・・・・・・・・・・ 22
8-13. Equipment Failure Output Setting（Test） ・・・・・・・・・・・ 23
8-14. Sensor Failure Relay Output Setting（Test）・・・・・・・・・ 24
8-15. Parameter Reset ・・・・・・・・・・・・・・・・・・・・・・ 25
8-16. Factory Reset ・・・・・・・・・・・・・・・・・・・・・・・ 26
8-17. Language Setting ・・・・・・・・・・・・・・・・・・・・・ 27
8-18. Device information ・・・・・・・・・・・・・・・・・・・・ 28
９. Standard Factory Settings ・・・・・・・・・・・・・・・・・・・
29
10. Troubleshooting ・・・・・・・・・・・・・・・・・・・・・・・・ 30

－2－
Safety Precautions
Besure tothoroughlyread theinstructionmanual beforeusing theproducts.
Keeptheinstructionmanualinasafe,convenientlocationforfuturereference.
Allor part ofthecontentsdescribedinthismanualmaybechangedwithout anynotice.
Due to our constant striving for further improvement of products, partsor products that differ from those described in
thismanualmaybesubstituted.
WARNING(FailuretoobservethisWARNINGmaycauseafatalorseriousinjury.)
Besuretoconfirmthatanyperipheralequipmentdoesnotmovebeforeinstallationwork.
Inaddition,observe safetyrequirementsforinstallation work wherehigh-placeworkisexpected.
Besuretoturnoffthepowersourcebeforewiring,mountingandtransportationwork.(Failuretoobservethis
WARNINGmay resultinanelectric shock/injury orequipment damageduetoshort-circuit.)
Carryoutwiringworkcorrectlywithreferencetoaproperdrawing.
Never disassemblethe equipment. (FailuretoobservethisWARNING mayresultinan electricshock.)
Donotopenthecoverunderanexplosiveenvironmentalconditionwhenpowerisentered. (Failuretoobservethis
WARNINGmay resultinaninjuryorequipment damage.)
Donotplaceorstoretheequipmentinanyhostileenvironmentalplacewhereitwillbesubjectedtodirect
sunlight,rain, water droplet, hazardousgas/water,etc..
CAUTION(FailuretoobservethisCAUTIONmaycauseamoderate injuryorequipmentdamage.)
Donot usetheequipment foranypurposeotherthantheoriginalpurposeofuse.
Besuretoconfirmthespecificationof equipment andusetheequipmentwithintherangeof specification.
(Mountingconditions suchastemperature,powersource,frequency,etc.)
Makesureacorrectwiringbeforeapplyingpowersource.
Donothaveashockorstrongimpacttotheequipment.
(FailuretoobservethisCAUTIONmayresultinequipmentdamage.)
Besure toconnectnecessaryterminals(grounding,etc.).
Removeallwiringtotheequipment beforedoingelectricalweldingworkneartheequipment.
Donotforcedlybendorpulltheleadwirealsodonot useunnecessarilylongwire.
Tightenthe cover,leadoutlet,etc. properlysothatdust,rainwater,etc.donotenterinsidetheequipment.
Donotusetheequipmentunderacorrosivecondition(NH3,SO2,CI2,etc.).
Besuretotighten thecablegrandsothatouterairdoes notenterinside theequipment.
Whenapplyingpiping connectionsuchasconduit, etc. insteadof cablegrand,applyputtyorequivalentsonthecable
entrysothatouterairdoesnotenterinsidetheequipment.
IMPORTANT(indicatesnotesorinformationtohelpcustomers.)
LimitationsofWarranty:
Warrantyperiodshallbeoneyearfromthedateof delivery(ex-factory).
Anydamageofanyotherproducts that haveoccurredforuseoftheequipmentisnotcoveredbythiswarranty.
Alsoanylossinducedbyfailureormalfunctionoftheequipmentisnotcoveredbythiswarranty.
Failureormalfunctioncausedbyfollowing arenotcoveredbythiswarranty:
a. ModificationorrepairbyapartyotherthanMATSUSHIMA’sauthorizedpersonnel,orreplacement of
parts notrecommendedby MATSUSHIMA.
b. Inadequatestorage,installation,use, inspectionormaintenancethatdoes notcomplywithspecifications.
c. Causeforanyperipheralequipmentordevice.
d. Accidentbeyond control andforcemajeure (fire, earthquake,flood, riots,etc.).
LackofinstructionstoMATSUSHIMAforinformationorsafetyrequirementsthatcanbepredictedonly
bycustomers’side.
Thiswarrantyconditionsdonotlimitcustomers’legal right.
Pricefortheequipment doesnotincludeanycharge forservicessuchas commissioning,supervising, etc..
!
!
!

－3－
１．Overview
MSC-01isusedincombinationwithonetwo-wiretransmitteror4-20mADCcurrentoutputdevice.
Thisproductoutputstheinstrumentationsignalandcontactsignalof4-20mADCor1-5VDCcorrespondingto
the input currentsignal.
２．Specification
1. Type MSC-01
2. Power 85～264VAC，47～63Hz
3. Powerconsumption Approx.3W
4.
Inputsignal (※1) 4～20mADC （inputloadresistance：250Ω）
Currentlimited：3～24mADC
5.
2-wire
Sensor
power
supply
Noload 24VDC （20～28VDC）
20mALoad 18VDCormore
Short-circuitprotection Max.30mADC （Shortcircuitduration ：unlimited）
6.
Output
signal
(Isolated)
Analogoutput
4～20mADC ×１ （Loadresistance：Max.500Ω）
1～5VDC ×１
Resolution ：1uA（0.25mV）
Relayoutput
4-SPDTRelayoutput
(Limit×2，Transducerfailure×1，Sensorfailure×1) (※2)
Contactcapacity ：250V5AAC／30V5ADC
Minimumhysteresisofsetting ：0.1%
7. Display LCD
LCD digitaldisplay
Displaysettingrange ：-99999～99999
Decimalpointsettingrange ：0to 3digits after thedecimalpoint
(00000. ～00.000)
Unit:Selection( ％，ton，ｍ，ｆｔ，Pa，kPa，MPa，bar，kgf/cm2
psi，mg/m3，µg/m3，m3/h，ft3/h，t/h，kg/h
lb/h，mL/s，℃，°F，mA，Blank 《Non-display》)
LED Power （Green）×1，Limit （Yellow）×2
Fault （Red）×1，Sensorfailure （Red）×1 (※2)
8. Installation Method DIN-Rail
9. ConnectionMethod M3-Screwterminal （Tighteningtorque：0.5N・m）
10. Material Case PPO(Norylresin)
Terminalscrew Steel＋Nicoat
11. Operatingtemperature －15°C ～＋55°C
12. Operatinghumidity 30～90 ％RH （Nocondensing）
13. Protection IP20
14. Mass Approx.300g
15. Insulationresistance Inputcircuit-Outputcircuit-Powercircuit：100MΩormore/500VDC
16. Withstandvoltage Inputcircuit–Outputcircuit–Powercircuit-Earth：1500VAC 1min.
17. Accessories Terminalpin for HARTcommunication×2
（※1）Totheconnectionterminal fortwo-wiresensoror current output device,connect either ofthesedevices.
（※2）Thesensorfailureisuseful whentheconnectionequipmentcanburnoutacurrentsignalincaseofabnormality.
Table1
．
Product

－4－
３．External Dimensions ( Schematic Diagram )
４．Names of Parts
(58)【2.2835】(106)【4.1732】
(89.8)【3.5354】
20
-
M3
terminal
screw
Fig.1
．
Productexternaldimension
s
Unit:mm 【Inch】
Power
LED
（
Green
）
HARTsensorconnectionterminal
Main
unit
Limit
LED
（
Yellow
）
Equipmenterror
LED
（
Red
）
Sensorerror
LED
（
Red
）
Operationbutton
LCD
displayscreen
Fixingscrewofterminal
(M3)
Slider
T
erminal
block
Fig.2
．
Name
sofparts
※Theterminalblockcanbeattached/detachedindependently.
Whenenergizingtheproduct,besuretoconfirm thattheterminal blockis attached.
DIN-Rail

－5－
５．Installation Method
※Inanenvironment withalotofdust,metalpowder,etc.,placetheproductinadust-proofcaseand
takeheat radiationmeasures.
※Avoidvibrationsandimpactsasmuchaspossible,sincetheymaycausefailures.
※Avoiduseinaplacewheretheambienttemperatureexceedstherangeof-15°Cto+55°C(13°Fto131°F),
wheretheambienthumidityexceedstherangeof30to90%RH,orwherecondensationoccurs,sinceit
affectsthelifetimeandoperation.
InstalltheproductontheDINrailwiththeslidersidefacingdown.
5-1.Installation Method
AsshowninFigure3,hangtheupperhookontherearsideontheDINrail,andthenpushthebottompartto
installtheproduct.
5-2.RemoveMethod
AsshowninFigure4,pushdownthesliderusingaminusscrew-driver,pulloutthebottompartfromthe
DINrail,andthenremovetheequipmentfromtheDINrail.
６．Connection Method
※Donot installwires(powersupplywires,inputsignalwires,andoutputsignalwires)closetonoise
sources(switches,relay driving wires,highfrequencylines,etc.).
※Donot bindwirestogetherwiththoseinwhichnoiseorsurgeismixed,norinstallthem intothesameconduit.
6-1.TerminalLayout
Hereistheterminalnumberlayout ofthe terminal block.
1 2 3 4 5 6 7 8 9 10
11 12 13
14 15 16 17 18
19 20
①
②
①
②
③
Fig.3．DIN rail installation Fig.4．DINrailremoval
Fig.5．Terminalnumberlayout

－6－
6-2.ConnectionTerminal
（※1）ThecontactinthefigureisforpowerOFFandoperation.
（※2）ThecontactinthefigureisforpowerOFFandnon-operation.
（※3）When usinga2-wiresensor, connectittothe10(+)–20(-)terminals.
Wheninputting ananaloguesignal,connectittothe9(-)–20(+)terminals.
Connecteitheroneofthem.
6-3.Operations ofContactandLEDOperations
※TheON/OFFpointoftheLimitcontactcanbeset by%,where4mAoftheinput signalis0%and20mAis 100%.
※Theoperationof theequipmenterrorcontactis processedinternallybytheequipment.
However,youcansetthepercentagevalueforthesensorerrorcontactoperationsimilarlytotheLimitcontactor
choosetodisableitforcibly.
*1)Thesensorfailureincludes0mAinput(sensorisnotconnected).
Ｌ Ｎ COM NO NC COM NO NC － － ＋ COM NO NC COM NO NC － ＋ ＋
1 2 3 4 5 6 7 8 9 10 20 11 12 13 14 15 16 17 18 19
Name
State No.1Limit (L1) No.2Limit (L2) Devicefailure (FAULT) Sensorfailure*1) (S. Failure)
PowerON
Notinoperating
COM-NC：
Closed
LED turns OFF
COM-NC：
Closed
LED turns OFF
COM-NO：
Closed
LED turns OFF
COM-NO：
Closed
LED turns OFF
PowerON
Inoperating
COM-NO：
Closed
LED turns ON
COM-NO：
Closed
LED turns ON
COM-NC：
Closed
LED turns ON
COM-NC：
Closed
LED turns ON
PowerOFF
COM-NC：
Closed
LED turns OFF
COM-NC：
Closed
LED turns OFF
COM-NC：
Closed
LED turns OFF
COM-NC：
Closed
LED turns OFF
（※1）（※1）（※2）（※2）
Equipmentfailure
Relayoutput Sensorfailure Relayoutput Inputsignal（※3）
10-20：2-wiresensor
9-20：analoguesignal
No.1Limit
Relayoutput No.2Limit
Relayoutput Outputsignal(※4)
17-18：3～24mADC
17-19：0.75～6VDC
Powersource
85～264VAC
Fig.6．Connectiondiagram
LightON
LightOFF LightOFF
State(LED)
State(Contact) Operation Non-operation
LightOFF
Non-
Operation
LightON LightON
State(LED)
State(Contact) Non-operation
Operation Operation
ONpoint
OFFpoint
OFFpoint
ONpoint
Inputsignal Inputsignal
LimitcontactoperationandLEDoperation withlowerlimitsetting
LimitcontactoperationandLEDoperation withupperlimitsetting
Table2
．
C
ontacto
pe
ratingandLEDoperation
Fig.7．LimitcontactandLEDoperation

－7－
6-4.BlockDiagram
2
Ｎ
Relay
7
NC
NO
12
11
COM
Sensorfailure
LED
Powercircuit
COM
F
AULT
Equipmenterror
LED
NC
Relay
NO
Power
LED
COM
Ｌ
1
3
Powersource
Sensorfailure
contact
FAULT
Equipmenterror
contact
Fig.8．Blockdiagram
Voltageoutput
Currentoutput
No.
2
Limit
contact
No.
1
Limi
t
contact
19
18
17
8
13
16
15
14
6
5
4
Analog
Outputcircuit
Isolatedcircuit
Outputsignal
Conditioning circuit
Contact
Outputcircuit
Relay
Relay
No.
2
L
imit
LED
No.
1
Limit
LED
Microcomputer
C
urrent
inputcircuit
LED (Display)
Buttonoperation
249Ω
＋
＋
NC
NO
NC
NO
COM
－
20
10
9
－
＋
－
2
-
wireSensor
C
urrent
input

－8－
７．Start-up
7-1．Warming-upOperationandStart-upFlow
To stabilize the output signal, the equipment needs to be warmed up for at least 10 minutes after
power-on.
Thestart-upflowisshowninFigure9.
M
ounttheconverter
Executethewiring
Checkthewiring
Checkthepowersupply
C
heckthatnoerror
codeisdisplayed
A
djustusingthe
operationbuttons
onthefrontpanel
O
K?
O
K?
O
K?
Startmeasurement
Y
N
Y
N
Y
N
Fig.9．Start-upflow
Turnonthepower
C
heckthatthereisno
problemwithsettingvalues
N
C
hecktheerrorcode
Andsymptom
I
nformourpersons
-
in
-
chargeofthedetails
R
eturnthe
equipment.Etc.

－9－
7-2．LCDScreenandButtonOperational
PerformtheadjustmentontheLCDscreenusingtheoperationbuttonsonthefront panel.
Button Operation
ESC Cancelofsetting Backtotheprevious
menu
+ Selection ofthesetting
valueoritem
▶ Shiftofthesettingvalue
OK Confirmation ofthe
settingvalueoritem
2 5 . 0
%
Operationbuttons
LCDscreen(measuringscreen)
Menudisplay
Unitdisplay
Measurementvalue display
(Scaledisplay)
*Thedisplayedmeasurement
valuecorrespondstotheinput
signal.
Errordisplay
Itemdisplay
Menu
0
▶1.Basicsetting
2.Test
3.Reset
4.Language
5.Deviceinfo.
OK × once
(Menuscreen)
Fig.10.LCDscreenandoperationbuttons