Grundig DIGI 100 User manual

Table of Contents
GENERAL
”Service per mouse click “ ((flash-programming,Digi 100 chassis) .................................................................. e_01/01
AUDIO / HiFi
M 100 CD MK II................................................................................................................................................ e_01/01
CAR AUDIO
Navigation system GPS 3 ................................................................................................................................ e_01/01
DVD
DVD-Player GDV 100D, GDV 100D/002, GDV 110, GDV 200, Xenaro GDP 5100,
GDP 5102, GDP 5120, GDP 6150, Malaga SE 1230 ...................................................................................... e_01/01
SAT
Satellite headend station STC 1880 ................................................................................................................ e_01/01
TV
Colour TV sets wit the chassis Digi Basic 3 - CUC 1832, 1930 and 1931 ....................................................... e_01/01
Flash programming for the new Digi 100 generation ....................................................................................... e_02/01
Special functions (options) for the colour TV sets with the chassis Digi 100 ................................................... e_03/01
Chassis Digi 100 - Flash-Programmer FProg1 ................................................................................................ e_04/01
Chassis CUC 21… - Service Documents ........................................................................................................ e_04/01
Colour TV sets with the chassis CUC 2103 and CUC 2121 ............................................................................ e_05/01
Replacing the memory EEPROMs with the chassis CUC 2103, 2105, 2121, and 2130 ................................. e_07/01
Burned battery socket or battery connecting cable P 37-830/12 and P 37-840/12 SAT, and eqivalent units... e_08/01
Damage to the bottom corners and edges of the TV sets Lenaro MFW 84 - 6110 and MFW 92 - 6110 ......... e_09/01
TV sets with Digi 100 chassis .......................................................................................................................... o_01/01
TP 750/715 and equivalent units...................................................................................................................... o_02/01
ST 70-2103 SAT retrofitting not possible.......................................................................................................... o_03/01

General
Central
After-Sales Service
Service Information
MWLE_0201 (8002/8012_o. DK, F, N, S, SF, P / 8003_MT)
1/2
Serial No. 01/01
”Service per mouse click “ (flash-programming, Digi 100 chassis)
Dear business partner,
For an optimum stationary and mobile product support of our new CTV
models generation fitted with the DIGI 100 chassis, we are able to offer you
the Flash-Programmer F-Prog. 1“. This is a service interface enabling the
dialogue between the CTV terminal unit and a desktop or notebook PC.
With the help of a PC and the Flash-Programmer F-Prog. 1, software updating
can be carried out both in the workshop and on-site at the end user.
This kind of updating guarantees an immediate availability of the current
software. With this TV set type, order/delivery delays as well as the repair
through EPROM updating are a thing of the past. We are sure that this way
of software updating will make its entrance also with future products.
The F-Prog. 1 (material number 759880740000) will be offered at a price of
DM 29.90 (EUR 15.29) plus VAT.
Scope of delivery: Flash programmer (RS232 converter)
RS232 cable (25-to-9-pin)
Diskette (PC software and user manual)
We recommend you to make use of the order option via the Internet.
Of course you may still order the F-Prog. 1 also via the Hotline number
++49 911 93394828 or via email: [email protected].
As registered Grundig reseller you are authorized to access the Grundig
spare parts master record. Please let assign you via the below stated address
your individual password after indicating your customer number:
email: [email protected].
For ordering via the Internet, please follow the instructions below:
- Start the Microsoft Internet xplorer or Netscape Navigator.
- Enter the address: http://www.grundig.com
- Click to Info + Products.
- Position the mouse pointer to Service and click to Reseller Support.
- Click to spare parts: ordering and listings, service documents.
- Login by entering your customer number and password.
- Enter the product number (759880740000) then click to search now.
Note: on this display you will also find the link to downloading the
current device software (spare parts listings and service documents)
- Click to the appearing product number 759880740000.
- Click to put into cart.
- Click to shopping cart in the head bar.
- Click to offer.
- Click to send order.

In cooperation with one of our suppliers we have establisehd for you an offer for a Notebook which,
because of its configuration, is especially appropriate for the on-site updating at the customer.
Manufacturer/ type: Fujitsu-Siemens Liteline 325 A
Features: AMD K6-2 500MHz
64 MB RAM
5.0 GB Hard Drive
12.1" HPA Display 1024 x 768
24x CD-ROM
NiMH accu
56k modem
MS Windows 98 SE
MS Works Suite 2000
12 months bring-in guarantee
Price: DM 2,450.00 plus VAT
EUR 1,252.67 plus VAT
Please place your order directly to :
Grundig AG
Zentralkundendienst
Beuthener Straße 55
D-90471 Nürnberg
Kind regards
Yours
GRUNDIG Central After-Sales Service
Enclosure: Hotline and further contact addresses of the supplier of the PC.

Hotline und weitere Kontaktadressen
Bitte halten Sie vor Ihrem Kontakt mit der PC-Hotline oder mit unseren Servicepartnern immer die Identnr. Ihres Geräts griff-
bereit (siehe Beispiel Typenschild).
PC-Hotline
Bei Fragen oder Problemen hilft Ihnen gerne die PC-Hotline weiter.
Öffnungszeiten Montag bis Freitag von 9.00 – 18.00 und Samstag von 9.00 – 14.00.
Consumer-PC’s (SCENIC Xpert) + 49 (0) 180 / 3 77 70 04 (Tarif DM 0,18/min.)
Notebooks + 49 (0) 180 / 3 77 70 01 (Tarif DM 0,18/min.)
Business-PC’s + 49 (0) 180 / 3 77 70 00 (Tarif DM 0,18/min.)
Workstations + 49 (0) 180 / 3 77 70 03 (Tarif DM 0,18/min.)
Fax: + 49 (0) 821 / 8 04 37 50 (Tarif DM 0,18/min.)
Siemens IT Service Call Management Center
Call Center (Störannahme) Öffnungszeiten durchgehend + 49 (0) 180 / 5 40 40
Fax: + 49 (0) 180 / 5 33 67 79
weitere Kontaktadressen
Die Adressen der Servicepartner finden Sie in dem zu Ihrem Fujitsu Siemens Produkt mitgelieferten Serviceadressheft oder
im Internet, Webseite http://www.fsc-pc.de/Kontakt.asp
auf dem Abruffax Fax: + 49 (0) 821 / 8 04 27 01
in der PC Service Mailbox + 49 (0) 821 / 8 04 33 33 (analog)
+ 49 (0) 821 / 81 40 07 (ISDN)
+ 49 (0) 821 / 8 29 71 (ISDN)
Auch Ihr Vertriebspartner, bei dem Sie das Produkt gekauft haben, gibt Ihnen gerne Auskunft. Für weitere Fragen oder Be-
merkungen bezüglich unserer Garantie, wenden Sie sich bitte an Ihren Vertriebs- oder Servicepartner oder an:
Fujitsu Siemens Computers GmbH
Service Management
D - 86147 Augsburg
Hotline and further Contact Addresses
Please always keep handy the identification no. of the product concerned (see type plate example) before contacting our PC
Hotline or our service partners.
PC Hotline
In the case of questions or problems our PC Hotline personnel will be glad to assist you. Hours of business on Monday
through Friday from 9 to 18 hours and Saturdays from 9 to 14 hours.
Consumer PCs (SCENIC Xpert) +49 (0) 180 / 3 77 70 04 (tariff 0.18 DM/min.)
Notebooks +49 (0) 180 / 3 77 70 01 (tariff 0.18 DM/min.)
Business PCs (SCENIC Xpert) +49 (0) 180 / 3 77 70 00 (tariff 0.18 DM/min.)
Workstations +49 (0) 180 / 3 77 70 03 (tariff 0.18 DM/min.)
Fax: +49 (0) 180 / 3 77 70 04 (tariff 0.18 DM/min.)
Notebooks +49 (0) 821 / 8 04 37 50 (tariff 0.18 DM/min.)
Siemens IT Service Call Management Center
Call Center (failures reception) Round-the-clock hours of business +49 (0) 180 / 5 40 40
Fax: +49 (0) 180 / 5 33 67 79
Further Contact Addresses
The addresses of our service partners are to be found in the service address booklet supplied with your Fujitsu Siemens
product, or
in the Internet, Web page http://www.fsc-pc.de/Kontakt.asp
under the polling Fax No. +49 (0) 821 / 8 04 27 01
in the PC Service Mailbox +49 (0) 821 / 8 04 33 33 (analog)
+49 (0) 821 / 81 40 07 (ISDN)
+49 (0) 821 / 8 29 71 (ISDN)
Your reseller where you have purchased the product will also be glad to provide you with the necessary information. For
further information on our guarantee please contact your sales or service partner, or:
Fujitsu Siemens Computers GmbH
Service Management
D – 86147 Augsburg
8002/12, 8003/13, 8005/15

46161(8002/8012, 8005/8015)
Returns
analysis
Unit:
Service Information
AUDIO / HIFI
Serial no. 1/01
M 100 CD MK II
Possible complaint:
CD’s are at times not read, tracks are not found.
Remedy:
Replacement of the microprocessor CIC 1 carrying the designation
D78P048 AGF M 100 CD with a D78P048 AGF CD-05 MK-II.
Workshop:
In the event of a complaint, replace the microprocessor along with new
software.
Stockkeeping:
CIC 1, D78P048 AGF CD-05 MK-II, part no. 59798 419 0000
1/1

44241000 (9033)
Returns
analisys
Unit:
Service Information
CAR AUDIO
Serial no.
Navigation system GPS 3
Possible complaint:
The colours of the leads to socket 3 (voltage supply) of the cable tree supplied do
possibly not correspond with the information given in the mounting instructions.
Remedy:
Please consult the excerpt of the updated mounting instructions:
Workshop:
Please observe in the event of a complaint.
Stockkeeping:
none
1/1
1/01
ENGLISH
7
CONNECTIONS TO THE CABLE TREE ________________________________________
Socket

:: to ISO plug

of the vehicle (ISO socket)
1white SCV
2green/yellow Mute
3red /white
4clamp 15/30 ignition (clamp 15) red line
5blue Aerial
6orange Illumination
7clamp 15/30 (continuous plus, clamp 30) yellow line
8brown Earth
Connections 3and 5are transferred directly to plug

(for the car radio).
Plug 1: telephone connection (6-pin) GRUNDIG devices since WKC 5300 RDS
11 pink Telephone: AF output
12 black Telephone: earth
When using DAB and a navigation system (to be carried out by a qualified workshop):
Remove plug 1, pins 11 and 12, and insert them into the corresponding plug of the DAB system.
12
11
1 3 5 7
2468
All illustrations show the plug
layout from the rear.

43280100 (8002/8012, 8005/8015)
Returns
analysis
Unit:
Service Information
DVD
Serial no.
DVD-Player GDV 100D, GDV 100D/002, GDV 110, GDV 200,
Xenaro GDP 5100, GDP 5102, GDP 5120, GDP 6150, Malaga SE 1230
1/1
01/01
Controlling the DVD players with the TP 100C, TP 110C and TP 130C TV
remote controls
The basic functions of the above DVD players can be controlled with the TV
remote controls TP 100C, TP 110C and TP 130C.
The DVD players operate with two different remote control codes.
The GDV 100D, GDV 100D/002, GDV 110 and GDV 200 can be controlled
without changing the code.
For controlling the DVD players Xenaro GDP 5100, GDP 5102, GDP 5120,
GDP 6150 and Malaga SE 1230, the remote control code must be changed on
the TV remote controls.
For this, press and hold down the „MODE“ button on the TV remote controls
while pressing the numeric buttons 4, 5 and 6 simultaneously.
To reset the TV remote controls to the factory setting (control of the GDV 100D,
GDV 100D/002, GDV 110 and GDV 200), press and hold down the „MODE“
button on the TV remote controls while pressing the numeric buttons 1, 2 and 3
simultaneously.
When the operating voltage is decreased, the TP 100C, TP 110C and TP 130C
are also restored to the factory setting. For controlling the DVD players Xenaro
GDP 5100, GDP 5102, GDP 5120, GDP 6150 and Malaga SE 1230, the remote
control code must be set again when the battery is replaced.
Stockkeeping:
Telepilot TP 100C (gray) Part no. 296420614102
Telepilot TP 100C (black) Part no. 296420614600
Telepilot TP 110C Part no. 296420614202
Telepilot TP 130C Part no. 296420614400

SAT
Service Information
Returns
analysis
4119100000 (8002/8012, 8005/8015) 1/1
Serial no. 1/01
Satellite headend station STC 1880
Possible complaint:
Complete failure of the headend station. The fuse Si 60002 T1 AL, and partly
the fuse Si 60020 T2,5 AL, are broken.
Cause:
Short circuit in the power supply transistor T 60006 (IRF PC 50).
Remedy:
In addition to replacing the power supply transistor, replace the diode D60006
MUR 480 with a wire bridge. This measure reduces the drain voltage and with
that the danger of a damage by overvoltage.
Workshop:
In the event of a failure of the power supply transistor, carry out the change.
In addition, carry out this change as a preventive measure on all STC 1880
which are in the workshop, without regard of the existing failure.
Stockkeeping:
Transistor IRF PC 50 Part no. 830280505000
Fuse T1 AL Part no. 831561700400
Fuse T2,5 AL Part no. 831561700600

TV
Returns
analysis
Service Information
4116100000 (8002/8012, 8005/8015) 1/1
Serial no. 1/01
Colour TV sets wit the chassis Digi Basic 3 - CUC 1832, 1930 and 1931
e.g.: Sydney SE 720 Dolby, Xentia M 72-400 Dolby, Denver SE 8250/8 PIP/
Dolby
Possible complaint:
No picture, no sound.
Cause:
Failure of the power supply transistor T 60006 (IRF PC50 or 2SK2699).
Remedy:
In addition to replacing the power supply transistor change the SMD
capacitor CC 60014 from 3.3 nF to 10 nF. This results in a better softstart
function of the power supply.
Workshop:
In the event of a defective power supply transistor replace in addition the
capacitor.
Stockkeeping:
SMD capacitor 10 nF 0805 Part no. 867219817300
Transistor IRF PC 50/2SK2699 Part no. 830280505000

420710000 (8002/8012, 8005/8015)
Returns
analysis
Gerät:
Service Information
TV
Serial no. 02/01
Colour TV sets Digi 100
Flash programming for the new Digi 100 generation
For the above stated series of sets, no completely programmed EPROM has
been used for the device software.The software is stored in a Flash-Eprom that
can be externally loaded. In this way it is possible to update the software with-
out opening the housing of the TV set.
To do this, the new software is downloaded into the TV set via the serial inter-
face of a PC and the programming socket located at the rear of the TV set using
a download programme and a RS232 converter (Flash-Programmer F-Prog 1).
Required equipment
Flash-Programmer F-Prog 1, part no. 759880740000
Required hardware (minimum)
- PC with processor 486/66 and operating system Windows Version 3.11 or
higher
- 8 MB free main memory
- Free fixed disk capacity of 20 MB
- Internet access or InfoTip-System
Calling up the current device software
The software can be called up from a protected area of the Grundig Internet
Homepage after entering your customer number and a password, or it can be
called up via the InfoTip-System (under „Service Tips“).
Example for calling up the software from the Internet:
- Start the Microsoft Internet Explorer or Netscape Navigator.
- Enter http://www.grundig.com and confirm.
- Click to Info + Products on the Grundig Home-Page.
- Position the mouse pointer to Service.
- Click to Reseller Support.
1/1

Note: In the retailer support menu, you may applicate for access by entering
your customer number and your address.
- Click to spare parts: ordering and listings, service documents.
- Enter your custumer number and password.
2/3
- Click to login.
- Click to spare parts lists and service documents.

Service Information TV 02/01
- Select the desired software under software download.
- Copy the selected device software into the folder
C:\GRUNDIG\Software of
your PC which has been created when installing the F-Prog 1-PC software.
3/3
The downloaded packed file (*.zip) then must be unpacked by an appropriate
unpacker for „ZIP“files (appropriate unpackers can be found, for example,
under www.winzip.com).
ZIP files cannot directly be loaded into the TV set!
Additional hints/particularities for programming with the „F-PROG 1“:
- Before connecting the Flash Programmer, switch the TV set off with its
mains button then connect the programmer when the operating LED
has gone out!
- After starting programming, the operating LED first remains dark then
starts flashing as soon as the Flash memory is deleted.

TV
Service Information
Returns
analysis
4121100000 (8002/8012, 8005/8015)
1/2
Serial no. 3/01
Setting hints and special functions (options) for the colour TV sets with
the chassis Digi 100 (CUC 1807, 1837, 1838, 1839, 1934, 1935)
e.g.: Elegance 70 M 70-300 Dolby, Elegance 70 MW 70-150/8 Dolby,
Hamburg SE 8240 Dolby, M84-212/8 Dolby, Toronto SE 7216 Dolby
Below you find setting hints and explanations for various functions of the TV
sets with the chassis Digi 100.
1. Power-on behaviour of the set
In the „Special functions“ menu you can select under the „Power on“ menu
item between „automatic“ and „Programme position 1“ .
automatic: the set is switched on with the last power-on mode. For this, the
last recognized programme position and operating mode (standby or
normal operating mode) are stored.
Note: if the set has been switched off with the mains button in standby
mode, it goes again in standby mode after power on and must
definitely be switched on using the remote control.
Programme position 1: the set selects programme position 1 each time it is
switched on.
2. Settings in the „Programme table“ menu
In this menu, further presettings can be programmed in addition to the
channel setting for every programme position.
Note: direct channel entry is only possible in the programme table.
„P+“ reversion point: the reversion point is the limitation of the programme
positions for programme selection using the „P+“ button. This
reversion point is marked with an orange line in the programme table.
To shift the reversion point, it is necessary to shift the programme
position above or below this line according to the direction of shift.
1-/2-/3- digit programme position selection (3-digit only with a retrofitted
satellite module): for 1-digit programme position selection you must
place the reversion point in the programme table between the
programme positions 1 and 10. For 2-digit programme position
selection place the reversion point between the positions 10 and 100.
Forced settings (forced colour standard, forced mono, fixed assignment of a
multi-channel sound, RF time constant, AFC):
In the „Channel settings“ menu (menu guide: „i“ -> „Programme table“
-> „Edit“ -> „Change channel settings“) you can carry out various
forced settings.
Note: it is also possible to set a forced colour standard for the AV
programme positions in this menu.

2/2
Service Information TV 03/01
3. Volume adjustment:
You can store a volume setting deviating from the basic volume separately for every
programme position in the „Sound“ menu (blue button) under the menu item „Volume
adjustment“. This adjustment is allowed by the software only if the basic volume is higher than
7 of the 64 steps of the control range.
4. Picture settings (brightness, contrast, colour, etc.):
The desired picture settings are carried out in the „Picture“ menu (red button). Changing the
contrast is only possible with the „manual“ presetting. The presettings „During the day“ and „In
the evening“ are stored with fixed contrast settings. To get a better overview, it is possible to
reduce the large menu scale after selecting the desired menu item by pressing the „OK“
button. In doing so, more menu content is visible and the setting, e.g. colour contrast, is highly
facilitated.
5. Sat radio (only with satellite retrofit kit SER 300A):
Via the menu guide „i“ -> „Infothek“ -> „Sat-Radio“, about 40 pre-stored sat radio stations can
be called up (dark picture screen, only the station name is visible). In this operating mode, the
programme table can be displayed after pressing the „i“ button in order to select/change the
sat radio stations.
6. Time and date:
Each time the set is powered on, the internal software clock is set when receiving a station
broadcasting Teletext.
If only stations without Teletext are received after power on, no clock time can be called up. In
this case, the clock and time can manually be set via „i“ -> „Installation“ -> „Time and date“.
7. AV settings:
The sets with the chassis Digi 100 provide the possibility of individually configuring all
available AV programme positions. The factory settings are:
AV 1 for the connection of a Megalogic video recorder,
AV 2 for the connection of a DVD player (via RGB),
AV 3 (if available) for the connection of a VHS video recorder (a switching voltage is
necessary at the Euro-AV socket Pin 8),
AV 4 for the connection of a VHS camera.
If you wish to change these presettings, you can individually configure all AV connections via
„i“ -> „Installation“ -> „Connections“ . In this menu, various units are preset which can be
activated if they are required. A connection diagram can be displayed by pressing the yellow
button.
In addition own unit profiles can be created via the menu item „Manual AV settings“. These
unit profiles are indicated with „manual“ in the connection diagram. Please note that settings in
the „Manual AV settings“ must correctly be effected in any case, and that preset units at AV 1,
AV 2 etc. are deactivated at the same time (see connection diagram). For example, an
incorrectly set time constant would result in a black/white picture with a VCR signal source.

TV
Returns
analysis
Service Information
E-BS-SA_2801 (8002/8012, 8005/8015) Subject to alteration 1/2
Serial no. 04/01
1. Chassis Digi 100 - Flash-Programmer FProg1
Additional function through software change (version 1.1)
After replacing the Feature module, the unit-specific settings like colour
registration, noise reduction, picture sharpness, white balance, CRT type, PIP
position, picture geometry, and the customer-specific programme data must be
set up.
The extension of the FProg1 software now makes it possible to read out this data
and to write it into the new module.
This means a considerable decrease of expenditure of work.
For reading out and programming the operating software and the unit-specific data
you need the Flashprogrammer FProg1, part no. 759880740000. Please consult for
this also the Service Information ”General, serial no. 01/01“.
The Flash-Programmer comes with the software version 1.0. Please load the current
software, version 1.1, directly from the Internet (see Online Service brochure). This
is to be found under “Reseller Support“, “Software Download“ in the category
”Programming software“, Product group ”DIGI 100”. The updated description of
the FProg1, V1.1 software is to be found under Advice ”Operating instructions Flash-
Programmer F-Prog1“.
Stockkeeping: Flash-Programmer FProg1, part no. 759880740000.
1. Chassis Digi 100 - Flash-Programmer FProg1,
2. Chassis CUC 21… - Service Documents

2/2
2. Chassis CUC 21… - Service Documents
Service Manual 720100407000
Service Manual, 1st supplement 720100407100
Dear business partner,
despite multiple checks of the printing data we are not immune against
printing errors. For this reason please correct the above documents
according to the following information.
• Service Manual 720100407000
The following alignment points replace the corresponding alignment
points in the Service Manual, page 2-1.
The following oscillogram ´E replaces the oscillogram 78 on page 3-26
(CRT plate) of the Service Manual.
´E
• Service Manual, 1st supplement 720100407100
The following hint replaces the corresponding hint on page 3.
Software version number
Press the "Ǻ" button to call up the "DIALOG CENTER" menu –> OK.
Press "AUX" to display the software version number.
Adjust 300mVpp with button Ǹor Ƿ.
Terminate the dialog line "End" "with mem" –> "OK".
Use the UG2 control (splitter transformer) to adjust at the
test point having the highest voltage potential a voltage of
112.5V ±2.5V for 14" picture tubes, and a voltage of 150V
±2.5V for 15"...21" picture tubes.
2. Tuner AGC
8. Screen grid
voltage UG2
100MHz oscilloscope: Channel A: Tuner contact 10 or 11.
Ground: Tuner
Colourvideo generator:Feed ina colourscale (withswitched-
off sound carrier) via the aerial,
≥80dBµV.
Call up the dialog line "AGC" via "Ǻ" (Dialog Center) –>
Service –> "OK" –> Service Code "8500".
Colour video generator: Feed in a black test pattern.
Adjust the screen brightness so
thatthe testpattern justturnsdark.
High-resistance volt-
meter via 220KΩ: Test points R, G, B
(picture tube plate).
Determine the test point having the highest voltage.
Alignment Preparations Alignment Process

TV
Returns
analysis
Service Information
4128100000 (8002/8012, 8005/8015) 1/1
Serial no. 5/01
Colour TV sets with the chassis CUC 2103 and CUC 2121
e.g.: P 37-4101 TOP Davio, T 55-4101 TOP Davio, T 55-4104 TOP Lemaxx
Listed below are the unit types on which the option of retrofitting a satellite
retrofit kit SER 2100 has been omitted. In the new GRUNDIG main
catalogue, this is not considered in the technical data. In order to distinguish
the retrofit option, the version marking at the rear panel has been changed
from „VNM“ (retrofitable) into „VNA“ (not retrofitable).
The following unit types are concerned::
CUC 2103 CUC 2121
Arcance 37 P 37-2101 MV Davio 55 ST 55-854/8 Dolby
Davio 37 P 37-4101 TOP Greenville SE 5592 MV/Dolby
Davio 37 P 37-4101 TOP/1 Leemaxx 55 ST 55-4105 MV/Dolby
Davio 37 P 37-4101 TOP/TR ST 55-839/8 Dolby
Davio 37 P 37-4101 GB ST 55-908/8 Dolby
P 45-4101 TOP ST 55-908/8 FR/Dolby
P 45-4101 MV/TOP Xentia 55 ST 55-405/8 Dolby
Arcance 51 T 51-2101 MV
Davio 51 T 51-3101 TOP The units
Davio 51 T 51-3101 TOP/1 ST 55-734 GB/Dolby and
Davio 51 T 51-3101 TOP/TR ST 55-934 GB/Dolby can be
Davio 51 T 51-3101 MV retrofitted with the„VNM“
Arcance 55 T 55-2101 MV and „VNA“marking. With the
Davio 55 T 55-4101 GB „VNX“marking the retrofit
Davio 55 T 55-4101 MV option is omitted.
Davio 55 T 55-4101 TOP
Davio 55 T 55-4101 TOP/1
Davio 55 T 55-4101 TOP/TR
Leemaxx 55 T 55-4104 TOP
S 55-806 TOP/TR
Workshop:
On a small number of the Davio 37 P 37-4101 TOP sets with the version
identification „VNM“(retrofitable), the processor has not been fitted with a
socket but has directly been soldered in. So that the processor board can be
fitted in the event of a SAT retrofitting, you must solder in an IC socket in
place of the soldered-in processor.
Stockkeeping:
IC socket, 56-pin Part no. 813090012900

TV
Returns
analysis
Service Information
4130100000 (8002/8012, 8005/8015) 1/1
Serial no. 7/01
Necessary settings after replacing the memory EEPROMs for colour TV
sets with the chassis CUC 2103, 2105, 2121, and 2130
e.g.: P 37-4101 TOP Davio, T 55-4101 TOP Davio, T 55-4104 TOP Leemaxx,
ST 55-854/8 Dolby
Possible complaint:
After replacing the EEPROM CIC82501 (M24C08) the set is not fully operati-
ve despite of loading the emergency data set. Especially the teletext function
is restricted.
Workshop:
The following settings must be carried out after fitting a new EEPROM
M24C08.
Note: it is absolutely necessary to keep the order of the first two points to
gurantee the proper functioning of the teletext!
Stockkeeping:
SMD IC M24C08 Part no. 830596000800
1. Loading the configuration
data for the teletext decoder.
2. Loading the emergency
data set.
3. Setting the menu colours.
4. Geometry, white balance,
AFC, and AGC alignment.
5. Configuration of the
Euro-AV socket „AV 1“
Switch the set on with the mains switch then
switch it off again when the picture appears on
the screen.
Note: the menu display is shifted to the left!
Press and hold down the „P-“ button on the
remote control while switching the set on with
the mains switch.
Set the menu item „OEM“ in the Service menu
(access with the code „8500“) to „off“.
Carry out these settings according to the
Service Manual.
In the „AV 1“ programme position you can
select between „VHS“ and „SVHS“ under the
„Video“ menu item in the „Special Functions“
menu.

TV
Service Information
1
Number: E/08/01; e_tv081e
TQ42_4101 (Online, 8002, 8012, 8005, 8015)
Possible complaint:
Failure of the 12V power supply due to burned battery sockets or battery
connecting cables.
Cause :
Contact resistance between the battery socket and the plug of the battery
connecting cable.
Remedy:
To ensure the proper fitting accuracy, the battery socket must be replaced along
with the battery connecting cable with the new version.
Stockkeeping:
Battery connection set FFS (battery socket and battery connecting cable).
Part no. 759550410700
Alterations reserved.
Burned battery socket or battery connecting cable
P 37-830/12 and P 37-840/12 SAT, and eqivalent units