Maxair CAPR 2271PB-07SM User manual

P/N 07823145 Rev D Page 1
2271PB-07 Hood
Instructions For Use
WARNING
Use only if package is received unopened and contents are
undamaged. If damage is noted, contact the shipper for replacement
or repair.
Prior to using any MAXAIR®System or component, be sure to be
familiar with the system’s NIOSH approved conguration.
DO NOT use if any component is damaged. If any components are
damaged or contaminated and therefore unt for safe and e󰀨ective
use, they should be replaced immediately.
Only trained and experienced personnel who have read and under-
stand the User’s Instructions should use this product.
Failure to follow the User’s Instructions, these and in the MAXAIR
Systems User’s Instructions, P/N 03521015, may be hazardous to
the user’s health.
The institution using this product in any application is responsible for
determining the appropriateness of this equipment relative to regula-
tory requirements. Bio-Medical Devices Intl, Inc. does not recom-
mend the appropriate systems for a particular institution or facility.
Use only MAXAIR Systems/ NIOSH approved compatible
components.
NOT for use in atmospheres immediately dangerous to life or health
(IDLH), and atmospheres containing less than 19.5% oxygen, or
more than 25% oxygen.
Flammability Level I: fabric may burn if exposed to open ame.
Follow current local regulations governing biohazard waste to safely
dispose of used shrouds.
If you need more information, contact your BMDI Sales
Representative, or call BMDI customer service at 1-800-443-3842.
CAUTION
Before use, refer to the CAPR®User’s Instructions, P/N 03521015 (received with all CAPR Helmets) for details.
!
Symbol Denitions
Warning, Caution, or Note Order Number
!
!
Intended Use
The MAXAIR®CAPR® Hood Systems are intended to lter
aerosolized and droplet particulates and provide high level uid
resistance.
Hoods are designed for single use applications.
Hood Specications
Temperature Limits: 490C maximum
Materials:
Regulatory
NIOSH
Typical Hood System Components
1 The 2500-30TSC is an alternate to the 2500-37TSC.
MATERIAL TYPE FLUID RESISTANCE
Body (Shroud) Polypropylene ASTM F1671
Lens Polycarbonate ASTM F1671
Hood Filter Polypropylene AATCC TM127
HLF Polypropylene/
modacrylic blend
General particle lter
material
O.N.
1. 2081-03 Helmet 2. 2271PB-07 Hood w/2170-27 HLF
3. 2061-05 HFR FCC 4. 2500-37TSC Battery1
5. 2000-76 Battery Belt 6. 2600-01 Battery Charger
12 3
4 5 6
O.N. 2271PB-07SM
(Small-Medium)
P/N 07831155
O.N. 2271PB-07ML
(Medium-Large)
P/N 07831156
*one 2170-27 (07831205) HLF is
included with each Hood

Page 2 P/N 07823145 Rev D
2271PB-07 Hood
Instructions For Use
Don Battery, Belt, Helmet and Hood
1. Remove all System Components from their packaging, ensure they are ready for use, and lay them on a clean counter with labels facing you.
5. Attach (snap) one side
Hood-Lens mounting
hole to respective Hel-
met side mounting post.
Repeat on other side.
3. Attach (snap) center
Hood-Lens mounting
hole over Helmet cen-
ter mounting post.
6. Grasp the back of the
Hood Filter and begin
to pull the Hood up and
over the Helmet.
2. Assemble the Battery onto a double layer of Belt. Place
top edge of Belt under the Battery Clip, up to the Clip
top, so the Clip Detent rests on the Clip Base and NOT
the Belt. Place the belt comfortably around the waist
with the battery near the side-back of the right hip.
7. Continue pulling the Hood
over the Helmet down to
within about 1-2 inches from
the top rear Helmet Snap.
10. Ensure the Cu󰀨 Flap-
pers are away from the
Lens and in front of the
Liner Side Tabs.
4. Gently pull Cu󰀨 and
Flappers away from
Lens to ensure they are
not stuck together.
8. If the Hood Filter if folded over the front
Velcro Strip, “ip” the fold up to expose
the Velcro Strip. Pull the Hood down fur-
ther in back to remove the wrinkles from
the Hood Filter over the Helmet top.
9. Connect Helmet Power Cord
to Battery. Push Power
Cord Connector into Battery
Receptacle until Secure
Connection audibly clicks.
13. Slide ngers between Cu󰀨
and face from temples down
and under chin to pull Cu󰀨
Flappers away from Lens, and
to properly position the Cu󰀨.
11. Loosen the ratchet
adjustment knob
counter-clockwise to
ensure the Helmet will
easily t over the head.
12. Hold the Helmet in one hand, pull
the front top edge of the Cu󰀨 down,
and place your chin into the Cu󰀨.
Then, pull the Helmet over and
down on to your head.
WARNING
If conditions 1 and 2 both are not achieved, switch to other size DLC and repeat Assembly and Donning steps 1-13.
Condion 1: Ensure the DLC Flappers are away from
the Lens, posioned perpendicular to your temples,
and in front of the FCC Side Tabs.
Condion 2: Ensure slight tension is felt while sliding the
index or rst nger between cu and face all along chin and
up to temples, from right side of the face to the le.
DLC Flappers
FCC Side Tabs

Page 3 P/N 07823145 Rev D
2271PB-07 Hood
Instructions For Use
2. Either continue grasping the HLF and lift it up, over, and o󰀨 the
Helmet and discard appropriately, or ALTERNATIVELY,
you may temporarily leave it on the Hood and proceed to Do󰀨 it
with the Hood (next section).
1. Begin HLF do󰀩ng by curling its back bottom up over Helmet
back bottom.
Do󰀨 HLF
Don HFR FCC (Optional, depending upon uid resistance protection desired.)
3. Ensure HFR FCC is down to or below all
around bottom edge of Hood Filter.
1. Initiate donning the HFR FCC (High Fluid Resis-
tant Filter Cover Cap) by placing it over the front
of the Helmet and down towards the back.
2. Continue bringing the HFR
FCC down over the Helmet
so that it covers the HLF.
1. Hold front of HFR FCC in
place while lifting its rear
up over Helmet.
Do󰀨 HFR FCC (If it was Donned)
2. Remove HFR FCC com-
pletely and decon for next
use.
Don HLF (NOT optional - Required per NIOSH Approval)
3. Ensure Hood Skirt is fully down on all
sides, secure neck ties to within about 1/2
inch of neck, and feed body ties through
front hood shroud slits and tie securely.
1. Initiate donning the HLF
(Heavy Loading Filter) by
tucking its back bottom up
under back bottom of Helmet
2. Complete by pulling HLF over and down, rear-to-
front, of the Helmet and secure front bottom on
Hood front Velcro strip.
16. Don appropriate body gown per
gown manufacturer’s protocol. Keep
Hood Shroud up while closing gown
so Hood is outside of gown.
15. Pull Hood Shroud
down all around.
14. Tighten Ratchet Knob (clockwise) as tight as
possible without causing discomfort to secure
Helmet on head for all anticipated activities.

P/N 07823145 Rev D Page 4
2271PB-07 Hood
Instructions For Use
Do󰀨 the Hood, Helmet, Battery and Belt and outer gown
1. Untie both neck and
body Ties, pull through
their loops and discard
appropriately.
7. Connect a powered on Battery
Charger connector to the Battery.
Push connector into Battery recep-
tacle fully - Do NOT push down on
the Battery Secure Lock (Black)
button.
2. Roll up Hood from Shroud back bottom up
and over to top front of Helmet.
4. With Hood com-
pletely o󰀨 Helmet
discard appropri-
ately.
6. Disconnect the Helmet
Power Cord from the Bat-
tery - Press down on the
Secure Lock (Black) Button
to release, then pull the cord
connector out from the Bat-
tery connection receptacle.
5. Unbuckle Belt and
remove Battery and
Belt from around the
waste.
WARNING
Refer to Secon 9,User’s Instrucons (/PN 03521015:
Charger, for details on proper use of chargers and for
charging baeries.
3. Unsnap each side Flapper
and continue moving rolled
Hood forward and o󰀨 front
Helmet Mounting Post.
6. Loosen the rear Headband
Adjustment Knob (turn
counterclockwise).
5. Do󰀨 body
gown per gown
manufacturer’s
protocol and
discard appro-
priately.
7. Li Helmet up and o
head.