MaxiTrack Sensors InTransit-2 User manual

I n T r a n s i t - 2
I N S T R U C T I O N M A N U A L
NEW GENERATION OF SINGLE USE
TEMPERATURE RECORDER
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

I n T r a n s i t - 2
MaxiTrack Sensors
I M P O R T A N T :
T H E I N T R A N S I T - 2 L I N E L E A V E T H E F A C T O R Y A L R E A D Y
C O N F I G U R E D F O R 6 0 - D A Y T R I P S . T H E D A T A U P D A T E O N T H E
P O R T A L O C C U R S E V E R Y 6 0 M I N U T E S A N D T H E
T E M P E R A T U R E R E C O R D I N G I N T E R V A L I N M E M O R Y , E V E R Y 1 0
M I N U T E S .
A N Y C H A N G E S T O T H E I N I T I A L F A C T O R Y S E T T I N G S M A Y
I M P A C T T H E L O G G E R ' S I N T E R N A L B A T T E R Y L I F E A N D A L S O
T R A V E L A U T O N O M Y .
[email protected] | www.maxitracksensors.com

Press the "STOP" button
continues for 4 seconds, until the red and blue Led lights up. This
signal indicates that the equipment has started operating. During the
first 30 minutes (START DELAY period) the Blue Led will flash every
10 seconds. The device will start Temperature recordings after the
initial 30 minute period.
I N S T R U C T I O N S F O R U S E
START1.
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

Temperature Recording Interval
MIN and MAX alarms
Geo-positioning Alarms
Among others
Through the WEB platform "Galileo Sensors' the user can fill in the
configuration parameters. Through the 'Device Configuration' tab it
is possible to configure parameters such as:
2. SETTINGS
I N S T R U C T I O N S F O R U S E
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

Once activated and configured, place the Data Logger In Transit in
its packaging, thermal box or environment before starting the
transport cycle.
3. TRANSPORT
I N S T R U C T I O N S F O R U S E
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

Reporting Interval ’(sync
interval to the cloud): 60
minutes.
'Recording Interval':
Temperature recording
interval in memory: 10
minutes
For the equipment to work
for 60 days continuously,
configure:
The InTransit-2 technology works with 2 / 3G data transmission
that enables Temperature monitoring and also the
Geopositioningo of the vehicle
Notifications (Alarms) can be sent by email and / or SMS to the
users involved.
4. MONITORING
I N S T R U C T I O N S F O R U S E
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

1 - Press the "STOP" button (during 4
seconds) until the LED Red and Blue ascend.
.
2 - Through the Galileo Sensors Portal, finish
the recordings. After clicking on the END
button and after the synchronization interval
has elapsed, the Data Logger will be stopped.
I N S T R U C T I O N S F O R U S E
5. STOP
Two ways to end the operation of the Data Logger and retrieve
reports.
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

I N S T R U C T I O N S F O R U S E
6. Graphical Reports
Through the Galileo Sensors Portal, select the desired period and
issue Graphical Reports of the entire transport cycle, identified by
the equipment ID.
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

If the data is not updated within the expected period, it is
possible that it is in airplane mode or in a location with no 2 or
3 G signal.
Use this equipment in locations with Temperatures consistent
with its Measurement Range.
Avoid vibration or shock near the device's body.
Do not disassemble the In Transit-2 recorder.
Keep the InTransit-2 recorder away from water, fire or any
hostile environment that may impair its operation.
Please read the information below carefully before using the
equipment:
C A R E
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

Maxitrack is responsible for any manufacturing defects in its
products or instruments, for a period of 12 (TWELVE) months from
the date of acquisition / issue of the NF.
If necessary, request replacement or repair from the commercial
establishment where the product was purchased.
The guarantee will only be valid upon presentation of the purchase
invoice.
In case there is a need to send the equipment to our Laboratory
for possible checks, the forward and return freight is the sole
responsibility of the customer.
This Warranty does not cover any damage caused by the customer,
loss of Temperature data or any other damage related to local
Software or Equipment.
To see our line of Temperature and Relative Humidity Monitoring
via the Internet, with alarms via e-mail and Cellular, access:
G U A R A N T E E C E R T I F I C A T E
www.maxitrack.sensors.com
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com

For reasons of improving the technology used in the manufacture of
our product line, this manual may change without prior notice.
MaxiTrack Sensors
[email protected] | www.maxitracksensors.com