MAXNOMIC MIGSeries User manual

ASSEMBLY INSTRUCTIONS

X
7
Thank you for buying an
original MAXNOMIC®chair!
You have chosen a high-quality
product and we do hope you‘ll
enjoy your MAXNOMIC®MIG chair
for many years to come!
Please follow these instructions
carefully and mind the important
safety advice to make the
assembly of your chair as easy
as possible.
Dear customer,
Before you start:
Please note that the chair shown in the
photos might be a dierent model than the
one you purchased. However, the
assembly instructions are the same for all
MIG models.
As you remove your chair from the box you
may notice slight wrinkles or dents in the
upholstery that have been caused by tight
packing. However, these wrinkles / dents will
usually disappear after a few days, especially
when you start using your chair.
Make sure you have enough space to unpack
the items and organize all of the pieces.
A second person to help you during assembly
is ideal!

Dear customer,
Set the armrests to their highest position to
remove all other parts from the box.
Remove all parts from the box and use the foam packing
material to protect your oor (and the seat parts).
Position the plastic cover AND the joint bracket
as shown in the picture.
CONTENTS: 1x Headrest, 1x Star Base, 5x Wheels,
2x Joint Brackets, 2x Side Covers, 1x Tilt Mechanism,
1x Gas Spring, 1x Telescopic Cover (Gas Spring),
2x Plastic Levers, 1x Glove, 1x Grease,
1x Multitool, 2x Metal Screws
Remove the pre-assembled M8 screws from the
sitting element.
Repeat this with all four screws and tighten them
properly with the provided tool.
1 2
3 4
5 6

Assemble both covers using the
provided metal screws.
Repeat this on the other side of the backrest.
Place the backrest carefully between both
joint brackets of the sitting element.
Use the provided multitool to remove the
screws from the backrest.
IMPORTANT:
Use the side lever to adjust the joint bracket of the
sitting element into a vertical position.
Start the next step on the side with the xed
joint bracket.
7 8
9 10
11 12

Tighten the prepared screws by hand.
Start with the screws at the top, then proceed
to tighten the screws below.
DO NOT TIGHTEN TOO MUCH!
The covers are only meant for the looks of your chair. If
you tighten them too much, they might get damaged.
Tighten the screws in the backrest using the
provided tool.
Insert the screws and tighten the side covers carefully
with slight pressure using the provided multitool.
Adjust the backrest to the rearmost
position using the side lever.
13 14
15 16
17 18

Turn the chair around. Use the foam packing
material to protect your oor and the seat.
Place the tilt mechanism on the threaded holes as shown
in the picture. The control knob for the tilt resistance
points to the front of the sitting element.
Put the telescopic cover over the gas spring as
shown in the picture.
Remove the pre-assembled screws using the
provided multitool.
Tighten the M8 screws diagonally.
There should be 4-5 cm of the gas spring poking
out of the cover.
19 20
21 22
23 24

Lubricate the opening for the gas spring with the
provided grease. It facilitates the assembly and
reduces possible moving noises later on.
Lubricate the bars for the plastic levers with the
provided grease.
Once both levers are in the correct position,
push them tightly.
Put the gas spring incl. telescopic cover in the
destined opening of the tilt mechanism.
Push the plastic handles over the bars of the tilt
mechanism. The at ends should be pointing to the
front of the sitting element on both sides.
Almost done! The headrest, star base and wheels
should be left.
25 26
27 28
29 30

Take the star base and wheels.
Turn the star base around and insert the
wheels one by one.
Place the star base onto the gas spring and rmly
press it into place.
Lubricate the top part of the wheels with the provided
grease. They will be easier to insert then.
Lubricate the opening of the star base with
the provided grease then.
Pick up the chair with one hand holding the sitting
element and the other holding the backrest.
A second person to help you is ideal.
31 32
33 34
35 36

Now you can adjust your chair ...
Sit down on the chair to connect the gas spring
with the star base.
... and push it down until it clicks into
place at least once.
... using the side lever to set the backrest
to an upright position.
Place the headrest over the two designated holes ...
Well done!
We hope you‘ll enjoy your new MAXNOMIC®seat!
37 38
39 40
41 42

Remove the check screw from the bracket as
shown in the picture.
... you have now extended the backrest tilt angle.
Without the check screw ...
Put the side cover back on and tighten
the screw carefully. You‘re done!
REMOVAL OF THE
CHECK SCREW
... to extend the
backrest tilt angle. Remove the bracket side covers using the
provided multitool.
OPTIONAL – In case you’d like to extend the angle of the backrest: