Maxwell AutoAnchor 710-6 User manual
1
AutoAnchor 710-6 Owner’s Manual
Part 1 Important Information 2
Part 2 Installation 5
Part 3 Set Up 18
Part 4 Operation 35
Part 5 Maintenance 45
Part 6 Troubleshooting 46
Index
TABLE OF CONTENTS
To the best of our knowledge the information in this manual was correct at the time
of printing. However, the AutoAnchor products are continuously being reviewed and
LPSURYHGDQGSURGXFWVSHFL¿FDWLRQVPD\EHFKDQJHGZLWKRXWQRWLFH7KHODWHVWSURGXFW
VSHFL¿FDWLRQVPD\QRWEHUHÀHFWHGLQWKLVYHUVLRQRIWKHPDQXDO7KHGRFXPHQWDWLRQ
relating to the AutoAnchor products is created in the English language and may be
WUDQVODWHGIURP(QJOLVKWRDQRWKHUODQJXDJH,QWKHHYHQWRIDQ\FRQÀLFWEHWZHHQ
WUDQVODWHGGRFXPHQWVWKH(QJOLVKODQJXDJHYHUVLRQZLOOEHWKHRI¿FLDOYHUVLRQ
AutoAnchor documents are available on the website www.autoanchor.co.nz
2
7KH$$VKRXOGRQO\EHLQVWDOOHGE\DTXDOL¿HGPDULQHHOHFWULFLDQ'RQRW
DWWHPSWWRLQVWDOOWKH$$XQOHVV\RXDUHVXLWDEO\TXDOL¿HG
7KLVPDQXDOVXSSRUWVWKHXVHRIWKH$$RQO\7KHDSSURSULDWHPDQXIDFWXUHU¶V
LQVWUXFWLRQVPXVWEHIROORZHGIRUWKHLQVWDOODWLRQDQGXVHRIWKHHTXLSPHQWWKH
$$LVVHWXSWRFRQWURO
7KHUHPXVWEHDQDOWHUQDWLYHPHWKRGDYDLODEOHWRRSHUDWHWKHZLQGODVVWKUXVWHURU
RWKHUHTXLSPHQW$IDLOXUHRIWKHZLUHOHVVOLQNZLOOUHVXOWLQORVVRIFRQWURORIWKH
HTXLSPHQWYLDWKH$$
7KH$$FDQEH¿WWHGWRPRVWYHUWLFDOZLQGODVVHV$KRUL]RQWDOZLQGODVVPD\
UHTXLUHDVHQVRUKROGHURUDFXVWRPGHVLJQHGVHQVRUZKLFKLVQRWLQFOXGHGLQWKH
standard pack. Check with your supplier or the AutoAnchor manufacturer.
)RUFKDLQFRXQWLQJWKH$$PXVWEH¿WWHGWRDZLQGODVVZLWKDGXDOGLUHFWLRQ
control box or solenoid pack.
$OOR\VWHHORUFDUERQ¿EUHZLOOUHVWULFWWKHZLUHOHVVFRPPXQLFDWLRQ7KH$$
EDVHVWDWLRQPXVWEHSRVLWLRQHGWRDYRLGWKLVRUDQDQWHQQDFDQEH¿WWHG
Contact your supplier or the AutoAnchor manufacturer for options.
,QIRUPDWLRQIRULQVWDOODWLRQDQGRSHUDWLRQRIWKH$$LVVXSSOLHGLQFOXGLQJ
SUHVHWZLQGODVVSUR¿OHOLVWVZLULQJGLDJUDPVWKH2ZQHU¶V0DQXDODQG
the Quick User Guide. All documents must be left on board for the owner.
1RQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVFRXOGLPSDLURSHUDWLRQRIWKH$$WKH
ZLQGODVVWKUXVWHURURWKHUHTXLSPHQWDQGFRXOGUHVXOWLQSHUVRQDOLQMXU\DQGRU
damage to the boat.
1RQFRPSOLDQFHZLWKWKHLQVWUXFWLRQVZLOOQHJDWHWKHPDQXIDFWXUHU¶VZDUUDQW\
7KH$$PDQXIDFWXUHUDQGVXSSOLHUDFFHSWQROLDELOLW\IRUSHUVRQDOLQMXU\RU
property damage resulting from failure to follow the installation and operation
LQVWUXFWLRQVRUWKHXVHRIWKH$$LQDZD\WKDWPD\FDXVHDFFLGHQWVRU
damage or that may violate the law.
$OOWKHWHFKQLFDODQGFDEOHVSHFL¿FDWLRQVPXVWEHFKHFNHGDQGDGKHUHGWRDQG
ZLULQJGLDJUDPVPXVWEHIROORZHGZLWKRXWPRGL¿FDWLRQ
%HIRUHXVHWKH$$PXVWEHFRUUHFWO\VHWXSIRUDOOWKHHTXLSPHQWLWLVWRFRQWURO
DQGWHVWHGLQDVDIHHQYLURQPHQW7KH$$ZLOOQRWFRXQWFRUUHFWO\LIWKH
windlass selection is wrong or the windlass is not standard (eg it is installed
with a different chainwheel or motor).
$OOLQVWDOODWLRQVPXVWEHFDUULHGRXWLQDFFRUGDQFHZLWK86&*$%<&100$DQG
%0($UHTXLUHPHQWV
:KHQWKLVSURGXFWUHDFKHVWKHHQGRILWVXVHIXOOLIHLWPXVWEHGLVSRVHGRILQ
accordance with local regulations.
PART 1 IMPORTANT INFORMATION
READ BEFORE INSTALLING OR USING THE AUTOANCHOR
3
TECHNICAL SPECIFICATIONS
Parameter AA710 Remote Console AA702 Base Station
3RZHU6XSSO\ [$$9%DWWHULHV 99'&
0D[LPXP9ROWDJH 30V DC
Current Consumption 1$ P$
2XWSXW0D[LPXP
&XUUHQW'UDZ
1$ 9'&$
9'&$
The system has internal current
limiting and thermal shutdown.
2XWSXW0LQLPXP
&XUUHQW'UDZ
1$ 9'&P$
9'&P$
IP Rating ,3 ,3
2SHUDWLQJ7HPSHUDWXUH
Range o)WRo)o&WRoC) o)WRo)o&WRoC)
:LUHOHVV7UDQVPLVVLRQ *+],60%DQG,(((&RPSOLDQW%LW8QLTXH,'
:LUHOHVV5DQJH 7\SLFDO0LQLPXPPIW5DQJHGHSHQGVRQLQVWDOODWLRQ
2XWSXWV 6
6\VWHP6XSSRUWV 8SWREDVHVWDWLRQVDQGFRQVROHV
5RGH&KDLQ2QO\ 6WDLQOHVVRUJDOYDQLVHGVWHHO
Rode - Rope and Chain 0XVWKDYHDPLQLPXPRIIWPRIFKDLQ&KDLQPXVWEH
JDOYDQLVHGVWHHO5RSHVKRXOGEHDJRRGTXDOLW\Q\ORQDQFKRU
URSH7\SHRUHTXLYDOHQW
'&ZLQGODVVHVUHTXLUHDGXDOGLUHFWLRQVROHQRLG
4
RADIO FREQUENCY COMPLIANCE
FCC Information:
7KLVGHYLFHFRPSOLHVZLWK3DUWRIWKH)&&5XOHV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJ
WZRFRQGLWLRQVWKLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFHDQGWKLVGHYLFHPXVW
accept any interference received, including interference that may cause undesired
operation.
0RGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHPDQXIDFWXUHUFRXOGYRLGWKHXVHU¶VDXWKRULW\WR
RSHUDWHWKLVHTXLSPHQW
This device generates, uVHVDQGFDQUDGLDWHUDGLRIUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHG
DQGXVHGLQDFFRUGDQFHZLWKWKHPDQXIDFWXUHU¶VLQVWUXFWLRQVPD\FDXVHKDUPIXO
interference to radio communications.
ESTI Information (CE):
7KLVGHYLFHLVFRPSOLDQWZLWKWKHHVVHQWLDOUHTXLUHPHQWVRIWKH577('LUHFWLYH(&
PHHWLQJWKH(XURSHDQKDUPRQL]HG(0&DQGORZYROWDJHVDIHW\VWDQGDUGV
ELECTROMAGNETIC COMPATIBILITY (EMC)
FCC Information:
7KLVGHYLFHFRPSOLHVZLWK&)53DUWRI)&&5XOHVIRU&ODVV%HTXLSPHQW
ESTI Information (CE):
7KLVGHYLFHPHHWVWKHUHOHYDQWVWDQGDUGVVHWRXWLQ(XURSHDQ6WDQGDUG(1IRU
PDULWLPHQDYLJDWLRQDQGUDGLRFRPPXQLFDWLRQHTXLSPHQWDQGV\VWHPVThese standards
are intended to provide reasonable protection against interference by other emission
generating products on the boat. Compliance with these standards is no guarantee that
interference will not occur in a particular installation. The installation instructions must be
followed to minimise the potential for interference.
Note: If shielded cable is not used for the sensor connections this will compromise the
(0&DQGPD\LQYDOLGDWHWKHZDUUDQW\
$$HTXLSPHQW$$EDVHVWDWLRQDQG$$UHPRWHFRQVROHPXVWEHLQVWDOOHGDW
OHDVWIWPDZD\IURPDQ\HTXLSPHQWWUDQVPLWWLQJRUFDEOHVFDUU\LQJUDGLRVLJQDOVHJ
9+)UDGLRVPRGL¿HGVLQHZDYHLQYHUWHUVFDEOHVDQGDQWHQQDVRUUDGDUDQWHQQDVDQGDW
OHDVWIWPDZD\IURPDQ\66%HTXLSPHQW$$FDEOHVPXVWEHLQVWDOOHGDWOHDVW
IWPPDZD\IURPVXFKLWHPV
5
PART 2 INSTALLATION
Drilling the Deck: %HIRUHGULOOLQJLQWRWKHGHFNHQVXUHWKHUHLVQRWKLQJEHORZWKHGHFN
WKDWFRXOGEHGDPDJHGDQGWKDWDQ\KROH\RXGULOOZLOOQRWZHDNHQWKHERDW¶VVWUXFWXUH'ULOO
DKROHPP´GLDPHWHUWKURXJKWKHGHFN(QVXUHWKLVKROHLVGLUHFWO\LQOLQHZLWK
the sensor hole in the deckplate.
2.1 INSTALLATION TO OPERATE A WINDLASS
2.1.3 SENSOR INSTALLATION OVERVIEW
Vertical Windlasses: 7KHVHQVRULV¿WWHGLQWKHGHFNSODWH6RPHGHFNSODWHVDUHSUHGULOOHG
IRUWKHVHQVRU2WKHUVKDYHDGLPSOHRUPDUNWRVKRZZKHUHWKHVHQVRUVKRXOGEH¿WWHG
,IWKHZLQGODVVLVQRWIDFWRU\GULOOHGGULOODKROHPP´GLDPHWHUWKURXJKWKH
ZLQGODVVGHFNSODWH6HHWKHLQVWUXFWLRQVIRU\RXUVSHFL¿FZLQGODVVW\SH
Hori]ontal Windlasses: Sometimes it is not possible to ¿t the sensor to a hori]ontal
windlass or it ma\need to be ¿tted b\the windlass manufacturer. Before starting
check with the AutoAnchor manufacturer or supplier that it is possible to ¿t the
sensor to \our windlass. You ma\need a special ¿tting.
2.1.2 MAGNET INSTALLATION OVERVIEW
Check before starting. <RXUFKDLQZKHHOPD\EHSUH¿WWHGZLWKDPDJQHWRUSUHGULOOHG
UHDG\IRU\RXWR¿WWKHPDJQHW
Magnet Polarity: 1RWUHOHYDQWZKHQXVLQJWKHJUH\$$VHQVRURUDUHHGVZLWFK
VHQVRU,IUHWUR¿WWLQJXVLQJWKHEODFN$$VHQVRUWKHVRXWKSROHPDUNHGVLGHRI
the magnet must face the sensor.
Magnet Seal:,QVHUWWKHPDJQHWLQWRWKHKROHDQGFRYHULWZLWKDPLQLPXPRIPPRIHSR[\
WRSURWHFWLWDJDLQVWFRUURVLRQ6HH)LJRQSDJH
Magnet Size and Position: 5HIHUWRWKHLQVWUXFWLRQVIRU\RXUVSHFL¿FZLQGODVVW\SH
2.1.1 MAGNET AND SENSOR INSTALLATION
PLEASE READ BEFORE COMMENCING INSTALLATION
Correct magnet and sensor installation is critical for successful AutoAnchor
operation.
The AutoAnchor can be installed on vertical windlasses, drum winches and most
horizontal windlasses. Installation differs depending on the windlass type and on the
rode (all-chain or rope and chain). Please follow the instructions for your windlass
and rode. If it is not possible to comply with these instructions please check with the
AutoAnchor manufacturer or your supplier for other options or if you are not sure how to
proceed.
6HHwww.autoanchor.co.nz for contact information.
6
3DUW0DOH)LHOG&RQQHFWRU
3DUW)HPDOH)LHOG&RQQHFWRU
,IWKHUHLVQRSOXJRQWKHVHQVRUFDEOHDWWDFKWKH$$¿HOG
connector to the wires and use the connecting cable as above.
2.1.4 PLUG AND PLAY SENSOR CABLE
7KH$XWR$QFKRUSOXJDQGSOD\VHQVRUFDEOHLVFRUHWLQQHGVKLHOGHGFDEOH,WPXVWEH
XVHGWRFRQQHFWWKHVHQVRUWRWKHFRQVROHXQLW(QVXUHWKHFRQQHFWRUVDUH¿UPO\VFUHZHG
together.
The warranty does not apply if the sensor cable plugs are removed.
7KHVHQVRUFDEOHLV¿WWHGZLWKDIHPDOHSOXJWRFRQQHFWGLUHFWWRWKHPDOHFRQQHFWRURQWKH
$$EDVHVWDWLRQ,IDORQJHUOHQJWKLVUHTXLUHGVHQVRUFRQQHFWLQJFDEOHZLWKDPDOH
SOXJDWHDFKHQGLVDYDLODEOHLQWKHIROORZLQJOHQJWKV
P IW 3DUW
PIW 3DUW
P IW 3DUW
P IW 3DUW
P IW 3DUW
P IW 3DUW
$PPDOHIHPDOHFDEOH3DUWSOXVDJHQGHUFKDQJHU3DUWZLOOEHUHTXLUHG
to connect the extension cable to the base station.
Field Connectors
Sensor Connection:7KHVHQVRULVSOXJJHGGLUHFWLQWRWKH$$EDVHVWDWLRQ'RQRW
leave the cable hanging loose, it must be tied in place with cable ties. Extension cable,
JHQGHUFKDQJHUVDQG¿HOGFRQQHFWRUVDUHDYDLODEOHLIUHTXLUHG
6HQVRU3OXJ
Fitting the Sensor: 'RQRWIRUFHWKHVHQVRULQWRWKHKROH+DPPHULQJWKHVHQVRUKHDG
can damage the internal electronics. Ensure the sensor head is positioned so that it will not
EHKLWE\WKHFKDLQZKHHOGXULQJZLQGODVVRSHUDWLRQDQGWKDWLWLVDWOHDVWPPIWDZD\
IURPWKHEDWWHU\DQGPRWRUFDEOHV6HFXUHWKHVHQVRUXVLQJDJRRGTXDOLW\QHXWUDOFXUH
VLOLFRQHRUDVWURQJDGKHVLYHHJ6LNDÀH[RU0
Connecting 2 cables together:
,I\RXQHHGWRH[WHQGWKHFDEOHOHQJWKFDEOHVFDQEHMRLQHG
WRJHWKHUXVLQJ3DUW*HQGHU&KDQJHU
Antenna Plug
7
Dual Installation with Other AA Products
8VHWKH7DGDSWRU3DUWDQGWKHP0DOH)HPDOHH[WHQVLRQFDEOH
3DUW
2.1.5 REED SWITCH SENSORS
6RPHZLQGODVVHVDUHVXSSOLHGSUH¿WWHGZLWKDUHHGVZLWFKVHQVRU5HHGVZLWFKVHQVRUV
PXVWKDYHDPP[PPPDJQHWDQGWKHJDSEHWZHHQWKHUHHGVZLWFKVHQVRU
DQGWKHPDJQHWPXVWEHDPLQLPXPRIPPDQGDPD[LPXPRIPP7KLVVHQVRUUHTXLUHV
D¿HOGFRQQHFWRU
The AutoAnchor will operate with a reed switch sensor for all-chain rode. If using
combination rope and chain rode the reed switch sensor provides a reasonably accurate
count of rode deployed but on retrieval the display may be incorrect because it cannot
allow for the stretch in the rope.
)RUDQDFFXUDWHURSHDQGFKDLQFRXQWWKHUHHGVZLWFKVHQVRUVKRXOGEHUHSODFHGZLWKWKH
$$JUH\VHQVRU
2.1.6 SENSOR TUNING
:KHQWKH$XWR$QFKRULVFRPSOHWHO\LQVWDOOHGWKHVHQVRUPXVWEHWXQHG6HHWKH
LQVWUXFWLRQVRQSDJH
8
Magnet Fit'ULOODKROHPP´GLDPHWHUDQGPP´GHHSWR¿WWKH
magnet in the underside of a spoke in the bottom of the chainwheel. Cover the magnet
ZLWKDPLQLPXPRIPPHSR[\7KHPDJQHWVKRXOGEHDOLJQHGZLWKWKHVHQVRU6HH)LJ
2.1.7 INSTALLATION ON A VERTICAL WINDLASS - CHAIN ONLY
Magnet Size:6WDQGDUGVL]HLVPP[PPP7KLVPD\EHUHSODFHGZLWKWKH
VPDOOHUPP[PPPDJQHWLIUHTXLUHGIRU\RXUZLQGODVV
Gap Between the Sensor and Magnet:
6HQVRU 0DJQHW6L]H Gap
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
$$%ODFN6HQVRU $OO0DJQHWV 0LQLPXPPP0D[LPXPPP
5HHG6ZLWFK6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
Refer to the Overview Notes on page 5 before starting installation.
Sensor Connection:,GHDOO\WKHVHQVRUVKRXOGEHSOXJJHGGLUHFWO\LQWRWKH$$EDVH
VWDWLRQ,IORQJHUFDEOHLVUHTXLUHGXVHWKH$$PPDOHIHPDOHH[WHQVLRQFDEOH3DUW
RURQHRIWKH$$VWDQGDUGPDOHPDOHH[WHQVLRQFDEOHVSOXVWKHPFDEOHDQGD
JHQGHUFKDQJHU(QVXUHWKHFRQQHFWRUVDUH¿UPO\VFUHZHGWRJHWKHU6HHWKHLQIRUPDWLRQ
on page 6.
Loose cable should be tied in place with cable ties and kept clear of chain.
Sensor Position:7KH$$EODFNVHQVRUDQGWKHUHHGVZLWFKVHQVRUPXVWEH¿WWHGGLUHFOW\
LQOLQHZLWKWKHPDJQHWLQWKHFKDLQZKHHO6HH)LJDERYH7KH$$JUH\VHQVRUPD\EH
¿WWHGXSWRPPRXWRIDOLJQPHQW7KHJDSEHWZHHQWKHVHQVRUDQGPDJQHWPXVWEHDV
per the table below.
Note: If it is not possible to
align the sensor and magnet
exactly the AAgrey sensor may
EH¿WWHGXSWRPPRXWRI
alignment. The AA black sensor
and the reed switch sensor must
be directly aligned.
)LJ$OOVHQVRUV
6HDOZLWKPLQLPXPPPHSR[\
0DJQHW
6HQVRU
Chainwheel
'HFNSODWH
9
Magnet Fit: 6RPHZLQGODVVHVDUHSUHGULOOHGDQGRWKHUVQHHGDVSHFLDO¿W3OHDVHFKHFN
ZLWK\RXUVXSSOLHU7KHXVXDO¿WLVDVIROORZV'ULOODKROHPP´GLDPHWHUDQG
PP´GHHSLQWRDVSRNHLQWKHWRSRIWKHFKDLQZKHHO&RYHUWKHPDJQHWZLWKD
PLQLPXPRIPPHSR[\7KHPDJQHWDQGVHQVRUPXVWEHDOLJQHGVRWKDWWKHDQFKRUURGH
SDVVHVEHWZHHQWKHP6HH)LJV
6HQVR
r
0DJQHW
)LJ )LJ
2.1.8 INSTALLATION ON A VERTICAL WINDLASS - ROPE & CHAIN
)RUDQDFFXUDWHURSHDQGFKDLQFRXQWWKH rode must run between the sensor and
PDJQHW,I\RXUZLQGODVVLVSUH¿WWHGZLWKDPDJQHWLQWKHERWWRPRIWKHFKDLQZKHHO\RX
QHHGWRUHPRYHLWDQG¿WDQHZPDJQHWLQWKHWRSRIWKHFKDLQZKHHO5HIHUWR)LJV
Magnet Size:PP;PPPDJQHW$QPP[PPPDJQHWPD\EH
used on smaller windlasses. Check with your supplier.
Sensor Position7KHVHQVRUPXVWEH¿WWHGLQWRWKHGHFNSODWHZLWKLQWKHVHQVRUSRVLWLRQ
UDQJHDWWKHVWHUQHQGRIWKHZLQGODVV6HH)LJ,WPXVWDOVREHDOLJQHGZLWKWKHPDJQHW
so that the rode passes between the sensor and the magnet. The centre of the magnet
DQGWKHFHQWUHRIWKHVHQVRUPD\EHXSWRPPRXWRIGLUHFWDOLJQPHQW6HH)LJ7KH
gap between the sensor and magnet must be as per the table below.
Chainwheel
'HFNSODWH
)LJ
6HQVRU0DJQHWPD\EHXSWR
PPRXWRIGLUHFWDOLJQPHQW
PP
6HQVRU
0DJQHW
6HQVRU
0DJQHW
Sensor Position Rope & Chain Vertical Windlasses
Gap Between the Sensor and Magnet
Sensor Magnet Size Gap
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
Refer to the Overview Notes on page 5 before starting installation.
Sensor Connection: If longer cable is
UHTXLUHGWKH$XWR$QFKRUSOXJDQGSOD\
sensor extension cable must be used
WRFRQQHFWWKHVHQVRUWRWKH$$
base station. Ensure the connectors
DUH¿UPO\VFUHZHGWRJHWKHU6HHWKH
information on page 6.
Loose cable should be tied in place
with cable ties and kept clear of
chain.
6HDOZLWKPLQLPXPPPHSR[\
0DJQHW
)LJ
6HQVRU3RVLWLRQ
Range
90oBow
Stern
Rode
Anchor
Locker
Chainwheel
10
2.1.9 INSTALLATION ON A HORIZONTAL WINDLASS - CHAIN ONLY
)LJ
0DJQHWLQULPRIFKDLQZKHHODQGVWDQGDUG
sensor in sensor holder screwed to the deck
Magnet & Sensor Fitting for Chain Only Horizontal Windlasses
Magnet Size:PP[PPPDJQHW
Magnet Fit: ,I\RXUZLQGODVVLVQRWSUHGULOOHGGULOODKROHPP´GLDPHWHUDQGPP
´GHHSLQWKHHGJHRIWKHFKDLQZKHHO&RYHUWKHPDJQHWZLWKDPLQLPXPRIPP
epoxy.
Gap Between the Sensor and Magnet:
6HQVRU 0DJQHW6L]H Gap
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
$$*UH\6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
$$%ODFN6HQVRU $OO0DJQHWV 0LQLPXPPP0D[LPXPPP
5HHG6ZLWFK6HQVRU PP[PP 0LQLPXPPP0D[LPXPPP
Sensor Connection:,IORQJHUFDEOHLVUHTXLUHGWKH$XWR$QFKRUSOXJDQGSOD\VHQVRU
H[WHQVLRQFDEOHPXVWEHXVHGWRFRQQHFWWKHVHQVRUWRWKH$$EDVHVWDWLRQ(QVXUH
WKHFRQQHFWRUVDUH¿UPO\VFUHZHGWRJHWKHU6HHWKHLQIRUPDWLRQRQSDJH
Loose cable should be tied in place with cable ties and kept clear of chain.
Refer to the Overview Notes on page 5 before starting installation. It is not
possible to set out a single installation method for horizontal windlasses.
The sensor may be ¿tted inside the windlass or you may need a sensor
holder (Part #9110). See Fig 6 below. Often the sensor and magnet can only
be ¿tted by the windlass manufacturer.
6HQVRU+ROGHU
6HQVRU
0DJQHW
Sensor Position:7KH$XWR$QFKRUVHQVRUPD\EH¿WWHGXVLQJDVHQVRUKROGHU¿[HGWRWKH
GHFNWRVLWXQGHUWKHFKDLQZKHHO6HH)LJ7KH$XWR$QFKRUVHQVRUKROGHULVQRW
included in the standard kit. Check with your supplier if you need this. TheAA black sensor
DQGWKHUHHGVZLWFKVHQVRUPXVWEH¿WWHGGLUHFWO\LQOLQHZLWKWKHPDJQHWLQWKHFKDLQZKHHO
7KH$$JUH\VHQVRUPD\EH¿WWHGXSWRPPRXWRIDOLJQPHQW7KHJDSEHWZHHQWKH
sensor and magnet must be as per the table below.
11
Before starting check with the AutoAnchor manufacturer, or supplier, that it is
possible to ¿t the sensor and magnet to your horizontal windlass.
)RUDQDFFXUDWHURSHFRXQWWKHURGHPXVWUXQEHWZHHQWKHVHQVRUDQGPDJQHW2QD
KRUL]RQWDOZLQGODVVWKHPDJQHWDQGVHQVRUPXVWEH¿WWHGE\WKHZLQGODVVPDQXIDFWXUHU
,ILWLVQRWSRVVLEOHWRKDYHWKHVHQVRUDQGPDJQHW¿WWHGWRDFKLHYHWKLV\RXFDQXVHWKH
chain only horizontal windlass installation above. This provides an accurate count of rode
deployed but during retrieval the display may be incorrect because it cannot allow for
the stretch in the rope.
2.1.10 INSTALLATION ON A HORIZONTAL WINDLASS - ROPE & CHAIN
2.1.11 INSTALLATION ON DRUM WINCHES
For Drum Winch Set Up and Operation Refer to Page 33.
Gap Between the Sensor and Magnet:
0LQLPXPPPDQGPD[LPXPPP
The magnet and sensor must be ¿tted so that the gap remains consistent as the
winch turns
Magnet Installation:
6L]HPP[PPPDJQHW
7KHPDJQHWFDQEHPRXQWHGRQWKHPDLQVKDIWRURQWKHVLGHRIWKHGUXP6HH)LJVDQG
,IPRXQWHGRQWKHVLGHRIWKHGUXPSRVLWLRQLWFORVHWRWKHLQVLGHWRUHGXFHWKH
SHULSKHUDOVSHHGRIWKHPDJQHW)L[WKHPDJQHWLQWRSRVLWLRQZLWKHSR[\HQVXULQJLWLV
completely sealed to prevent corrosion.
Sensor Installation
7KH*UH\ZLUH$$VHQVRULVUHFRPPHQGHGEXWDSUR[LPLW\VHQVRUPD\EHXVHG
Every installation is different so this manual can provide guidelines only. TheAA sensor
KROGHURUDFXVWRPLVHGVHQVRUKROGHUZLOOEHUHTXLUHGWRHQVXUHWKHVHQVRUUHPDLQV
in position and the gap is consistent between the sensor and magnet during operation.
Sensor Connection: The AutoAnchor plug and play sensor extension cable must be
XVHGWRFRQQHFWWKHVHQVRUWRWKH$$EDVHVWDWLRQ(QVXUHWKHFRQQHFWRUVDUH¿UPO\
VFUHZHGWRJHWKHU6HHWKHLQIRUPDWLRQRQSDJH
Loose cable should be tied in place with cable ties and kept clear of chain.
0DJQHW
on side of
drum
0DJQHW
on shaft
6HQVRU
6HQVRU
)LJ )LJ
0DJQHW
6HQVRU
Fig 7
2'
,'
12
2.2 INSTALLATION TO OPERATE A THRUSTER
Before connecting the AA710 to operate a thruster you must ensure that the
thruster has been installed and tested by a Tuali¿ed marine electrician and that
the installation has been completed according to the thruster manufacturer’s
instructions.
5HIHUWRWKHZLULQJGLDJUDPDQGQRWHVVXSSOLHGIRUWKH$$
An isolating switch must be installed for controls if the main breaker or isolator is not
readily accessible from the helm.
,IWKHWKUXVWHUFRQWUROFLUFXLWXVHVQHJDWLYHVZLWFKLQJFRQQHFWDUHOD\EHWZHHQWKH$$
output and the control wire to convert from positive to negative switching.
The stern and bow output locations stated in the wiring are the default locations. These
FDQEHFKDQJHGXVLQJWKH$$VHWXSPHQX
7KHWKUXVWHUPDQXIDFWXUHU¶VVDIHW\UHTXLUHPHQWVIRUWHVWLQJDQGRSHUDWLQJWKHWKUXVWHUPXVW
EHDGKHUHGWRDWDOOWLPHVZKHQXVLQJWKH$$7KHVHLQFOXGHEXWDUHQRWOLPLWHGWR
1HYHURSHUDWHDWKUXVWHUFORVHWRSHRSOHVZLPPLQJ
1HYHUUXQWKHWKUXVWHURXWRIWKHZDWHU1RWHYHQIRUDVKRUWSHULRG$Q\RSHUDWLRQRI
the thruster out of the water can seriously damage the motor.
5XQQLQJDWKUXVWHUZLWKRXWUHVLVWDQFHIURPWKHSURSHOOHUFDQDOVRFDXVHVHULRXVGDPDJH
to the motor.
If the thruster stops giving thrust while the motor is running, turn it off
immediately.
2.2.1 POWER ENABLE SETTING
This is used to activate a power pack. It will time out and switch off after the delay time
selected.
2.3 INSTALLATION TO OPERATE AUXILIARY EQUIPMENT
2XWSXWVIURPWKH$$FDQEHFRQQHFWHGWRFRQWURODX[LOLDU\HTXLSPHQWRQWKHYHVVHO
VXFKDVOLJKWVGHFNRUDQFKRUZDVKSXPSVHOHFWULFFOHDWVDQGGDYLWV8SWRDX[LOLDU\
RXWSXWVFDQEHVHWXSSHUV\VWHP7KHRXWSXWVFDQEHGLVWULEXWHGDFURVVXSWREDVH
stations.
Before connecting the AA710 to operate auxiliary equipment you must ensure
that the equipment has been installed and tested by a quali¿ed marine electrician
and that the installation has been completed strictly according to the equipment
manufacturer’s instructions. The equipment must only be used according to the
equipment manufacturer’s instructions.
Refer to the wiring diagrams and notes suppliedIRUWKH$$
An isolating switch must be installed for controls if the main breaker or isolator is not
readily accessible from the helm.
Relays:,IWKHDX[LOLDU\HTXLSPHQWLVRXWVLGHWKHVSHFL¿FDWLRQRIWKH$$RXWSXWHJ
FXUUHQWJUHDWHUWKDQ$UHOD\VZLOOQHHGWREHLQWHUIDFHGEHWZHHQWKH$$RXWSXW
DQGWKHDX[LOLDU\HTXLSPHQW7KLVDSSOLHVDOVRLIWKHDX[LOLDU\HTXLSPHQWLVUXQQLQJRIID
different power supply.
13
$$
Terminal Default Function
Assignment
$OWHUQDWLYH)XQFWLRQ$VVLJQPHQW
%$77 (-) Ground
%$77 (+) Positive
287 (+) 1 Windlass
Down
Power Enable when
dual thrusters selected
287 (+) 1 Windlass
Up
287 (+) 2 Thruster A (Bow)
Port
:LQGODVV
2SWLRQ$
287 (+) 2 Thruster A (Bow)
Starboard
:LQGODVV
2SWLRQ%
287
:KLWH
(+) 2 Thruster B (Stern)
Port
Power Enable 5RSH&KDLQ
0RWRU/RDG:LUHV
287
%URZQ
(+) 2 Thruster B (Stern)
Starboard
'XDO6SHHG 5RSH&KDLQ
0RWRU/RDG:LUHV
2.4.1 BASE STATION INTERNAL CONNECTIONS
Notes:
8QXVHGRXWSXWVDUHDXWRPDWLFDOO\DVVLJQHGDVDX[LOLDU\RXWSXWV6HH3DJHVDQG
for more details. All outputs are active high (+).
2QO\RQHZLQGODVVFDQEHFRQQHFWHGWRDEDVHVWDWLRQZLQGODVVHVUHTXLUHEDVH
VWDWLRQV7KHZLQGODVVRXWSXWV287DQG287DUH¿[HGKRZHYHUWKH
control buttons for up and down can be swapped in the set up menu as can the
location of the windlass (bow or stern).
6WHUQDQGERZWKUXVWHURXWSXWORFDWLRQVVWDWHGDUHWKHGHIDXOWORFDWLRQV7KHVHFDQ
be swapped in the set up menu. The port and starboard directions for each output
cannot be changed.
2QO\UHTXLUHGIRUURSHFKDLQFRXQWLQJ
287 :KLWH0RWRU/RDG:LUH
287 %URZQ0RWRU/RDG:LUH
7KH$$NLWKDVRQHPDVWHUEDVHVWDWLRQDQGRQHUHPRWHFRQVROH
(DFKEDVHVWDWLRQKDVRXWSXWV8SWRVODYHVWDWLRQVFDQEHDWWDFKHGWRWKHPDVWHU
station to provide extra outputs.
2.4 REMOTE CONSOLE AND BASE STATION INSTALLATION
14
2.4.2 REMOTE CONSOLE INSTALLATION
The remote console is supplied with a cradle and
DFRYHU2QHUHPRWHFRQVROHFDQRSHUDWHPXOWLSOH
base stations. The console has a loop to allow for
a wrist or belt lanyard.
7KHFUDGOHVKRXOGEHPRXQWHGRQDÀDWVXUIDFH
DWOHDVWIWPDZD\IURPDQ\HTXLSPHQW
transmitting or cables carrying radio signals
HJ9+)UDGLRVFDEOHVDQGDQWHQQDVRUUDGDU
DQWHQQDDQGDWOHDVWIWPDZD\IURPDQ\
66%HTXLSPHQW
7KHUHPRWHFRQVROHLVVHDOHGWR,3
8SWRUHPRWHFRQVROHVFDQEHFRQQHFWHGWRDV\VWHP
7ZRDONDOLQH$$9EDWWHULHVDUHUHTXLUHGWRRSHUDWHWKHFRQVROH7KHVHDUHSUH¿WWHGLQ
new products.
To maintain the IP67 waterproof seal through the
cable gland a tinned, marine grade multi core
cable must be used and the base station must be
mounted so that the cables extend below the unit
when ¿xed to the wall.
WKHOLGFDQEHUHPRYHGHDVLO\GXULQJRSHUDWLRQ
WKH/('LQGLFDWRUVFDQEHVHHQGXULQJRSHUDWLRQ
WKHEHVWUHFHSWLRQLVDYDLODEOHVHH)LJ
WKHFDEOHVH[WHQGEHORZWKHXQLWZKHQ¿[HGWRWKHZDOO
to avoid condensation entering through the cable gland.
Cradle /RRSIRU
/DQ\DUG Cover
/(',QGLFDWRUV
2.4.3 BASE STATION
Wireless Communication
%HVWUHFHSWLRQIRUWKHZLUHOHVVVLJQDOLVRQWKHWRSRUVLGHV
of the base station as per the diagram. Alloy, steel or
FDUERQ¿EUHZLOOUHVWULFWWKHZLUHOHVVFRPPXQLFDWLRQ$Q
DQWHQQDPD\QHHGWREH¿WWHGLIZLUHOHVVFRPPXQLFDWLRQLV
LPSHGHG$$$QWHQQD3DUW
8SWREDVHVWDWLRQVFDQEHFRQQHFWHGWRDV\VWHP
:KHQRSHUDWLQJDZLQGODVVWKHEDVHVWDWLRQVKRXOGEH
PRXQWHGFORVHWRWKHZLQGODVVLQDSRVLWLRQZKHUH
)LJ
B
e
s
t
r
e
c
e
p
t
i
o
n
t
o
p
o
r
s
i
d
e
s
15
9RU9'&SRZHUVXSSO\LVUHTXLUHGWRWKH$$EDVHVWDWLRQ
Check battery polarity before connecting power and ensure output terminals will not short.
Refer to the manufacturer’s speci¿cationsIRUIXVHEUHDNHULVRODWRUDQGPDLQSRZHU
FDEOHVSHFL¿FDWLRQVIRUWKHHTXLSPHQWEHLQJFRQWUROOHGE\WKH$$
(QVXUHDQ\IXVHEUHDNHURQWKHFRQWUROFLUFXLWKDVDUDWLQJDSSOLFDEOHWRWKHFXUUHQWORDGV
FRQQHFWHGWRWKHRXWSXWV$$2XWSXWPD[LPXPLV$PSV$QDGGLWLRQDOLVRODWLQJ
switch should be installed for controls if the main breaker or isolator is not readily acessible
from the helm.
0XOWLSOHEDWWHU\EDQNQHJDWLYHWHUPLQDOVPXVWEHSHUPDQHQWO\FRQQHFWHGWRJHWKHUWR
become the common negative return (ground).
2.5.1 WINDLASS INSTALLATIONS
3RZHUVXSSO\WRWKH$$EDVHVWDWLRQPXVWEHIURPWKHZLQGODVVFRQWUROFLUFXLWDORQJ
with all other windlass controls eg. toggle switch, remote switches, deck switches, other
AutoAnchor devices. Power supply must not be from the motor positive near the
windlass.
2.5.2 MULTIPLE BASE STATION INSTALLATIONS
The master base station must be powered up when using a slave base station application.
6HSDUDWHEDVHVWDWLRQVPD\EHSRZHUHGIURPVHSDUDWHVXSSOLHVKRZHYHUif 2 products
are connected to the same base station they must be powered by the same supply,
or relays must be used as a means of isolation. To maintain power to the windlass it is
recommended that the windlass be attached to the master base station.
THE POWER SUPPLY MUST BE DISCONNECTED WHEN INSTALLING,
CONNECTING OR CHANGING THE WIRING
2.5 POWER SUPPLY
2.6 VOLTAGE LEVELS
1HLWKHUWKHZLQGODVVQRUWKH$XWR$QFKRUZLOORSHUDWHZLWKLQVXI¿FLHQWSRZHU6HHPLQLPXP
YROWDJHVEHORZ%DWWHULHVPXVWEHSURSHUO\PDLQWDLQHGDQGFKDUJHGDQGDOOFRQQHFWLRQV
DQGZLUHVPXVWEHRIJRRGTXDOLW\DQGWKHFRUUHFWJDXJHWRSUHYHQWYROWDJHGURS
Minimum Voltage Required 12V DC System 24V DC System
0LQLPXPYROWDJHUHTXLUHGWRVWDUWZLQGODVV 9'& 9'&
If the windlass is already operating, this is the
PLQLPXPYROWDJHUHTXLUHGWRFRQWLQXHRSHUDWLQJ.9'& 9'&
16
CABLE SPECIFICATIONS
An appropriate multi-core cable must be used to maintain the cable gland
seal into the base station.
Total Length Cable Size
Cable from AA702 Base Station to the Power Supply
/HVVWKDQPIW PP$:*
PIWPIW PP$:*
PIWPIW PP$:*
Cable from AA702 Base Station to Outputs
/HVVWKDQPIW PP$:*
PIWDQGPIW PP$:*
PIWDQGPIW PP$:*
Cable from Motor Load Wires
8SWRPIW PP$:*
2.7 WIRING
2.7.1 MOTOR LOAD WIRES (BROWN AND WHITE) OUTPUTS 5 & 6
Rope & Chain Counting: The brown and white wires must be connected direct to the
ZLQGODVVPRWRUWHUPLQDOVIRUURSHFKDLQFRXQWLQJA 1000 Ohm resister must be ¿tted
near the motor terminal for short circuit protection. The motor load terminators supplied
LQWKHNLWKDYHPRWRUWHUPLQDOFRQQHFWRUVZLWKD2KPUHVLVWRUSUH¿WWHG
,IWKH$$LV¿WWHGWRDQall-chain windlass, DWKUXVWHURUDX[LOLDU\HTXLSPHQW2XWSXWV
DQGFDQEHXVHGIRURWKHURSWLRQV
,QWHUORFNSURWHFWLRQLVLQFOXGHGLQWKHV\VWHP'RQRW¿WGLRGHVRULQWHUORFNGHYLFHVWR
outputs as these will prevent the system from operating correctly.
All battery and motor cables must be ring type, insulated to prevent short circuits and
LQVWDOOHGQRFORVHUWKDQIWPPDZD\IURPWKHVHQVRUKHDG
7RUHGXFHWKHSRWHQWLDOIRULQWHUIHUHQFHDOOFDEOHVPXVWEHORFDWHGDWOHDVWIWPP
DZD\IURPDQ\HTXLSPHQWWUDQVPLWWLQJRUFDEOHVFDUU\LQJUDGLRVLJQDOVHJ9+)RU66%
radios, cables and antennas or radar antennas.
'RQRWOHDYHFDEOHVKDQJLQJORRVHWKH\PXVWEHWLHGLQSODFHZLWKFDEOHWLHV
2.7.2 MULTIPLE AUTOANCHOR INSTALLATIONS
It is important when wiring multiple AutoAnchor products that potential differences do not
RFFXUDORQJWKHJURXQGFRQQHFWLRQ7KLVFDQFDXVHLQFRUUHFWFRXQWLQJ(QVXUH$$
DQG$$FRQVROHVDQG$$EDVHVWDWLRQVDUHVWDUJURXQGHGDQGWKDWWKHUHDUHQR
other high current paths between consoles. All wiring for multiple installations is run in
parallel. Refer to wiring diagrams for further details.
1
2.7.2 MULTIPLE AUTOANCHOR INSTALLATIONS
It is important when wiring multiple AutoAnchor products that potential differences do not
RFFXUDORQJWKHJURXQGFRQQHFWLRQ7KLVFDQFDXVHLQFRUUHFWFRXQWLQJ(QVXUH$$
DQG$$FRQVROHVDQG$$EDVHVWDWLRQVDUHVWDUJURXQGHGDQGWKDWWKHUHDUHQR
other high current paths between consoles. All wiring for multiple installations is run in
parallel. Refer to wiring diagrams for further details.
2.7.4 PLUG & PLAY SENSOR CONNECTIONS
7KH$$%DVH6WDWLRQDQGWKHVHQVRUDUHSUH¿WWHGZith connector plugs. The 2m sensor
FDEOHSOXJVGLUHFWLQWRWKHEDVHVWDWLRQ([WHQVLRQFDEOHVDUHDYDLODEOH6HHSDJHIRU
plug and play sensor cable information.
2.7.5 CONNECTING THE CABLES INTO THE BASE STATION
5HPRYHWKHOLGIURPWKH$$EDVHVWDWLRQ)HHGWKHPXOWLFRUHFDEOHWKURXJKWKH
waterproof gland. Connect the cables to the terminal block, using a screwdriver to press
GRZQDQGRSHQHDFKWHUPLQDODVUHTXLUHG6HHWKHSKRWRJUDSKEHORZTighten the cable
gland. Replace the lid.
2.7.3 CONNECTION TO LOW CURRENT DRIVES
:KHQFRQQHFWLQJWRHTXLSPHQWZLWKVROLGVWDWHVZLWFKLQJRr other low current drives, eg
3/&RU$&YDULDEOHIUHTXHQF\DGXPP\UHVLVWRUORDG3DUWPD\EHUHTXLUHGWR
SURYLGHVXI¿FLHQWORDGLQJDQGWRPHHW(0&DQGVDIHW\FRQVLGHUDWLRQV7KHUHVLVWRUSDFN
VKRXOGEHLQVWDOOHGFORVHWRWKHHTXLSPHQWFRQWUROnot on the AA703 base station.
2.7.6 WIRING DIAGRAMS FOR AA703 BASE STATION
:LULQJGLDJUDPVDUHLQFOXGHGLQWKHNLW3OHDVHUHIHUWRWKHPIRUZLULQJGHWDLO
These diagrams and installation help are also available on www.autoanchor.co.nz
Up
Up
Down
Down
BATT (-)
-
1
2
3
1000R
1000R
1
2
3
Low current
windlass drive
Part No
9515
AutoAnchor
18
3.1 USING THE AUTOANCHOR BUTTONS
2Q
6FUROO0HQX1XPEHUV8S'RZQ
0RGH6HOHFW(QWHU6DYH
(VFDSHRU%DFN
+ROGWRJHWKHUWRDFFHVVWKH6HWXSPHQX
+ROGIRUVHFRQGVWRGLVDEOHWKHORFN
+ROGIRUVHFRQGWRWRJJOHEHWZHHQPRGHVHJZLQGODVVWRWKUXVWHU
Control the windlass.
&RQWURO2SWLRQV$%7KUXVWHUDQG$X[LOLDU\RXWSXWV
Hold for 6 seconds to turn off.
6HWXSLQFOXGHVUHJLVWHULQJWKHZLUHOHVVLQWHUIDFHDQGFDOLEUDWLQJWKH$$V\VWHPIRUWKH
HTXLSPHQWLWLVWRFRQWURORQWKHERDW7KH$$PXVWEHWHVWHGZLWKDOOWKHHTXLSPHQWLW
is to control to ensure it is working correctly.
3.2.1 SYSTEM OVERVIEW
7KH$$NLWLVVXSSOLHGZLWK[$$UHPRWHFRQVROHDQG[$$PDVWHUEDVH
VWDWLRQ(DFKFRQVROHDQGEDVHVWDWLRQKDVDXQLTXH,'DQGWKHXQLWVPXVWEHUHJLVWHUHG
WRHDFKRWKHUWRRSHUDWHWKHV\VWHP,IH[WUDRXWSXWVDUHUHTXLUHGXSWR additional base
VWDWLRQVNQRZQDVVODYHVWDWLRQVPD\EHDGGHGLQWRWKHV\VWHP8SWRFRQVROHVFDQEH
UHJLVWHUHGWRRSHUDWHDV\VWHP)ROORZWKHLQVWUXFWLRQVWRUHJLVWHUWKHFRQVROHVDQGEDVH
stations.
3.2 WIRELESS INTERFACE SET UP
3.2.2 REGISTRATION SWITCH
/RFDWHGLQVLGHWKHEDVHVWDWLRQ8VHWRUHJLVWHUWKH
base station to the console and to register a slave
WRWKHPDVWHUEDVHVWDWLRQ6HHWKHLQVWUXFWLRQVRYHU
3.2.3 LED INDICATORS
System (Red)
6WHDG\UHGLQGLFDWHVSRZHULVRQ)ODVKLQJFRQWLQXRXVO\LQGLFDWHVUHJLVWUDWLRQ
VWDWHLVDFWLYH7LPHVRXWDIWHUPLQXWHV)ODVKLQJDVORZSXOVHLQGLFDWHVVHQVRU
is connected when the windlass is turning.
PART 3 SET UP
Network (Green)
6WHDG\JUHHQLQGLFDWHVWKHEDVHVWDWLRQLVDPDVWHUVWDWLRQ2IILQGLFDWHVWKHEDVH
VWDWLRQLVDVODYH6HHLQVWUXFWLRQVWRFRQQHFWDVODYHVWDWLRQEHORZ
Comms (Yellow)
)ODVKLQJLQGLFDWHVGDWDLVUHFHLYHG
Registration
6ZLWFK
19
3.2.5 REGISTER REMOTE CONSOLES TO THE BASE STATIONS
Each console must be registered separately.
7XUQRIIDOOFRQVROHV
7XUQRQWKHSRZHUWRDOOEDVHVWDWLRQV
8QVFUHZDQGUHPRYHWKHFRYHUIURPWKHmaster base station.
3UHVVWKH 0RGHEXWWRQWRWXUQRQWKHUHPRWHFRQVROH
The screen will tell you to “Press the register switch on the
PDVWHUEDVHVWDWLRQ´
3UHVVDQGUHOHDVHWKHUHJLVWUDWLRQEXWWRQ7KHJUHHQ/('
ZLOOVWD\RQ7KHUHG/('ZLOOÀDVKWRLQGLFDWHWKHFRQQHFWLRQ
is registering.
6. Registration is automatic. The screen will show that
the system is getting the network information and then
that the console has been successfully registered to the
EDVHVWDWLRQ7KLVFRXOGWDNHXSWRVHFRQGV
3UHVVWKH0RGHEXWWRQWRVHOHFW2.7KHFRQVROH
will return to the set up screen ready to set up the
system functions.
,I\RXKDYHPRUHWKDQFRQVROHWRUHJLVWHUWRWKH
base station repeat the steps above ensuring the
¿UVWFRQVROHLVWXUQHGRIIEHIRUH\RXVWDUW
:KHQ¿QLVKHGUHSODFHWKHOLGRQWKHEDVHVWDWLRQ
3.2.6 TO TURN THE AA710 REMOTE CONSOLE OFF AFTER REGISTRATION
3UHVVWKHOHIWDUURZWRHVFDSHIURP6HWXSWR
the default start up screen.
3UHVVWKH0RGHEXWWRQWRGLVSOD\WKHPHQX
6FUROOWR2II
6HOHFW2II
Note:7KH$$UHPRWHFRQVROHDXWRPDWLFDOO\WXUQVRIIDIWHUPLQXWHVZLWKRXWXVH The
$XWR2II7LPHFDQEHFKDQJHGIURPEHWZHHQWRPLQXWHVLQWKH6HWXSPHQX6HH
SDJH If you have more than 1 console you must set the time for each console.
3.2.4 TURN THE AA710 SYSTEM ON FOR THE FIRST TIME
(QVXUHWKH$$EDVHVWDWLRQLVSRZHUHGXS
3UHVVWKH0RGHEXWWRQRQWKH$$UHPRWH
FRQVROHWRWXUQLWRQ%HFDXVHWKHV\VWHP
is not yet set up, the screen will tell you to press
the registration switch on the master base station.
6HHLQVWUXFWLRQVEHORZWRUHJLVWHUWKHFRQVROHWR
to the base station.
This manual suits for next models
1
Table of contents
