HEATSTRIP HUSA01 User manual

CONTROLS
for HEATSTRIP HEATERS
PRODUCT MANUAL

2
HEATSTRIP CONTROLS REV D JUL15
To improve control of Heatstrip outdoor heaters there are a range of solutions to help you increase the use of
your outdoor entertaining area. The controllers include the following functions:
• Convenient easy to use hand held remote control
• Wall Switch can be wall mounted held remotely or junction box mounted to match your decor
• Multiple switches can control one heater
• One switch can control multiple heaters
• Wireless battery-less wall switch uses patented kinetic energy technology
• Auto Timer OFF function included in Relay
• Range of 80 feet for Remote Control and Switches
• Suitable for all heaters 120v 208v and 240v
• Purchase additional components as required
When specifying the controllers ensure there is one Relay for every heater.
All products are FCC approved for North America.
Easy to install and link the Remote Controls Switches and Relays. All components need to be protected from
the elements.
PART No: HUSA03
SINGLE WALL SWITCH
For controlling one heater or one zone of
heater. Remote control can control multiple
switches. No wiring required.Can be
mounted 3 ways flush in gang box on a
wall like a normal switch or loose as a hand
held remote control.
Range up to 80 feet (unobstructed)
INCLUDES:
1x SINGLE REMOTE CONTROL
2 x SWITCH
PART No: HUSA04
DOUBLE WALL SWITCH
For controlling two heaters independently.
Can also be used to control two zones of
heaters. Remote control can control multi-
ple switches. No wiring required.
Can be mounted 3 ways flush in gang box
on a wall like a normal switch or loose as a
hand held remote control.
Range up to 80 feet (unobstructed)
INCLUDES:
1x DOUBLE REMOTE CONTROL
PART No: HUSA06
REMOTE CONTROL
Hand held remote control
Can control two heaters
INCLUDES:
1 x REMOTE CONTROL
PART No: HUSA01
SINGLE SWITCH KIT
Remote Control and Switch in a kit to suit
one heater
INCLUDES:
1 x REMOTE CONTROL
1 x RELAY
1 x SINGLE WALL SWITCH
PART No: HUSA05
RELAY
One switch per heater
Must be accessible through gangbox
Can be programmed for Auto Off after
30 minutes or 1 hour
INCLUDES:
1 x SWITCH
PART No: HUSA02
DOUBLE SWITCH KIT
To suit two heaters controlled separately
INCLUDES:
1x REMOTE CONTROL
2 x RELAY
1 x DOUBLE WALL SWITCH

HUSA03
SINGLE ROCKER SWITCH
SPECIFICATIONS
Can control one heater or one set of heaters
Wireless wall switch
Detachable face plate
Fits inside standard junction box
HUSA04
DOUBLE ROCKER SWITCH
SPECIFICATIONS
Can control two heaters or two sets of heaters
Wireless wall switch
Detachable face plate
Fits inside standard junction box

HUSA05
RELAY
SPECIFICATIONS
Frequency 902MHz
Transmission Range 80ft(25m)
Dimensions 2.78” x 1.65” x 1.1”
(73 x 42 x 28mm)
Weight 3.02 Oz (90g)
Compliance ETL
FCC: SZV-STM300U
IC: 5713A-STM300U
Surge Protection 3000 volts
Line voltage 120 208. 240 volts
Current 16 amps
The relay receives wireless messages
from a switch to turn the Heater on
or off. The relay can control one
heater only.
FEATURES
ON/OFF control of the heater
Timer OFF function 15 30 45 60
minutes.
Can be controlled by multiple
switches and remote controls.
Adjustable antenna
SAFETY
Must be installed by a licensed in-
staller. Ensure all installation work
complies to local building codes.

HEATSTRIP
RELAY
240 Volt connection
EARTH
HOT LEG 2
HOT LEG 1
GANG BOX
HEATSTRIP
RELAY
120 Volt connection
EARTH
NEUTRAL
HOT LEG 1
GANG BOX
INSTALLATION
Can be mounted inside a standard junction box Attached using a standard knockout and thread connector with
nut (included).
The Relay is to be mounted indoors only and protected from the environment.
Use a non-metal electrical enclosure for best RF transmission.
Install in a suitable location taking care with interference through walls and other obstacles.
When the relay is first installed the relay will go through a start up sequence. this will take a few seconds then
it will be ready for programming.
NOTE: Wrap black electrical tape around the white
wire exiting the relay to indicate it as HOT!

NORMAL Operation Heater is on relay is closed
NORMAL Operation Heater is off relay is open
solid
solid
LIGHT TABLE
Menu Set
Menu Set
To exit any menu hold both buttons 2 seconds
Basic set up
Auto Off set up
To restore factory settings hold both buttons until
Menu is solid red and Set is solid Amber (approx 15
seconds)
solid
solid
Press and hold for Set for 3 seconds
Solid
Start you can now follow the sequence to which ever program
you want
RESTORE FACTORY SETTINGS
Option is pending
blink
Advanced set up
Active setting
blink

2. To enter Setup menu press both buttons for 2 sec-
onds
Menu Set
4. Press the ON button 3 times in quick succession.
Only one switch/remote control can be linked at a time.
Solid for 3
seconds
11
1
11
5. The relay will toggle on and off. Set light will be
solid for 3 seconds then change to 1 amber blink. This
has confirmed the link with the switch
7. To exit hold both buttons 2 seconds
solid
8. System will be back to NORMAL operation and
ready to operate
3. Ready to accept new links the link will stay open for
2 minutes. The Menu light will continue to blink once
as long as the relay is in the Setup menu.
6. Ready to accept new links. Single blink by both
lights. Repeat step 4 for more than 1 switch or remote
control.
1. NORMAL operation relay needs to be in this posi-
tion.
solid
LINKING RELAY TO SWITCHES & REMOTE CONTROL

UNLINK SWITCH
Menu Set
4. Press the Set button 3 times
2. To enter Setup menu press both buttons for 2 sec-
onds
Menu Set
11
3. Ready to accept new links the link will stay open for
2 minutes.
1. NORMAL operation relay needs to be in this posi-
tion.
solid
5. Press the ON button 3 times in quick succession.
Only one switch/remote control can be unlinked at a
time.
Solid for 3
seconds
1
6. The relay will toggle on and off. Set light will be
solid for 3 seconds.
8. To exit hold both buttons 2 seconds
solid
10. System will be back to NORMAL operation and
ready to operate
3 Blink
3 Blink
7. The Set light will change to 3 amber blinks. The
relay is ready to unlink the next device.
1
9. Both lights will flash twice to signal exit of program
22
1

SET UP AUTO OFF FUNCTION
The relay comes with an option to program in an Auto-Off function.
The factory default auto off is disabled to begin with.
The Auto-Off is active all the time once programmed. To change it you’ll need access to the relay and to go
through this program again.
2. To enter Setup menu press both buttons for 2 sec-
onds
Menu Set
1. Start Relay needs to be in either of the two modes
solid
11
4. Press the Menu button four times quickly
3. Relay is ready to accept change of Menu
41
5. The Menu button will continue to flash 4 times as
long as you are in this function.
6. To select an option
press the set button the
number of times in the
table. The set button
will flash amber to the
corresponding time peri-
7. Confirm option by holding down Set button for 2 seconds
4Flash
9. To exit back to Start
solid
10. System will be OFF and ready to operate
4
8. The set button will flash the number of times corre-
sponding with the time chosen

HUSA04
REMOTE CONTROL
SPECIFICATIONS
Small handheld
Can control two heaters or two sets of heaters
RANGE: 80 feet
FREQUENCY: 902 MHz
CHANNELS: 4 buttons ( 2 orckers0
DIMENSIONS: 1.85 x 3.15 x .7 inches
ADDRESSING: Factory set unique ID
(1 of 4 billion)