Maxxair HVPF 20 OR User manual

MODEL #: HVPF 20 OR
1
20 IN. OUTDOOR PEDESTAL FAN
English
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-433-1626

PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
1ydoBnaFA 1Stand PoleB 1BaseC
2
A
C
B

3
AA CCBB
HARDWARE CONTENTS (shown actual size)
!SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product. If you have any questions regarding the product,
please call customer service at
1-800-433-1626
Qty. 2
Spring Washer
Qty. 2
Screw
WARNING
• When using electric products, basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and personal injury. Follow these important safety guidelines.
• Do not use this fan with any solid-state speed control device.
•Do not use an extension cord with this fan.
• Do not expose to rain. Store indoors.
• Do not use with damaged cord, plug or other parts.
• Keep cord away from heated surface.
• Do not handle plug or the fan with wet hands.
• Do not touch the terminals of plug when installing or removing the plug from the outlet.
• Unplug or disconnect the fan from power supply before servicing.
• After servicing, any safety device (includinggrilles, impeller, etc.) should be reinstalled or
remounted as previously installed.
• This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they are given
supervision or instruction concerning useof the product by a person responsible for their
safety. Children should be supervised to ensure that they do not play with this product.
PLEASE READ AND SAVE THESE INSTRUCTIONS.
Plastic Nut Tightener
Qty. 2
(preassembled)

4
WARNING
CAUTION
•THE POWER CORD is equipped with a three-prong, grounded GFCI (Ground Fault Circuit
Interrupter) plug that must be inserted into a grounded receptacle or GFCI power outlet.
Under no circumstances must the grounding prong be cut off the plug.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. lf any part is missing or damaged, do not attempt to
assemble or operate the product.
Estimated Assembly Times: 30 minutes
Tools Required for Assembly: Phillips Screwdriver (not included)
• CONSIDER YOUR WORK AREA ENVIRONMENT. Don’t operate fan in presence of flammable
liquids or gases like gasoline or other fuels, lighter fluid cleaners, oil-based paints, natural gas,
hydrogen, coal dust, magnesium dust, grain dust, or explosive dust like powder.
Do not use or store near hazardous or toxic materials.
• USE SAFETY GLASSES. Also use face or dust mask if work area is dusty.The operation of
any fan can result in foreign objects being blown into the eyes, which can result in severe eye
damage. Always wear safety goggles complying with ANSI Z87.1.
• DON’T ABUSE CORD. Never pull the power cord or yank it to disconnect from receptacle.
To unplug, grasp the plug, not the cord. Keep cord away from heat, oil, and sharp edges.
Do not pull or carry by cord, use cord as handle, close a door on cord, or pull around sharp
edges or corners.
• MAINTAIN fan. Keep fan clean at all times. Keep dry, clean and free from moisture.
• DISCONNECT fan when not in use. Don’t operate unit unattended.
• NEVER stick any object into the grille openings of the fan.
• RETURN for repair or to replace damaged parts if any are found to be broken or if the fan is
inoperative.
•IF the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.

ASSEMBLY INSTRUCTIONS
1. Attach stand pole (B) to the base
(C) and secure with 4 screws (BB)
and 4 spring washers (CC)
Make sure all screws are tightened
firmly.
HARDWARE USED
5
x 4
x 4
BB
CC
Screw
Spring Washer
B
BB
CC
C
1

1. Test GFCI (Ground Fault Circuit Interrupter)
plug BEFORE EACH USE.
• Plug GFCI into power outlet. Press RESET
button (A). Indicator (B) should turn red.
• Press TEST button (C). Indicator (B) should
turn off. GFCI plug is tripped.
• Press RESET button (A) again for use.
• DO NOT USE FAN IF ABOVE TEST FAILS.
Call customer service department for assistance.
ASSEMBLY INSTRUCTIONS
HARDWARE USED
Attach the fan body (A) to the stand pole (B).
To adjust air flow up and down,
tilt the fan to the desired angle.
Tighten the plastic nut tightener (AA)
on both tilt nuts to secure fan head.
Align holes on the pole of fan body (A) and
attach 2 screws (BB) and 2 spring washers (CC),
then tighten the screws (BB) firmly.
6
2x
x 2
x 2
AA
renethgiTtuNcitsalP
BB
CC
Screw
Spring Washer
2.
OPERATING INSTRUCTIONS
C
B
A
RESET
TEST
2
AA
CCBB
1

OPERATING INSTRUCTIONS
2. ADJUSTING AIR SPEED
The fan has three speeds (LOW,
MEDIUM and HIGH).
Pull the chain of the speed control switch on
the back of the unit to adjust air flow
to desired speed.
CARE AND MAINTENANCE
• Unplug from electrical source to clean.
• Use soft, damp cloth to clean. Following that, wipe with clean, dry cloth.
• Do not bend the fan blades.
• Store in a dry place.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Fan won’t run.1. Fan is not plugged in.
2. Unit is not turned on.
3. GFCI needs to be
reset.
1. Make sure unit is plugged in.
2. Check that unit is turned on.
3. Unplug fan and follow the
instructions on page 6 to
reset GFCI plug.
Oscillating feature not
working. 1. Oscillating feature is not turned on. 1. Make sure that oscillation switch is turned on.
7
Before returning to your retailer, call our customer service department at 1-800-433-1626
2

8
VENTAMATIC, LTD. LIMITED WARRANTY
This warranty is underwritten by Falco Insurance Company and is extended to the original retail
purchaser of this model or, if this unit is purchased and requires installation by a building
contractor, to the original owner of the home. No subsequent purchaser of the unit or of a home
in which it is installed is entitled to any of the benefits of this warranty.
This product is warranted against defects in materials and workmanship for a period of one (1)
year from the date of original retail purchase. No other parts or components are warranted.
There is no warranty for defects caused by abuse, faulty installation, or the like.
Repairs or replacement parts supplied under this warranty are warranted only for the period of
this warranty; that is, one (1) year from the date of the original retail purchase of the unit.
In the event of a defect or malfunction, we will replace or repair the defective part or component
only and return the new or repaired part to you freight prepaid.
You must bear all other expenses incurred in obtaining repairs, including labor required for field
repair or replacement, and the cost of shipping the defective part to us. You must also bear the
cost of repair to or replacement of any part or component and the shipping charges incurred for
the repair or replacement and return to you of any part or component not covered by this
warranty, including parts or components damaged by you.
The company reserves the right to demand and receive written evidence of the date of purchase
before undertaking its obligations under this warranty. The right to demand and receive written
evidence of date of purchase extends to all licensed dealers of Ventamatic, Ltd. products.
You should, therefore, retain your sales slip and attach a copy of it to the warranty claim.
To start a warranty claim you must:
Contact Ventamatic, Ltd.
An RGA (Returned Goods Authorization) form is required for returns to the factory to ensure
your return can be processed efficiently and quickly. Please contact Ventamatic, Ltd. toll-free at
800-433-1626 or via web at www.MYMAXXAIR.com to obtain an RGA and follow the
instructions given.
There is no informal dispute settling mechanism available in the event of a controversy involving
this warranty.
Any and all implied warranties which may exist terminate upon the expiration of this warranty
one (1) year from the date of the original retail purchase. Some states do not allow limitations on
how long an implied warranty lasts, so this limitation may not apply to you.
Ventamatic, Ltd. is not liable to you for incidental or consequential damages arising out of defect
or malfunction of a unit or its installation or out of any alleged breach of this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so this
limitation may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.
rev.4/19

9
REPLACEMENT PARTS LIST
TECHNICAL DATA
VOLTAGE/FREQUENCY CURRENT POWER CONSUMPTION
W120A1.1120 V/60 Hz
C
K
B
G
F
E
A
I
H
AA
D
J
PART DESCRIPTION PART #
A Fan Motor 20P-OD-01
E Speed Switch20P-OD-05
FPower Cord
D Fan Blade20P-OD-04
Plastic Tightener20P-OD-12
KCover Ring 20P-OD-11
BStand Pole 20P-OD-02
C Base20P-OD-03
H Drum 20P-OD-08
G U Arm 20P-OD-07
AA
Rear Grille
Front Grille
20P-OD-06
20P-OD-09
20P-OD-10