Maykke Winston User manual

PRODUCT INSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 1
PRE-INSTALLATION
Tools Required
Rubber mallet Safety goggles Phillips
screwdriver
Level Silicone
Compound
AA
Hardware Included
Part Description Quantity
AA Leg levelers (pre-installed on legs) 4
Description Quantity
Wood screws 2
1
5/16” Lag Bolts (min. 250lbs) load bearing 2
Washers for Lag Bolts 2
Materials Required
WHAT IS COVERED
All products in the package carry a One-Year Limited Lifetime warranty. This warranty applies only to the original
purchaser and to the original installation of the product.
WHAT IS NOT COVERED
Damage caused during moving or during installation is not a defect or warranty issue and will not be considered as such.
This warranty does not cover product failure caused by abusive treatment, surface scratches, misuse, neglect or damage
due to handling or faulty installations. All wood naturally ages, darkens, changes in color, and mellows over time due
to exposure to light. While this color change is imperceptible from day to day
time, or due to amount of light the wood is exposed to. Imperfections such as small surface splits, small dark holes or
darker mineral streaks are natural and are not considered defects.
LIMITED LIFETIME WARRANTY
MODEL: YSA1432101

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 2
Package Contents
A
Part Description Quantity
A Cabinet body 1
INSTALLATION
1Tracing the outline of the vanity
Determine the ideal location for your new bath furniture.
If placing the side cabinet along the wall, then trace
its outline on the wall.
will attach the vanity.
With a level, draw lines along the studs from the
you spot where to place the screws in Step 3.
PRE-INSTALLATION (continued)

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 3
INSTALLATION (continued)
2Installing support for vanity
properly support the vanity.
To properly secure the vanity, the middle of the
required 2x6 backing material must be 31-7/8”
Extend the backing material beyond the width of the
vanity to the nearest stud. This will ensure proper
support for the vanity.
Front-notch the studs to ensure the 2x6 backing
Secure the 2x6 backing material to the studs with
framing nails.
Rough-in the water supply and drain lines into the
rough-in plumbing areas of the vanity.
3Attaching the vanity
Verify the vanity is level and back rail is plumb
against the wall. If necessary, turn the leg levelers
(AA) to adjust the vanity.
Using drill bit, drill two pilot holes through the back
positioned to ensure the lag bolts will engage the
2x6 backing material.
lag bolts and washers (not provided).
31-7/8” (810mm)
2”x6” backing material
AA
A

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 4
DOOR ADJUSTMENT
LEFT TO RIGHT
FRONT TO BACK
UP AND DOWN
door
door
door
vanity side panel
vanity side panel
vanity side panel
If the gap between the door and vanity side panel needs
adjustment, turn the screw closest to the door clockwise
or counter clockwise.
Make sure to adjust both the top and bottom hinges to
keep the door level.
If the door is not aligned perfectly with the vanity frame,
turn the screw closest to the vanity side panel clockwise
or counter clockwise.
Make sure to adjust both the top and bottom hinges to
keep the door level.
If the gap above or below the door needs adjustment,
turn the screw that is mounted to the hinge plate of the
vanity side panel.
Loosening the screw allows the door to move up or
down.
Both hinges of the door need to be loosened to adjust
the door.
Remember to tighten the hinges after the door is in
place.

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 5
If the gaps above or below the drawer need adjustment, simply
turn the screw that is mounted to the glide of the drawer box.
By loosening the screws this gives the drawer box freedom to
move up or down.
Remember to tighten the screws after the drawer box is in
place.
If the drawer is not aligned with the vanity frame, pull the drawer
out to its furthest point to reveal the screw closest to you.
By turning the screw clockwise or counter clockwise it will
adjust the depth of the drawer.
DRAWER ADJUSTMENT
UP AND DOWN
FRONT TO BACK

PRODUCT INSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 1
PRE-INSTALLATION
Tools Required
Rubber mallet Safety goggles Phillips
screwdriver
Level Silicone
Compound
AA
Hardware Included
Part Description Quantity
AA Wall cleat 1 set
BB Anchor and screws 2 sets
Description Quantity
3/4" length wood screws 4
Materials Required
MODEL: YSA1432101
BB

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 2
Package Contents
A
Part Description Quantity
A Cabinet body 1
INSTALLATION
1Installing wall cleats
Determine the ideal location for your new bath furniture.
Mark the wall cleat on the wall at the desired
location of the linen cabinet.
Drill 1/4" holes to prepare the wall for the anchors.
Push the anchors into the holes.
Place the wall cleat over the anchors and line up
the holes, then fasten the screws into the anchors.
PRE-INSTALLATION (continued)
The linen cabinet may be placed on the wall as a standalone cabinet,
or installed on top of the Woodbridge side cabinet.
If installing on the wall please follow steps 1 - 3.
If installing on the Wood bridge side cabinet follow step 4.

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 3
INSTALLATION (continued)
2Installing wall cleat to the cabinet
Locate the pre-drilled holes behind the cabinet.
Place the wall cleat over the back of the cabinet and
line up the holes, then fasten the screws.
3Hanging the cabinet
Lift and slowly drop the cabinet so the wall cleats
meet and sit in place.
The weight of the cabinet will keep the wall cleat
from moving.

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 4
INSTALLATION
4Placing linen cabinet over side cabinet
Place the linen cabinet over the side cabinet making
sure the corners line up.
Use 3/4" length wood screws from inside of the
linen cabinet to the top of the side cabinet.

PRODUCTINSTALLATION
WINSTON LINEN TOWER
REV 111715
PRODUCT INSTALLATION 6
CARE AND CLEANING
WOOD DOORS AND PANELS
Dust cabinets frequently with a soft, lint-free cloth. You may dampen the cloth with water or with a spray-type dust
remover. Clean up spills immediately. Use a clean, damp cloth if necessary. Wipe dry with another clean soft cloth. Cloth
is better than paper towels for this purpose.
For maintenance cleaning of your cabinet, there are a number of products available for your wood cleaning needs,
typically promoted as furniture care products. We suggest using mild soap with a damp cloth to remove any build up
on cabinets. Any product used should be applied and then quickly and completely removed with a damp cloth. Dry the
wet or damp cloths over the edge of doors.
Do not use detergents, soap pads, steel wool or any other type of abrasive pad on your cabinet. These products will
LAMINATES
You can clean all laminated surfaces by using a damp, soft cloth. Do not use excessive amounts of water, it will seep into
the seams of the cabinet. Sink base cabinets are the most common cabinet to have water damage and can usually be
protected with a plastic liner or pan.
PREVENTING HEAT OR HUMIDITY DAMAGE
The bathroom environment is very common place for humidity. It is very important to dissipate the humidity in the room
and not let it stay for long periods of time. If higher temperature settings are used for extended periods of time, the
heat may be excessive and the doors and drawer fronts should be removed. This is particularly important on laminated
damage.
SUNLIGHT AND AGING
Over time, exposure to sunlight, smoke and chemicals may cause some materials to face or vary from their original color.
samples on displays may not represent the exact color of cabinets received at the time of shipment.
VITREOUS CHINA
Vitreous china vanity tops and sinks are very durable. The glazing process provides years of enjoyment if cared for
correctly. Rinse thoroughly and use a soft cloth to wipe the product dry after each use to prevent hard water stains. Soft
abrasive cleaners may be used when necessary to clean vitreous china products.
GRANITE OR MARBLE TOPS
Natural stone is a porous material. Therefore, it may stain if not properly cared for. Granite counter tops should be sealed
before using. Follow the instructions on the sealer label. The easiest way to clean granite counter tops is to simply use
warm water and mild liquid dish soap, preferably without aromatics. This is a gentle way to clean the grease and grime
from your granite counters without damaging them. If you use plain soap and water, this can lead to soap build up and
and dry with a soft cotton cloth.
QUARTZ TOPS
Quartz is easy to maintain. It is a non-porous material that is highly resistant to stain, scratches and heat. However, it is
not stain, scratch, or heat proof. Spills should be cleaned as soon as possible with soap and water on a regular basis
to keep the polished quartz looking like new. Use warm water and a damp cloth with a small amount of non-abrasive
cleaner that does not contain bleach.