Maykke YSA1203601 User manual

REV. 12292015SPECIFICATION SHEET www.maykke.com
SPECIFICATION SHEET
Furniture grade construction consisting of a Solid wood Frame
U-shaped drawer for maximum storage
Full extension, soft close drawers with dovetail construction
Wall mount bracket included
Note:
Model: YSA1203601
YSA1203602
Top
SideFront
36" Dani Vanity White
36”
36”
6”
15”
3⁄”
12¼” 12⁄”
3⅛”
4¾”
15”

REV. 12292015SPECIFICATION SHEET www.maykke.com
SPECIFICATION SHEET
Includes matching backsplash
Natural Stone top works with most 37" wide, standard depth vanities
Pre drilled faucet holes for an 8" widespread faucet
Sinkcut out accomidates the YSA1092001 Bristol undermount ceramic sink
NOTE:
Model: YSA1123701
Top
Back splash
Side
11”
4” 4”

REV. 03112016SPECIFICATION SHEET www.maykke.com
SPECIFICATION SHEET
Ceramic Vessel with Overflow
Note:
Model: YSA1092001 and YSA1092002
Top
Side
By IAPMO, ceramic lavatory warpage is defective only if warpage of flat slab out of horizontal plane exceeds 6.3 mm/m
(0.25 in/ft) on all sizes
OR warpage on back of lavatories that are attached to the wall exceeds 3 mm (0.13 in).
Bristol
Front
Available Colors: White and Biscuit
5"
14-3/8"
18-1/4"
6-1/8"
7-1/4"
20-7/8"
3-3/4"
6-1/8"
7-1/4"
2-1/2"

www.maykke.com
Wall-Hung Vanity Set
Installation, Care Guide
and Warranty
YSA1203601 YSA1203602

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
AA
Hardware Included
Part Description Quantity
AA Mounting Brackets 2 sets
BB Anchor and screws 2 sets
BB
PRE-INSTALLATION
Tools Required
Rubber mallet Safety goggles Phillips
screwdriver
Level Silicone
Compound
NOTICE: Do not change or modify the product in any way. Doing so may compromise the
products structural integrity and will void the warranty.
NOTICE: Installation instructions must be followed. Any diversions from the installations
instructions may risk property damage and will void the warranty.
NOTICE: When moving your vanity be sure to lift, never slide or pull, doing so may
result in damage to the product.
IMPORTANT:
Observe all state and local building codes.
1
由Autodesk 教育版产品制作
由 Autodesk 教育版产品制作
由
Autodesk
教育版产品制作
由
Autodesk
教育版产品制作

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
Package Contents
A
Part Description Quantity
A Cabinet body 1
INSTALLATION
1Determine ideal position (see fig 1)
Determine the ideal location for your new bath furni-
ture.
□Use a stud finder to locate the studs to which
you will attach the vanity. Vanity heights
should be within 32" - 34" from the floor to
top of vanity (including vanity top).
□With a level, draw lines along the studs from
the floor to the top of the vanity. These lines
will help you spot where to place the screws
in Step 3.
□Using a 5/16" drill 2 holes into the wall and
secure the anchors into the wall.
PRE-INSTALLATION (continued)
2
Fig 1

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
INSTALLATION (continued)
3Mounting the wall vanity (see fig 3 & 4)
Before attaching the vanity to the wall make sure
the vanity is clear of any plumbing. Modifications
may be needed due to dierent plumbing. It
is recommended that you discuss this with a
professional before attempting to install the vanity.
□Attach the mounting brackets to the back of
the vanity by lining up the pre-drilled holes
and brackets.
□Secure the mounting brackets to the back of
the vanity.
□Position the wall vanity to the wall cleat on
the wall and let it rest into the cleat
4Leveling vanity
□Verify the vanity is level and back rail is flush
against the wall.
3
2Installing support for vanity (see fig 2)
Provide 2x6 backing material behind the nished wall to properly
support the vanity.
□Extend the backing material beyond the width of the
vanity to the nearest stud. This will ensure proper support
for the vanity.
□Front-notch the studs to ensure the 2x6 backing material
is ush against the studs.
□Secure the 2x6 backing material to the studs with framing
nails.
□Rough-in the water supply and drain lines into the rough-
in plumbing areas of the vanity.
2”x6” backing material
Fig 2
Fig 3
Fig 4
由Autodesk 教育版产品制作
由
Autodesk
教育版产品制作
由
Autodesk
教育版产品制作
由
Autodesk
教育版产品制作
由Autodesk 教育版产品制作
由 Autodesk 教育版产品制作
由
Autodesk
教育版产品制作
由
Autodesk
教育版产品制作

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
INSTALLATION (continued)
4Installing the faucet to the vanity top
Follow the manufacturer's instructions to install the faucet and
drain assembly to the vanity top.
6
□Place the vanity top (C) with the sink (D) over the
vanity (A).
□Make sure the wall is straight and there are no gaps
between the wall and vanity top (C).
□Remove the top (C) and apply a small bead of
silicone compound to the top of the vanity before
the vanity top is set into position.
□Firmly press the vanity top (C) into position; check
the level and evenness across the front of the vanity
(A), and make sure the vanity top (C) is flush to the
wall.
□Apply silicone compound to the back and bottom
of the backsplash (B). Firmly press the backsplash
(B) to the vanity top (C) to set into place, then
firmly press the backsplash (B) to the wall.
7Reconnecting the water supply
□Reconnect the faucet supply lines to the water
supply and reconnect the p-trap.
□Install the pop-up drain.
□Turn on the water supply or the home’s main
water supply and test for leaks.
D
A
C
B
5Installing the Sink to the top
(If installing Maykke sink)
□Turn the vanity top (C) upside down and unscrew
the bolts attaching the preinstalled sink (D) to the
top (C).
□Apply a small bead of silicone compound around
the sink cut out on the vanity top (C), reposition the
sink (D) on the top (C), pressing firmly together.
□Secure the sink (D) to the top (C) with the screws.
4
Securing the vanity top
(If installing Maykke vanity top) (see fig 5)
Fig 5

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
If the gaps above or below the drawer need
adjustment, simply turn the screw that is mounted
to the glide of the drawer box.
By loosening the screws this gives the drawer box
freedom to move up or down.
Remember to tighten the screws after the drawer
box is in place.
If the drawer is not aligned with the vanity frame,
pull the drawer out to its furthest point to reveal
the screw closest to you.
By turning the screw clockwise or counter
clockwise it will adjust the depth of the drawer.
Adjust the drawer until the face is flush with the
vanity frame.
DRAWER ADJUSTMENT
6
FRONT TO BACK
UP AND DOWN

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
CARE AND CLEANING
Wood
Care: Excess moisture can be damaging to any fine wood finish, be sure to clean up any spills right
away.
Over time, exposure to sunlight, smoke and chemicals may cause some finishes to vary from their
original color. Cabinets or accessories added at a later date may not match cabinets previously
installed. For the same reason, finish samples on displays may not represent the exact color of
cabinets received at the time of shipment.
Over exposure to humidity may cause permanent damage to the product. It is very important to
dissipate the humidity in the room as soon as possible. If exposed to higher temperatures (excess of
160˚) for extended periods of time the heat may be excessive and the doors and drawers should be
removed right away.
Cleaning: Dust Cabinets using a soft, lint-free cloth. When needed, clean the vanity with a
clean damp cloth, wiping dry with another clean soft cloth. A non-silicone based furniture cleaner
can be used periodically when additional cleaning is needed.
Vitreous China
Care: Rinse thoroughly and use a soft cloth to wipe the product dry after each use to prevent hard
water stains.
Cleaning: Soft abrasive cleaners may be used when necessary.
Granite or Marble Tops
Care: Natural stone is a porous material; and may stain if not properly cared for. Stone tops should
be sealed before using. Follow the instructions on the sealer label.
Cleaning: For best results use a natural stone cleaner and follow the directions on the label.
Quartz Tops
Care: Quartz is an easy material to maintain. It is a non-porous material that is highly resistant to
staining, scratching, and heat. Though non-porous, it is not stain, scratch, or heat proof. Spills should
be cleaned as soon as possible.
Cleaning: For best results use warm water with a small amount of non-abrasive cleaner that does
not contain bleach.
6

REV. 05092016INSTALLATION AND CARE GUIDE www.maykke.com
INSTALLATION AND CARE GUIDE
7
WHAT IS COVERED
All products in the package carry a One-Year Limited Warranty. This warranty applies only to the original
purchaser and to the original installation of the product.
WHAT IS NOT COVERED
Damage caused during moving or during installation is not a defect or warranty issue and will not be
considered as such. This warranty does not cover product failure caused by abusive treatment, surface
scratches, misuse, neglect or damage due to handling or faulty installations. All wood naturally ages,
darkens, changes in color, and mellows over time due to exposure to light. While this color change is
imperceptible from day to day, it may be significant over a long period of time, or due to amount of light
the wood is exposed to. Imperfections such as small surface splits, small dark holes or darker mineral
streaks are natural and are not considered defects.
Contact [e-mail] or call toll free 1 [phone] M-F 7:30am - 4:30pm (PST) with any
questions or warranty concerns
WARRANTY