Maytag MDE22PNAGW0 User manual

COMMERCIAL HE DRYER iNSTALLATiON iNSTRUCTiONS
Electric
iNSTRUCTiONSD'INSTALLATIOND'UN SECHE-LINGEHECOMMERCIAL
Eiectrique
INSTRUCCIONES DE INSTALACION- SECADORA HE COMERCIAL
El_ctrica
ISTRUZION!D'INSTALLAZIONE- ASCIUGATRICEHE COMMERCIALE
Elettrica
MDE22PD
W10239206A
www.maytagcommerciaNaundry.com

TABLEOF CONTENTS
DRYER SAFETY ............................................................................ 3
DRYER DISPOSAL ...................................................................... 3
INSTALLATION REQUIREMENTS .............................................. 4
Tools and Parts .......................................................................... 4
Location Requirements .............................................................. 4
E{ectrical Requirements ............................................................ 5
Venting Requirements .............................................................. 6
INSTALLATION INSTRUCTIONS - ELECTRIC DRYER .......... 7
install Leveling Legs.................................................................... 7
Electrical Connection .................................................................. 8
Connect Vent .............................................................................. 8
Complete installation ................................................................ 8
MAINTENANCE INSTRUCTIONS ............................................. 8
REVERSING THE DOOR SWING ............................................. 9
ELECTRONIC CONTROL SETUP .......................................... 11
WAR RAN TY .............................................................................. 15
TABLEDESMATIERES
SECURITE DU SECHE-LINGE ................................................ 16
ELIMINAT}ON DU SECHE-L{NGE .......................................... 16
EXIGENCES D'INSTALLATION ................................................ 17
Outillage et pi_ces .................................................................... 17
Exigences d'emp}acement ...................................................... 17
Speciftcat{ons electriques ....................................................... 18
Exigences concemant revacuat}on .......................................... 19
INSTRUCTIONS D'INSTALLAT{ON - SECHE-LINGE
ELECTRIQUE ............................................................................ 21
installation des pieds de nivetlement ........................................ 21
Raccordement electrique ........................................................ 21
Raccordement du conduit d'evacuation ................................ 21
Achever I'instatlation ................................................................ 22
INSTRUCTIONS D'ENTRETIEN ............................................... 22
INVERS{ON DU SENS D'OUVERTURE DE LA PORTE ......... 23
REGLAGE DE LA CARTE
DE CIRCUITS ELECTRONIQUES .......................................... 25
GARANTIE ................................................................................ 29
P
INDICE
SEGURIDAD DE LA SECADORA ............................................ 30
ELIMINACI6N DE LA SECADORA .......................................... 30
REQUISITOS DE INSTALACION ............................................ 31
Piezas yherramientas .......................................................... 31
Requisitos de ubicaci6n ........................................................ 31
Requisitos electricos ............................................................ 32
Requisitos de ventilaci6n .................................................... 33
INSTRUCCIONES DE INSTALACION -
SECADORA ELECTRICA ........................................................ 34
Instalaci6n de las paras nivetadoras .................................... 34
Cone×i6n electrica ................................................................ 35
Cone×i6n del conducto de escape ...................................... 35
Complete la instataci6n ........................................................ 35
INSTRUCCIONES DE MANTENIMIENTO ............................. 35
COMO INVERT{R EL SENTIDO DE APERTURA
DE LA PUERTA ....................................................................... 36
PROGRAMACION DEL CONTROL ELECTRONICO ............ 38
GARANTIA ................................................................................ 42
INDICE
SICUREZZA DELL'ASCIUGATRICE ........................................ 43
L'ELIMINAZIONE DELL'ASCIUGATRICE .................................. 43
REQUIS{TI D'INSTALLAZIONE ................................................ 44
Attrezzi e componenti .............................................................. 44
Requisiti di ubicazione ............................................................ 44
Requisiti elettrici ...................................................................... 45
Requisiti di scarico .................................................................. 46
ISTRUZIONI D'INSTALLAZIONE - ASCIUGATRICE
ELETTRICA ............................................................................ 47
Instatlazione dei piedini di regolazione .................................... 47
Connessione etettrica .............................................................. 48
Connessione dello scarico ...................................................... 48
Comptetamento dell'instatlazione ............................................ 48
ISTRUZIONI DI MANUTENZIONE ......................................... 48
INVERSIONE DELLA ROTAZIONE D{ APERTURA ............... 49
CONFIGURAZIONE DEI CONTROLLI ELETTRONICl .......... 51
GARANZIA .................................................................................. 55

DRYERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manua{ and on your appliance. Always read and obey a{{ safety
messages.
This is the safety a{ert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
AI{ safety messages wi{{ fo{{ow the safety a{ert symbo{ and either the word "DANGER" or "WARN{NG."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
AHsafety messages will tell you what the potential hazard is, te{I you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
FOR YOUR SAFETY
1. Do not use or store petrol or other flammable materials in this appliance or near this appliance.
2. Do not spray aerosols in the vicinity of this appliance while it is in operation.
3. Do not modify this appliance.
DRYERDISPOSAL
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment
(WEEE).
By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
3

INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Tools needed:
[] 200 mm (8") or 250 mm [] 8 mm (-%o")socket wrench
(10") Pipe wrench [] Utility knife
[] 200 mm (8") or 250 mm [] Vent clamps
(10") Adjustable wrench [] Sealing compound gun
[] Flat-blade screwdriver and sealing compound (for
[] Phillips screwdriver installing new exhaust vent)
[] Adjustable wrench that [] Pliers
opens to 25 mm (1") or [] Stiff-bladed putty knife
hex-head socket wrench
[] Level
Parts supplied:
Remove parts bag from dryer drum. Check that all parts were
included.
[] Foot boot (4) [] PN models: Card reader
[] Dryer foot (4) bezel, card reader wire
harness, hardware
[] PD models: Cam for
service door lock
NOTE: The circuit diagram for this dryer is located inside the
lower front panel, within the Tech Sheets.
Technical
Specifications:
220 -240 v, 50 Hz. AC Clothes Capacity: 9 Kg Max.
Explosion Hazard
Keep flammable materials and vapors, such as petrol,
away from dryer.
Do not install in agarage.
Failure to do so can result in death, e×plosion, or fire.
IMPORTANT: Observe all governing codes and ordinances.
[] Check code requirements: Some codes limit or do not permit
installation of clothes dryers in garages, closets, or sleeping
quarters. Contact your local building inspector.
[] Do not install on carpet.
NOTE: The dryer must not be installed in an area where it will be
exposed to water and/or weather.
Recessed Area and Closet Installation instructions
This dryer may be installed in a recessed area or closet. This
dryer must not be installed behind a lockable door, a sliding door,
or a door with a hinge on the opposite side to that of the dryer.
The installation spacing is in millimeters and is the minimum
allowable. Additional spacing should be considered for ease
of installation, servicing, and compliance with local codes
and ordinances.
If installed in a closet with a door, the minimum unobstructed air
opening in the top and bottom is required. Louvered doors
with equivalent air openings are acceptable.
The dryer must be exhausted outdoors.
No other fuel-burning appliance may be installed in the same
closet as the dryer.
Minimum Installation Clearances
381 mm
Os")
o o
EZ3_-.-
Ornrn _ Ornm
(o") "--_ (o")
Recessed front view
356 rnm
(14") max
Closet
door
J
cl
/.... I
....... 0ram
(0")
_1 ]_2s mm11")
Closet side view
Additional clearances for wall, door, and floor moldings may be required or if
external exhaust elbow is used.
(48 in._)
Front
view
(24in._)
0
L
76 mm (3")
--F
closet
door
76 mm (3")
*Opening is the minimum
for a closet door. Louvered
doors with equivalent air
openings are acceptable.

Product Dimensions 686 mm (27") dryer
686 mm
(27") m===t
25 mm
(1") FRONT VIEW
ELECTRIC
102mm(4")
dia.
-,_358 mm_.._
(14")
BACK VIEW
t
715 mm
- ,
This dryer is supplied without an electric cord and plug. It must
be connected by a competent electrician to a single-phase
electricity supply at the voltage shown on the dataplate, using a
suitable fixed wiring installation in accordance with local and
national wiring regulations.
[] A 3-wire circular cord of minimum conconductor size 2.5 mm2
cross-section area should be used.
[] A 30A supply fuse should be used, and a switch having
a contact separation in both poles that provides full
disconnection under over-voltage category Ill conditions
must be incorporated into the fixed wiring in accordance with
local wiring regulations. The dryer should be positioned so
that the disconnection switch is easily accessible to the user.
[] A cord clamp bush is provided on the dryer, and should be
tightened on completion of wiring. The electrical mains
terminals are located behind the small rear access panel
(terminal block cover), and connections should be made in
accordance with the terminal markings. Remember to replace
the terminal access panel (terminal block cover).
NOTE: In accordance with the European EMC Directive
(2004/108/EC), the maximum electricity supply system
impedance to which the electric dryer should be connected
is declared to be 0.29 Ohm + j0.18 Ohm.
Electric Shock Hazard
This is a3=wire appliance which must be earthed.
Do not earth to a gas pipe.
Failure to follow these instructions could result in
death, fire, or serious injury.
203 mm
(8")
921 mm
(36i/4")
25 mm
(1")
736 mm
,(29) 695 mm
_i(27114,,)
/1
SIDE VlEW
If codes permit and an additional earth bond wire is used, it is
recommended that a qualified electrician determine that the earth
bond path is adequate.
AUSTRALIA ONLY
For Australia, each single electric dryer is fitted with a cord
and plug, with conductors of 2.5 mm2cross sectional area,
and should be plugged into a suitable electrical socket at the
voltage shown on the dataptate. Do not use extension lead
assemblies on commercial installations. If the supply cord is
damaged, it must be replaced with a specially terminated cord
by an authorized service agent or a similarly qualified person in
order to avoid a hazard. Each electric dryer for other countries
is supplied without an electric cord and plug.
Recommended Earthing Method
[] It is your responsibility to contact a qualified electrical installer
to ensure that the electrical installation is adequate and in
conformance with all local codes and ordinances.
5

Fire Hazard
Use aheavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
WARNING: To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
[] Adequate ventilation has to be provided to avoid the backflow
of gases into the room from appliances burning other fuels,
including open fires (i.e. available airflow into the room should
match airflow out from the room).
[] The dryer vent must not be discharged into a flue which is
used for exhausting fumes from appliances burning gas or
other fuels, chimney, wall, ceiling, or a concealed space of
a building, or any other vent used for venting.
[] Do not use an exhaust hood with a magnetic latch.
[] Do not install flexible metal vent in enclosed walls, ceilings,
or floors.
[] 102 mm (4") heavy metal vent and clamps must be used.
[] Use clamps to seat all joints. Vent must not be connected
or secured with screws or other fastening devices which
extend into the interior of the vent and catch lint. Do not use
duct tape.
iMPORTANT: Observe all governing codes and ordinances.
Use a heavy metal vent. Do not use plastic or metal foil vent.
Rigid metal vent is recommended to avoid crushing
and kinking.
Flexible metal vent must be fully extended and supported when
the dryer is in its final position. Remove excess flexible metal
vent to avoid sagging and kinking that will result in reduced
airflow and poor performance.
An exhaust hood should cap the vent to keep rodents and
insects from entering the building.
Exhaust hood must be at least 305 mm (12") from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks, or bushes).
If using an existing vent system, clean lint from the entire length
of the system and make sure exhaust hood is not plugged with
lint. Replace any plastic or metal foil vent with rigid metal or
flexible metal vent.
Plan installation to use the fewest number of elbows and turns.
ExhaustAir Flow
A.Good
B.Better
Allow as much room as possible when using elbows or making
turns. Bend vent gradually to avoid kinking.
Vent outlet is located at the center of the bottom dryer back.
The vent can be routed up, down, left, right, behind the dryer,
or straight out the back of the dryer.
Vent System Length
Maximum length of vent system depends upon the type of vent
used, number of elbows, and type of exhaust hood.
Maximum Vent Length
102 mm (4") Exhaust Hoods
Box Louvered 64 mm (2V/') Angled
Rigid MetalVent _ (_
No. of 900 turns Box Hood and Louvered Style Angled Hood Style
0 39.6 m (130 ft.) 39.3 m (129 ft.)
1 38.1 m (125 ft.) 36.3 m (119 ft,)
2 35.1 m (115 ft.) 33.2 m (109 ft,)
3 32.3 m (106 ft.) 30.5 m (100 ft.)
4 98 m (98 ft.) 28 m (92 ft.)
If dryer is installed in a confined area, such as a bedroom,
bathroom, or closet, provision must be made for enough air
for combustion and ventilation. (Check governing codes and
ordinances.) See "Recessed Area and Closet Installation
Instructions" in the "Location requirements" section.
A 102 mm (4") outlet hood is preferred. However, a 64 mm
(2_/2") outlet exhaust hood may be used. A 64 mm (2W')
outlet creates greater back pressure than other hood types.
For permanent installation, a stationary vent system is required.

Multiple Dryer Venting
[] A main vent can be used for venting a group of dryers. Main
vent should be sized to remove 5663 I/min (200 CFM) of air
per dryer. Large-capacity lint screens of proper design may be
used in the main vent if checked and cleaned frequently. The
room where the dryers are located should have make-up air
equal to or greater than the airflow of all the dryers in the
room.
[] A back-draft damper kit is needed and is available from a
commercial laundry distributor; it should be installed in the
vent of each dryer to keep exhausted air from returning
into the dryers and to keep the exhaust in balance within
the main vent. Unobstructed return air openings are required.
Each vent should enter the main vent at an angle pointing in the
direction of the airflow. Vents entering from the opposite side
should be staggered to reduce the exhausted air from interfering
with the other vents.
The maximum angle of each vent entering the main vent should
be no more than 30°.
A. Individual dryer vent
B. Main vent
Keep air openings free of dry cleaning fluid fumes. Fumes create
acids which, when drawn through the dryer heating units, can
damage dryers and items being dried.
A clean-out cover should be located on the main vent for periodic
cleaning of the vent system.
If an exhaust hood cannot be used:
Min. 300 mm (12") clearance
above any accumulation
of snow, ice, or debris such
as leaves.
A. Exhaust hood or elbow
B. Wall
C. Main collector vent
D. Horizontal vent
E. 180°sweep elbow
EVertical vent
G. Roof
610 mm(24")
min. above
highestpoint
of building G
C
The outside end of the main vent should have a sweep elbow
directed downward. If the main vent travels vertically through the
roof, rather than through the wall, install a 180 ° sweep elbow on
the end of the vent at least 610 mm (2 ft.) above the highest part
of the building. The opening in wall or roof shall have a diameter
13 mm (1_,)larger than the vent diameter. The vent should be
centered in the opening.
Do not install screening or cap over the end of the vent.
INSTALLATIONINSTRUCTIONS-ELECTRICDRYER
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
NOTE: Slide dryer onto cardboard or hardboard before moving
to avoid damaging floor covering.
1. Using two or more people, move dryer to desired installation
location.
2. Take tape off front corners of dryer. Open dryer and remove
the literature and parts packages. Wipe the interior of the
drum thoroughly with a damp cloth.
3. Take two of the cardboard corners from the carton and place
them on the floor in back of the dryer. Firmly grasp the body
of the dryer and gently lay it on its back on the cardboard
corners.
4. With one of the legs in hand, check the ridges for a diamond
marking. That's how far the leg is supposed to go into the
hole.
5. Start to screw the leveling legs into the holes by hand. (Use
a small amount of liquid detergent to lubricate the screw
threads so it is easier to turn the legs.) Use a 1" (25 mm)
wrench or socket wrench to finish turning the legs until you
reach the diamond mark. Then fit a protective foot boot over
each foot.
Now stand the dryer up.
6. Remove cardboard or hardboard from under dryer. Adjust the
legs of the dryer up or down until the dryer is level.
7

Electric Shock Hazard
This is a3-wire dryer which must be earthed.
Securely tighten all electrical connections.
Failure to do so can result in death, fire, or
electric shock.
This dryer is supplied without an electric cord and plug;
it must be connected by a competent electrician.
In Australia, each single electric dryer is fitted with a cord
and plug. See "Electrical Requirements."
1. Using a 102 mm (4") clamp, connect vent to exhaust outlet
in dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured
to exhaust hood with a 102 mm (4") clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
1. With dryer in final position, place level on top of the dryer,
first side to side; then front to back. If the dryer is not level,
adjust the legs of the dryer up or down until the dryer is level.
2. Switch on power supply.
3. Check dryer operation:
Press the selection button for a full cycle and let the dryer run
for at least five minutes. Dryer will stop when time is used up.
NOTE: Dryer door must be closed for dryer to operate.
When door is open, dryer stops, but timer continues to run.
To restart dryer, close door and press a cycle button.
4. Start the dryer and allow it to complete a full cycle to make
sure it is working properly.
MAINTENANCEINSTRUCTIONS
Maintenance instructions:
mClean lint screen after each cycle.
mRemoving accumulated lint:
•From inside the dryer cabinet:
Lint should be removed every 2 years or more often,
depending on dryer usage. Cleaning should be clone
by a qualified person.
•From the exhaust vent:
Lint should be removed every 2 years, or more often,
depending on dryer usage.
If dryer does not operate, check the following:
[] Electric supply is connected.
[] Circuit breaker is not tripped or fuse is not blown.
[] Door is closed. Listen closely to hear door switch(es) activate.
[] Selected cycle button has been pressed firmly and display
shows cycle time.
If you need assistance:
Contact your authorized Maytag Commercial Laundry distributor
or visit: www.MaytagCommerciatLaundry.com. When you call,
you will need the dryer model number and serial number.
Both numbers can be found on the serial-rating plate located
on your appliance.

REVERSINGTHEDOORSWING
Door swing can be changed from a right-side opening to left-side
opening, if desired.
Place a towel or soft cloth on top of the dryer or work space
to avoid damaging the surface.
5. Rotate outer door 180 °.
1.
2.
3.
Remove 3 of the 4 screws that hold the door hinge on the
front panel of the dryer. Partially loosen the remaining screw
with keyhole opening and lift the door off the screw.
\
Loosen
screw
with
keyhole
opening
A. Dryer front panel
B. Door assembly
Lay the door assembly on a previously prepared flat surface
with the inside (inner door assembly) facing up.
Remove the 6 Phillips head screws to release the outer door
assembly from the inner door assembly, as indicated below.
See illustration. It is important that you remove only the 6
indicated screws.
4. Lift the inner door assembly off the outer door assembly.
(J
1. Use a small flat-blade screwdriver to remove 2 plug strips
from the inner door. Slide the head of the screwdriver under
the plugs, being certain not to scratch the inner door surface.
Lift up.
2. Remove the 4 screws that attach to the inner door hinge and
move the hinge to the other side. Reinstall the 4 screws.
,\
Door hinge
3. Reinstall plug strips on opposite side of the inner door.
4. Check for fingerprints on the glass. Clean glass if necessary.
9

5. Place the inner door assembly inside the outer door assembly.
To fit correctly, the inner door assembly edge fits completely
inside the outer door assembly edge.
2. Remove the strike using a Phillips screwdriver.
6.
1.
Reassemble the inner and outer door assemblies with the
6 screws.
Use a small flat-blade screwdriver to remove ptug strip from
the dryer door opening. Slide the head of the screwdriver
under the plugs, being certain not to scratch the dryer
surface. Lift the plastic strip from the dryer slowly to avoid
distortion of the ptug strip.
3. Insert strike on the opposite side.
1.
2.
3.
Reattach door to dryer front panel with the 4 screws.
Partially install the screw with keyhole opening first, and fit
the keyhole opening in the hinge over the screw. Then install
the remaining 3 screws and tighten alt 4 screws.
Instafl this
screw first
A. Dryerfront panel
B. Door assembly
Check for fingerprints on the glass. Clean glass if necessary.
Close door and check that it latches securely.
A. Plug strip
B. Door strike
10