Maytag MHN33PD User manual

INSTALLATION INSTRUCTIONS
(ORIGINAL INSTRUCTIONS)
COMMERCIAL FRONT-LOAD WASHER
MODEL: MHN33PD, MHN33PR
APPROVAL TYPE: NAW130P
W11449285A
INSTRUCTIONS D'INSTALLATION
(INSTRUCTIONS ORIGINALES)
LAVE-LINGE COMMERCIAL ÀCHARGEMENT FRONTAL
MODÈLE: MHN33PD, MHN33PR
TYPE D'APPROBATION: NAW130P
INSTRUCCIONES DE INSTALACIÓN
(INSTRUCCIONES ORIGINALES)
LAVADORA COMERCIAL DE CARGA FRONTAL
MODELO: MHN33PD, MHN33PR
TIPO DE HOMOLOGACIÓN: NAW130P

2
TABLE OF CONTENTS
WASHER SAFETY....................................................................................3
WASHER DISPOSAL................................................................................4
INSTALLATION REQUIREMENTS...........................................................5
Tools and Parts......................................................................................5
Options..................................................................................................5
Specications........................................................................................5
Location Requirements .........................................................................6
Drain System.........................................................................................6
Electrical Requirements.........................................................................7
Power Cord Replacement Instructions .................................................8
INSTALLATION INSTRUCTIONS.............................................................9
Remove Transport System ....................................................................9
Connect the Inlet Hoses......................................................................10
Connect the Drain Hose......................................................................11
Secure the Drain Hose ........................................................................11
Level the Washer.................................................................................11
Payment System Setup.......................................................................12
Complete Installation...........................................................................12
USER & SETUP INSTRUCTIONS..........................................................12
General User Information ....................................................................12
Control Setup Procedures...................................................................13
Setup Codes .......................................................................................13
WASHER CARE......................................................................................17
Cleaning Your Washer .........................................................................17
Water Inlet Hoses ................................................................................17
ASSISTANCE OR SERVICE...................................................................17
Accessories.........................................................................................17
Model Nomenclature
MHN - Maytag
33 - Model Type Number
PD - Electronic Control - Coin Drop Enabled
PR - Electronic Control - Card Ready
TABLE DES MATIÈRES
SÉCURITÉ DU LAVE-LINGE .................................................................. 18
MISE AU REBUT DU LAVE-LINGE ........................................................ 19
EXIGENCES D'INSTALLATION.............................................................. 20
Outils et pièces..................................................................................... 20
Options................................................................................................. 20
Spécifications....................................................................................... 20
Exigences relatives à l'emplacement ................................................... 21
Système de vidange............................................................................. 21
Exigences électriques .......................................................................... 22
Instructions de remplacement du cordon d'alimentation 23
INSTRUCTIONS D'INSTALLATION ....................................................... 24
Dépose du système de transport......................................................... 24
Raccordement des tuyaux d'arrivée .................................................... 25
Raccordement du tuyau d'évacuation ................................................. 26
Immobilisation du tuyau d'évacuation ................................................. 26
Mise à niveau du lave-linge.................................................................. 26
Configuration du système de paiement ............................................... 27
Finalisation de l'installation .................................................................. 27
INSTRUCTIONS D'UTILISATION ET DE CONFIGURATION 27
Informations générales pour l'utilisateur .............................................. 27
Procédures de configuration des commandes .................................... 28
Codes de configuration........................................................................ 28
ENTRETIEN DU LAVE-LINGE ................................................................ 32
Nettoyage du lave-linge ....................................................................... 32
Tuyaux d'arrivée d'eau......................................................................... 32
ASSISTANCE OU SERVICE APRÈS-VENTE ........................................ 32
Accessoires .......................................................................................... 32
Nomenclature du modèle
MHN - Maytag
33 - Numéro Type Modèle
PD - Commande électronique - peut fonctionner avec des pièces
de monnaie
PR – Commande électronique - peut fonctionner à carte
Nomenclatura de los modelos
MHN - Maytag
33 - Número del tipo de modelo
PD - Control electrónico - Habilitado para tragamonedas
PR - Control electrónico - Preparado para tarjeta
TABLA DE CONTENIDOS
SEGURIDAD DE LA LAVADORA........................................................... 33
ELIMINACIÓN DE LA LAVADORA........................................................ 34
REQUISITOS DE INSTALACIÓN........................................................... 35
Herramientas y piezas......................................................................... 35
Opciones ............................................................................................. 35
Especificaciones ................................................................................. 35
Requisitos de ubicación...................................................................... 36
Sistema de desagüe............................................................................ 36
Requisitos eléctricos ........................................................................... 37
Instrucciones para la sustitución del cable de alimentación 38
INSTRUCCIONES DE INSTALACIÓN................................................... 39
Eliminación del sistema de transporte ................................................ 39
Conexión de las mangueras de entrada ............................................. 40
Conexión de la manguera de desagüe ............................................... 41
Fijación de la manguera de desagüe .................................................. 41
Nivelar la lavadora............................................................................... 41
Configuración del sistema de pago .................................................... 42
Instalación completa ........................................................................... 42
INSTRUCCIONES DE USO Y PROGRAMACIÓN................................. 42
Información general del usuario.......................................................... 42
Procedimientos de programación del control..................................... 43
Códigos de programación................................................................... 43
CUIDADO DE LA LAVADORA ............................................................... 47
Limpieza de la lavadora....................................................................... 47
Mangueras de entrada de agua .......................................................... 47
ASISTENCIA O SERVICIO TÉCNICO ................................................... 47
Accesorios........................................................................................... 47

3
The washer shall be disconnected from its power source during service and when replacing parts. If the removal of plug is
foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any of the
points to which they have access that the plug remains removed.
If this is not possible, due to the construction of the washer or its installation, a disconnection with a locking system in the
isolated position shall be provided.
WASHER SAFETY
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of re, electric shock, or injury to persons when using the washer, follow basic precautions, including the
following:
nRead all instructions before using the washer.
nUnder certain conditions, hydrogen gas may be produced in a
hot water system that has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has
not been used for such a period, before using the washer, turn
on all hot water faucets and let the water ow from each for
several minutes. This will release any accumulated hydrogen
gas. As the gas is ammable, do not smoke or use an open
ame during this time.
nBefore the washer is removed from service or discarded,
remove the door or lid.
nDo not install or store the washer where it will be exposed to
the weather.
nDo not repair or replace any part of the washer or attempt any
servicing unless specically recommended in this manual or
in published user-repair instructions that you understand and
have the skills to carry out.
nDo not wash or dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with petrol, dry-cleaning
solvents, other ammable, or explosive substances as they
give off vapors that could ignite or explode.
nDo not add gasoline, dry-cleaning solvents or other ammable,
or explosive substances o the wash water. These substances
give off vapors that could ignite or explode.
nDo not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children. Cleaning and user maintenance shall not be made
by children without supervision. Children of less than 3 years
should be kept away unless continuously supervised.
nTo pause/stop a wash cycle, hold the STOP/PAUSE button for
approximately 2seconds until the machine enters the pause/
stop state.
nThis appliance is intended, but not limited, to be used in public
areas.
nThis washer/dryer is not intended for use by persons (including
children) with reduced physical, sensory, or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning use of the dryer by a
person responsible for their safety.
nDo not reach into the washer if the tub, agitator, or drum is
moving.
nThe appliance must be disconnected from its power source
during service and when replacing parts.
nDo not tamper with controls.
nIf the supply cord is damaged, it must be replaced by the
manufacturer, its service agent, or similarly qualied persons in
order to avoid a hazard.
nFabric softeners, or similar products, should be used as
specied by the fabric softener instructions.
SAVE THESE INSTRUCTIONS
-CONTINUED ON NEXT PAGE-

SAVE THESE INSTRUCTIONS
WASHER DISPOSAL
nWARNING: The appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by a utility.
nVentilation openings in the base shall not be obstructed by a
carpet or similar object.
nThe new hose-sets supplied with the appliance are to be used. Old
hose-sets should not be reused.
nOnly authorised spare parts shall be used in the event of failure.
nSee “Electrical Requirements” section for earthing instructions.
nIf the cord set is damaged, it must be replaced by a special cord set
available from the manufacturer or its service agent.
nAll service and installation operations shall be performed by a
Maytag service person, qualied electrician or similarly qualied
person.

5
Alternate Parts
Your installation may require additional parts. If you are interested
in purchasing one of the items listed here, contact your
authorized Maytag distributor.
If you have You will need to buy
Laundry tub or standpipe
taller than 2.4 m (96") Sump pump system (if not already available)
Overhead sewer Standard 76L (20gallons) ,
762 mm (30") tall drain tub or utility
sink and sump pump (available
from local plumbing suppliers)
Detachable power supply cord -
see Electrical Requirements
Floor drain Siphon break, Part Number
285834; additional drain hose,
Part Number 8318155; and
connector kit, Part Number 285835
Drain hose too short 1.2m (4ft) drain hose extension
kit, Part Number DRNEXT4
Options
Pedestal
You have the option of purchasing pedestals separately for this
washer. The pedestal will add to the total height of the washer.
Optional pedestal
Pedestal
Height Approximate height with washer Color Part Number
73 mm (27⁄8") 1207 mm (47.5") White WHP0400VW
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer drum.
Tools & Parts Needed:
Specications
These units are sold in multiple regions with different
requirements for measuring capacity. Below are a few of
the valid forms of measure posted on this product:
Dry Linen Capacity: A weight measure that reects a minimum
threshold for dry volume capacity that is needed for import tariff
purposes.
IEC Capacity: The capacity measure that represents the
maximum capacity of dry linens and textiles which the
manufacturer declares can be treated in a specic cycle.
Dry Linen Capacity
10.5 kg (23 lbs)
IEC Capacity
10.5 kg (23 lbs)
Sound Level
LpA: 58 dB(A) (KpA+/-10 dB(A))
INSTALLATION
REQUIREMENTS
†TORX and T20 are registered trademarks of Acument Intellectual
Properties, LLC.
AB
DE
C
H
F
G
A. Pliers open to 19/16" (39 mm)
B. 1/2" (13 mm) Open end wrench
C. 9/16" (14 mm) Open end wrench
D. TORX T20†security screwdriver
E. 1/4" (6.3 mm) Nut driver
F. Level
G. Wood block
H. Ruler or measuring tape
Parts Supplied (actual parts supplied depends on model):
IJ
M
N
P
K
L
O
Q
I. Drain hose with clamp, u-form
J. Removable tie strap
K. Water inlet hoses (2)
L. Inlet hose washers (4)
M. Transit bold hole plug (4)
N. Card reader bezel (on some models)
O. Service door lock cam (on some models)
P. Screws (on some models)
Q. Power cords (2)

Location Requirements
NOTE: This washer is intended to be used in public areas.
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a
basement, laundry room, or recessed area. See “Drain System.”
Companion appliance location requirements should also be
considered. Proper installation is your responsibility.
You will need:
■A water heater set to deliver 49°C (120°F) water to the
washer.
■An earthed electrical outlet located within 1.8 m (6 ft) of
where the power cord is attached to the back of the washer.
See “Electrical Requirements.”
■Hot and cold water taps located within 1.2 m (4 ft) of
the hot and cold water ll valves and water pressure of
137.9–689.6kPa (20–100psi).
■A level oor with a maximum slope of 25 mm (1") under
entire washer. Installing the washer on soft oor surfaces,
such as carpets or surfaces with foam backing, is not
recommended.
■A sturdy and solid oor to support the washer with a total
weight (water and load) of 180 kg (400 lbs).
Do not operate your washer in temperatures below 0°C (32°F).
Some water can remain in the washer and can cause damage in
low temperatures.
Installation clearances
■The location must be large enough to allow the washer door
to be fully opened.
■Additional spacing should be considered for ease of
installation and servicing. The door opens more than 90° and
is not reversible.
■Additional clearances might be required for wall, door, and
oor moldings.
■Additional spacing of 25 mm (1") on all sides of the washer is
recommended to reduce noise transfer.
■Companion appliance spacing should also be considered.
Washer Dimensions
A oor drain should be provided under the bulkhead.
Prefabricated bulkheads with electrical outlets, water inlet lines,
and drain facilities should be used only where local codes permit.
1282 mm
(501/2")
961 mm
(3713/16")
686 mm
( 27")
732 mm
(2813/16")
1134 mm
(445/8")
Door is not reversible
Drain System
The washer can be installed using the standpipe drain system
(oor or wall), the laundry tub drain system, or the oor drain
system. Select the drain hose installation method you need. See
“Tools and Parts.”
Standpipe drain system – wall or oor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
50 mm (2"). The minimum carry-away capacity can be no less
than 45.5 L (12 gallons) per minute per washer.
The top of the standpipe must be at least 762 mm (30") high and
no higher than 2.4 m (96") from the bottom of the washer.
Laundry tub drain system (View C)
The laundry tub needs a minimum 76 L (20 gallons) capacity. The
top of the laundry tub must be at least 762 mm (30") above the
oor.
Floor drain system (View D)
The oor drain system requires a siphon break that may be
purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 710mm (28") from the
bottom of the washer. Additional hoses might be needed.
762 mm
(30" min.)
762 mm
(30")
minimum
AB
762 mm
(30" min.)
710 mm
(28" min.)
C
D
762 mm (30")
minimum
710 mm (28")
minimum

7
Electrical Requirements
■A 220–240 V, 50 Hz AC only, fused electrical supply is
required. A time-delay 10–16 A fuse or circuit breaker is
recommended.
■A detachable 3 conductor, 250 V, 10 A, 1.0 mm2(18 AWG)
minimum, power supply cord, 1800 mm (6 ft) long (minimum),
with one end terminated with an IEC 60320-1 C13 connector,
the other end terminated in a 3 prong, earthing-type plug
meeting the local, national, and/or regional approval
authority/safety agency standards is required. Approved
Maytag power supply cords are available for order for
specic regions per the Power Cord Selection table.
■To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, earthing-type outlet, earthed
in accordance with local codes and ordinances. If a mating
outlet is not available, it is the personal responsibility and
obligation of the customer to have the properly earthed outlet
installed by a qualied electrician.
■If codes permit and a separate ground wire is used, it is
recommended that a qualied electrician determine that the
earth path is adequate.
■If the supply cord is damaged, it must be replaced by a
special cord or assembly available from the manufacturer or
its service agent.
■Do not earth to a gas pipe.
■Check with a qualied electrician if you are not sure the
washer is properly earthed.
■Do not have a fuse in the neutral or earth circuit.
■Only a Maytag service person, qualied electrician, or
similarly qualied person shall replace a power cord or
perform service on the electrical power supply in accordance
with these instructions and local codes and regulations.
NOTE: Electrical safety standards: The manufacturer has
chosen compliance with IEC/EN.60335 standards as the most
appropriate for this product.
■Sound Pressure Level, LpA: 58 dbA (uncertainty,
KpA: +/-3.6 dbA)
POWER CORD SELECTION
Part Number IEC Plug Type* Intended
Counties/Region
W11318406
(fused 13A)
G
United Kingdom,
Ireland, Cyprus,
Malaysia, Malta,
Nigeria, Singapore,
Hong kong, Saudi
Arabia, UAE, GCC
states, others (BS1363)
W11318407
E,F Suhuko
(CEE 7/7)
EU, Belgium, Chile,
Egypt, France,
Indonesia, Jordan,
Rep. of Korea,
Paraguay, Russia,
Thailand, Uruguay,
Ukraine, Vietnam,
others
W11318408 IAustralia, China, New
Zealand, Papua New
Guinea (AS/NZS 3112)
* - https://www.iec.ch/worldplugs/
EARTHING INSTRUCTIONS
This washer must be earthed. In the event of a malfunction
or breakdown, earthing will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This washer requires a cord having an
equipment-earthing conductor and an earthing plug. The
plug must be plugged into an appropriate outlet that is
properly installed and earthed in accordance with all local
codes and ordinances.
WARNING: Improper connection of the equipment-
earthing conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly earthed.
Do not modify the appliance power supply cord or plug – if it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.
■This product is shipped with the AS/NZS 3112 power
cord installed. Additional power cords are supplied with
the product. Refer to the Power Cord Selection table to
determine the power cord required for your region, or if
needed, to order the appropriate approved Maytag power
supply cord.

8
Power Cord Replacement Instructions
The steps in this section shall only be performed by a Maytag
service person, qualied electrician, or similarly qualied person.
1. The appliance shall be disconnected from the power
supply before servicing. Read all instructions before any
disassembly.
2. Remove retaining screw securing power cord assembly to the
product and save for re-installation.
3. Rotate the power cord strain relief bracket within the machine
console and remove at an angle from the opening in the
back panel to expose access to the inner connector. The
inner connector is still connected. Do not put strain on the
conductors while removing the bracket to allow access to the
connector.
Retaining
Screw
4. Disengage the supply connection within the product by
depressing the connector clip to release the power cord from
the appliance.
5. Remove the U-Clip from the strain relief bracket by sliding
downward and save for re-installation.
6. Remove the cord from the strain relief bracket and follow the
cord installation steps 7-12. Save the strain relief bracket for
re-installation.
7. Select the regionally required cord/plug and slot it through the
strain relief bracket.
Press
U-Clip
Strain Relief
Bracket
Power Cord
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Outside Product Inside Product
Twist
Remove at
Angle

9
8. Ensure that the molded strain relief of the power cord is
aligned and inserted all the way into the strain relief bracket
before installing the U-Clip. Once inserted, install the U-Clip
to lock the molded on strain relief of the power cord in
position within the strain relief bracket.
9. Insert the cord into the machine and secure the cord side
connector to the matching machine side connector. Ensure
the connector lock is engaged.
10. While the internal connector is still accessible, perform an
Earthing Continuity Test:
A current of at least 10 A, derived from a source having a
no-load voltage not exceeding 12 V (AC or DC), is passed
between:
n The grounding pin or earthing contact of the plug, and
n The grounding conductor of the appliance side connector
(female);
The voltage drop is measured and the resistance is calculated
and shall not exceed 0.2Ω.
If not found to be properly grounded, contact the
manufacturer. Do not connect to the power supply.
11. Once ground continuity is conrmed, rotate the fully
assembled strain relief bracket and insert it into the opening
in the back panel with the connector side facing inward.
The installer shall ensure:
a) That the screw bore is aligned with the back panel screw
orice.
b) The lip of the strain relief bracket is on the external side of
the metal back panel.
U-Clip
Power cord
Molded
on Strain
Relief
Align Molded
on Strain
Relief with the
Strain Relief
Bracket Key
Appliance Side
Grounding
Conductor
Ground Continuity
Test Location 1
Plug
Grounding
Pin/Conductor
Ground Continuity
Test Location 2
IEC Plug Type CEE 7/7
Type F&E Compatible
IEC Plug
Type G
IEC Plug
Type I
(Australia)
12. Insert the retaining screw from step 1 and secure the cord set
to the back panel. The cord assembly shall not be able to be
pushed inward, pulled outward, or twisted in any fashion that
puts stress on the internal conductors. If not secured, revisit
sections 7-11 and ensure proper installation.
Screw
Bore
Strain Relief
Bracket Lip
Remove Transport System
Maximum packed weight:
PD model: 115 kg (253.53 lbs)
PN/PR model: 111 kg (244.71 lbs)
Maximum unpacked weight:
PD model: 111 kg (244.71 lbs)
PN/PR model: 107 kg (235.89 lbs)
IMPORTANT: Position the washer so that the rear of the washer
is within approximately 900 mm (3 ft) of its nal location.
There are 4 shipping bolts in the rear panel of the washer that
support the suspension system during transportation.
1. Keep the washer in the upright position while removing the
shipping bolts.
Shipping bolt
Shipping bolt with plastic spacer
Shipping bolt
INSTALLATION INSTRUCTIONS

10
2. Using a 13 mm (1/2") wrench, loosen each of the bolts.
3. Once the bolt is loose, move it to the center of the hole and
completely pull out the bolt, including the plastic spacer and
store them in a location for use if the unit needs to be moved
at a later date.
IMPORTANT: If the washer is to be transported at a later date,
call your local service center for new transport bolts if the
original set is misplaced. Machine must be transported in the
upright position. To avoid structural or suspension damage
to your washer, it must be properly set up for relocation by a
certied technician.
4. Close the bolt holes with the 4 transport bolt hole plugs.
NOTE: If the washer is to be transported at a later date, call your
product distributor or installer. To avoid suspension and structural
damage, your washer must be properly set up for relocation by a
trained professional.
Connect the Inlet Hoses
Insert new at washers (supplied) into each end of the inlet
hoses. Firmly seat the washers in the couplings.
NOTE: Use new hoses supplied with the washer. Do not reuse
old hoses.
Connect the inlet hoses to water faucets
Make sure the washer drum is empty.
1. Attach a hose to the hot water faucet. Screw on coupling by
hand until it is seated on the washer.
2. Attach a hose to the cold water faucet. Screw on coupling by
hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
AB
A. Coupling
B. Washer
NOTE: Do not overtighten, use tape, or sealants on the valve.
Damage to the valves can result.
Clear water lines
■Run water through both faucets and inlet hoses, into a
laundry tub, drainpipe, or bucket, to get rid of particles in the
water lines that might clog the inlet valve screens.
■Check the temperature of the water to make sure that the hot
water hose is connected to the hot water faucet and that the
cold water hose is connected to the cold water faucet.
Connect the inlet hoses to the washer
C. Cold water inlet
H. Hot water inlet
1. Attach the hot water hose to the check valve on washer’s
hot (H) water inlet valve. Screw on coupling by hand until it is
seated on the check valve.
2. Attach the cold water hose to the check valve on washer’s
cold (C) water inlet valve. Screw on coupling by hand until it is
seated on the check valve.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the coupling can result.

11
4. Turn on the water taps completely and check for leaks.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates on
the hoses for future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Connect the Drain Hose
Remove drain hose from washer drum
1. Use locking pliers, squeeze hose clamp tabs together and
insert over the end of drain hose.
2. Slide drain hose onto washer connection.
3. Once drain hose is in place, release pliers.
Washer drain system can be installed using a oor drain, wall
standpipe, oor standpipe, or laundry tub.
Laundry tub drain or standpipe drain
Connect the drain hose form to the corrugated drain hose.
To keep drain water from going back into the washer:
■Use the drain hose form, and do not force excess drain hose
into standpipe. Hose should be secure, but loose enough to
provide a gap for air.
■Do not lay excess hose on the bottom of the laundry tub.
Floor drain
You may need additional parts. See Floor drain under “Tools
and Parts.”
Secure the Drain Hose
Drain hose must be secured to stop the hose from moving when
water is pumped out. If the drain hose moves, water may end up
on the oor.
1. Drape the power cord over the washer top.
2. Move the washer to its nal location.
3. Place the drain hose in the laundry tub or standpipe as shown.
See illustrations A and B.
NOTES:
■Do not force excess drain hose back into the rear of the
washer.
■To avoid siphoning, do not seal or put more than
114 mm (4½") of the drain hose into drainpipe or standpipe.
■It is the responsibility of the installer to install and secure the
drain hose into the provided plumbing/drain in a manner that
will avoid the drain hose coming out of, or leaking from, the
plumbing/drain.
Level the Washer
Properly leveling your washer avoids excessive noise and
vibration.
1. Check the levelness of the washer by placing a level on the
top edge of the washer, rst side to side, then front to back.
114 mm
( 41/2")
114 mm
(41/2")
BA
Jam nut
Jam nut

12
If the washer is against a wall, move the washer out slightly
before tipping back. If the washer is not level, rst prop the
front with a wood block and adjust the feet as necessary.
To adjust feet, use a 14 mm (9/16") open-end or adjustable
wrench to turn jam nuts clockwise (as viewed from above) on
feet until they are about 13 mm (1/2") from the washer cabinet.
Then turn the leveling foot counterclockwise to lower the
washer or clockwise to raise the washer. Recheck levelness of
washer and that all four feet are rmly in contact with the oor.
Repeat as needed.
2. Make sure all four feet are stable and resting on the oor.
Then check that the washer is perfectly level (use a level).
3. When washer is level and all four feet are rmly in contact with
the oor, use a 14 mm (9/16") open-end or adjustable wrench
to turn jam nuts counterclockwise (as viewed from above) on
leveling feet tightly against washer cabinet.
IMPORTANT: All four feet must be tightened. If the nuts are
not tight against the washer cabinet, the washer may vibrate.
4. The washer should not move front to back, side to side, or
diagonally when pushed on its top edges.
5. Slide the washer to its nal location.
6. Conrm the levelness of the washer.
Payment System Setup
PD Model Washer is coin payment ready and allows the use of
two different sizes of coins if a dual drop is installed. To set up
the washer for coin payment, acquire a coin drop mechanism
with the appropriate coin sensors. Connect coin sensors to coin
slots 1 and 2, respectively.
Jam nut
Jam nut
1. Door must be closed before cycle selection is made.
2. Press fabric setting keypad for the wash cycle desired. After
the cycle is started, the time will display and count down.
General User Information
‘0 Minutes’ showing in display
This indicates the previous cycle is complete or a machine reset
was performed. Opening the door will restore the display to the
vend price or available state.
Factory Default Setting
Washer is programmed at the factory as follows:
■Normal and Delicates cycles have an 11 minutes wash
period and 2 rinses, with the option of an extra rinse.
■The Powerwash cycle has 3 minutes of Prewash, a
14 minutes wash period and 4 rinses, with the option to
deselect the extra rinse.
Complete Installation
1. Check the electrical requirements. Be sure that you have
the correct electrical supply and the recommended earthing
method. See “Electrical Requirements.”
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Check that you have all of your tools.
4. Dispose of/recycle all packaging materials.
5. Check that the water taps are on.
6. Check for leaks around taps and inlet hoses.
7. Plug into an earthed socket outlet.
8. To test and to clean your washer, measure 1/2 the detergent
manufacturer’s recommended amount for a medium-size load.
Pour the detergent into the detergent dispenser. Select any
cycle and allow the washer to complete one whole cycle.
■$1.75 wash price for Normal and Delicates cycles, $2.00 for
Powerwash (PD models).
■$0.00 wash price (PR models).
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, ‘RESELECT CYCLE’ will ash
in the display, indicating the need for a keypad press to restart
washer.
Door Lock
The door will be locked when the cycle starts. The door will
remain locked until the end of a cycle or approximately 2 minutes
after a power interruption.
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation). As
coins are inserted or debit inputs arrive, the display will change to
acknowledge valid coin or debit inputs.
WARNING
Electrical Shock Hazard
Plug into a grounded (earthed) outlet.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.
USER & SETUP INSTRUCTIONS

13
Control Set-Up Procedures
IMPORTANT: Read all instructions before operating.
■PD Models: Insert service access door key, turn, and lift to
remove service access door.
■PR Models: Once the debit card reader is installed (according
to the reader manufacturer’s instructions), the set-up mode
can only be entered by inserting a set-up card (supplied by
the reader manufacturer) into the card slot. If a set-up card is
not available, diagnostic modes can be entered by removing
connector J4 on the circuit board or by using the Service
Access Code (see Service Access Code section) for PR
washers set up for free vend.
IMPORTANT: Unplug washer or disconnect power before
opening the console. To access connector J4:
■Unplug washer or disconnect power.
■Open console, disconnect plug on J4, close console.
■Plug in washer or reconnect power. The washer is now in
the set-up mode. The lower fabric setting keypads and the
digital display are used to set up the controls. The display can
contain 4 numbers and/or letters and a decimal point. These
are used to indicate the set-up codes and related code values
available for use in programming the washer.
Free Cycles
This is established by setting the cycle price to zero. When this
happens, ‘SELECT CYCLE’ will appear rather than a cycle price.
Display
After the washer has been installed and plugged in, the display
will show “0 MINUTES.” Once the washer has been plugged in
and the washer door opened and closed, the display will show
the price. In washers set for free cycles, the display will ash
“SELECT CYCLE.”
Start Operating Setup
NOTE: Prior to operation, a payment system or an OPL kit must
be installed on PD models as part of the setup.
Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a washer that
operates. Washers are preset at the factory for an 11minutes
wash period and 3 rinses (no extra rinse).
Setup Codes
FOR PR MODELS: The set-up codes are the same as for the
“PD” model except where noted.
The set-up code is indicated by the 1 or 2 left-hand characters.
The set-up code value is indicated by the 2 or 3 right-hand
characters. The rst code shown in each section is the Factory
Default setting.
NOTE: Set-up codes marked with * are able to transfer from one
machine to another machine (must be same model type) via USB
stick.
Code Explanation
6 07
NORMAL
NORMAL CYCLE AMOUNT TO START
(Factory Default)
6 07 Represents the number of Coins or Debit inputs
required to start the cycle. See Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the
UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
6 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
6 07
DELICATES
DELICATES CYCLE AMOUNT TO START
(Factory Default)
6 07 Represents the number of Coins or Debit inputs
required to start the cycle. See Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the
UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
6 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
6 07
POWER
WASH
POWERWASH CYCLE AMOUNT TO START
(Factory Default)
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
How to use the keypads to program controls
1. The POWER WASH – UPPER LEFT keypad is used to adjust
the values associated with set-up codes. Pressing this keypad
will increment the value. Rapid adjustment is possible by
holding this keypad down.
2. The TEMPERATURE – LOWER LEFT keypad is used to adjust
the values associated with set-up codes. Pressing this keypad
will decrement the value. Rapid adjustment is possible by
holding this keypad down.
3. The EXTRA RINSE – LOWER MIDDLE keypad will advance
through the set-up codes. Pressing this keypad will advance
to the next available set-up code. Holding this keypad down
will automatically advance through the set-up codes at a rate
of one (1) per second.
4. The DELICATES – UPPER RIGHT keypad is used to select or
deselect options.

14
Code Explanation
6 07 Represents the number of Coins or Debit inputs
required to start the cycle. See Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the
UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
6 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
7 11 WASH LENGTH
7 11 This is the number of minutes for WASH. Washer
comes from the factory preset with 11 minutes.
Choose from 9–17 minutes by pressing the
LOWER
LEFT keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
8 00 ADDITIONAL RINSE OPTION/EXIT SERVICE
MODE
NOTE: This only affects NORMAL and DELICATES cycles.
Additional Rinse is always enabled for POWERWASH.
8 00 Additional Rinse not selected ‘OFF’.
Use this eld to exit Service Mode when entered
via the key dance.
Press and hold the LOWER LEFT keypad to exit
Service Mode.
8 Ar Additional Rinse selected ‘ON’.
Use this eld to exit Service Mode when entered
via the key dance.
Press and hold the LOWER LEFT keypad to exit Service Mode.
Press the LOWER MIDDLE keypad once to advance to next code.
9 00 CYCLE COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
9 00 Not Selected ‘OFF’.
9 0C Selected ‘ON’ and not able to be deselected.
Press the LOWER RIGHT keypad 3 consecutive
times to select ‘ON’. Once selected ‘ON’ it cannot
be deselected.
Press the LOWER MIDDLE keypad once to advance to next code.
1. 00 MONEY COUNTER OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
1. 00 Not Selected ‘OFF’.
1. 00 Selected ‘ON’.
Press the UPPER RIGHT keypad 3 consecutive
times to select ‘ON’ and 3 consecutive times to
remove (Not Selected ‘OFF’.) Counter resets by
going from ‘OFF’ to ‘ON’.
1 C0 Selected ‘ON’ and not able to be deselected.
To select ‘ON’ and not able to be deselected,
rst select ‘ON’, then within 2 seconds, press
the LOWER RIGHT keypad twice,
LOWER LEFT
keypad
once, and exit the set-up mode.
Press the LOWER MIDDLE keypad once to advance to next code.
2. 00 SPECIAL PRICING OPTIONS
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
2. 00 Not Selected ‘OFF’, and next available code will
be A.00.
2. SP Selected ‘ON’. Press the UPPER RIGHT keypad
once for this selection.
Code Explanation
NOTE: If SPECIAL PRICING OPTION is selected, there is
access to codes ‘3.XX’ through ‘9.XX’.
Press the
LOWER MIDDLE keypad once to advance to next
code.
Options to use if SPECIAL PRICING is selected:
3. 07
NORMAL
NORMAL SPECIAL CYCLE AMOUNT TO
START
3. 07 Represents the number of Coins or Debit inputs
required to start the cycle. Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad. Factory default of 7.
3. 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
3. 07
DELICATES
DELICATES SPECIAL CYCLE AMOUNT TO
START
3. 07 Represents the number of Coins or Debit inputs
required to start the cycle. See Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
3. 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
3. 07
POWER
WASH
POWERWASH SPECIAL CYCLE AMOUNT TO
START
3. 07 Represents the number of Coins or Debit inputs
required to start the cycle. See Value of Coin 1.
Adjustable from 0 to 200.
PD models default setting is 7 - PR models
default setting is 0.
Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
3. 00 PR MODELS ONLY: Factory default of 0.
Press the LOWER MIDDLE keypad once to advance to next code.
5. 00 TIME-OF-DAY CLOCK, MINUTES
5. 00 This is the TIME-OF-DAY CLOCK, minute setting;
select 0–59 minutes by pressing the LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
6. 00 TIME-OF-DAY CLOCK, HOURS
NOTE: Uses 24-hour clock.
6. 00 This is the TIME-OF-DAY CLOCK, hour setting;
select 0–23 hours by pressing the LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
7. 00 SPECIAL PRICE START HOUR
NOTE: Uses 24-hour clock.
7. 00 This is the start hour; 0–23 hours. Select START
HOUR by pressing the LOWER LEFT or UPPER
LEFT keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
8. 00 SPECIAL PRICE STOP HOUR
NOTE: Uses 24-hour clock.

15
Code Explanation
8. 00 This is the stop hour; 0–23 hours. Select STOP
HOUR by pressing the LOWER LEFT or UPPER
LEFT keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
9. 10 SPECIAL PRICE DAY
9. 10 This represents the day of the week and whether
special pricing is selected for that day. A number
followed by ‘0’ indicates no selection that
particular day (9.10). A number followed by an ‘S’
indicates selected for that day (9.1S).
Days of the week (1–7) are selected by pressing
the
LOWER LEFT keypad. Press the UPPER
RIGHT keypad once to select special pricing for
each mday chosen.
When exiting set-up code ‘9’, the display must
show current day of week:
DISPLAY DAY OF WEEK CODE (selected)
10 Day 1 = Sunday 1S
20 Day 2 = Monday 2S
30 Day 3 = Tuesday 3S
40 Day 4 = Wednesday 4S
50 Day 5 = Thursday 5S
60 Day 6 = Friday 6S
70 Day 7 = Saturday 7S
Press the LOWER MIDDLE keypad once to advance to next code.
A. 00 VAULT VIEWING OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’.
A. 00 Not Selected ‘OFF’.
A. SC Selected ‘ON’. Press the UPPER RIGHT keypad
once for this selection. When selected, the
money and/or cycle counts will be viewable (if
counter option(s) is selected) when the coin box is
removed.
Press the LOWER MIDDLE keypad once to advance to next code.
b. 05 VALUE OF COIN 1
b. 05 This represents the value of coin 1 in number of
$0.05 increments of the larger coin value.
Example: 5 x $0.05 = $0.25.
By pressing the LOWER LEFT keypad, there is the
option of 1–199 for the number of $0.05
increments.
Press the LOWER MIDDLE keypad once to advance to next code.
C. 20 VALUE OF COIN 2
C. 20
This represents the value of coin 2 in number of
$0.05 increments of the larger coin value.
Example: 20 x $0.05 = $1.00.
Press the LOWER MIDDLE keypad once to advance to next code.
d. 00 COIN SLIDE OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’. Replacement of meter case will
be needed for coin slide mounting.
d. 00 Not Selected ‘OFF’.
Code Explanation
d. CS Selected ‘ON’.
NOTE: This option needs to be set to ‘00’ unless
the meter case has been changed to accept
a coin slide device. Press the UPPER RIGHT
keypad 3 consecutive times for this selection.
When coin slide mode is selected, set ‘b’. equal
to value of vend price in $0.05 increments. Set
set-up code 6 xx (regular cycle price) and set-up
code 3.xx (special cycle price) to number of slide
operations. If the installer sets-up ‘CS’ and a coin
drop mechanism is installed, the washer will not
register coins that are inserted.
Press the LOWER MIDDLE keypad once to advance to next code.
E. 00 ADD COINS OPTION
This option is either SELECTED ‘ON’ or NOT
SELECTED ‘OFF’. This option causes the
customer display to show the number of coins
(coin 1) to enter, rather than the dollars-and-cents
amount.
E. 00 Not Selected ‘OFF’.
E. AC Selected ‘ON’. Press the UPPER RIGHT keypad 3
consecutive times for this selection.
Press the LOWER MIDDLE keypad once to advance to next code.
H. 00
COOL
COOL TEMPERATURE UPGRADE PRICE
H. 00 Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
H. 00
WARM
WARM TEMPERATURE UPGRADE PRICE
H. 00 Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
H. 00
HOT HOT TEMPERATURE UPGRADE PRICE
H. 00 Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
H. 01
EXTRA
RINSE
EXTRA RINSE UPGRADE PRICE
H. 01 Increase from 0–200 by pressing the UPPER LEFT
keypad and decrease by pressing LOWER LEFT
keypad.
Press the LOWER MIDDLE keypad once to advance to next code.
J. Cd COIN/DEBIT OPTION
J. Cd Both coin and debit selected. Press the UPPER
RIGHT keypad 3 consecutive times for this
selection.
J. C_ Coins selected, debit disabled. Press the UPPER
RIGHT keypad 3 consecutive times for this
selection.
J. _d PR models factory default to J._d. Debit Card
selected, coins disabled. Press the UPPER
RIGHT keypad 3 consecutive times to change this
selection.

16
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number of
cycles in HUNDREDS 1 02 = 200
2 00 Represents the number of
cycles in ONES 2 25 = 25
TOTAL CYCLES = 225
This is “VIEW ONLY” and cannot be cleared.
Press the LOWER MIDDLE keypad once to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 00 Number of dollars in
HUNDREDS 3 01 = $100.00
4 00 Number of dollars in ONES 4 68 = $ 68.00
5 00 Number of CENTS 5 75 = $ 00.75
TOTAL = $168.75
Code Explanation
J. Ed Enhanced Debit is self-selected when a
Generation 2 card reader is installed in the
washer. The Ed option cannot be manually
selected or deselected.
Press the LOWER MIDDLE keypad once to advance to next code.
L. 00 PRICE SUPPRESSION OPTION
This option causes the customer display to show
‘ADD’ or ‘AVAILABLE’ rather than the amount of
money to add. (Used mainly in debit installations.)
L. 00 Not Selected ‘OFF.’
L. PS Selected ‘ON.’ Press the UPPER RIGHT keypad
once for this selection.
Press the LOWER MIDDLE keypad once to advance to next code.
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for
30minutes without further escrow or cycle
activity will be cleared.
n 00 Not Selected ‘OFF’.
n CE Selected ‘ON’. Press the UPPER RIGHT keypad
once for this selection.
Press the LOWER MIDDLE keypad once to advance to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the UPPER RIGHT keypad. Factory
default of 800 rpm.
Press the LOWER MIDDLE keypad once to advance to next code.
A1. 03 PREWASH LENGTH
A1. 03 This is the number of minutes of PREWASH.
Select between 2 and 7 minutes by pressing the
UPPER LEFT keypad to increase or the LOWER
LEFT keypad to decrease.
Press the LOWER MIDDLE keypad once to advance to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of nal high speed
spin. Choose from 3–8 minutes by pressing the
UPPER LEFT keypad to increase or the LOWER
LEFT keypad to decrease.
Press the LOWER MIDDLE keypad once to advance to next code.
A3. 02 NORMAL CYCLE SETTINGS
A3. 02 Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specic settings. Normal is set
to 02 from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
A4. 00 DELICATES CYCLE SETTINGS
A4. 00 Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specic settings. Delicates is set
to 00 from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
A5. OF POWERWASH CYCLE SETTINGS
END OF SETUP PROCEDURES
EXIT FROM SETUP MODE
■PD Models: Reinstall access door.
■PR Models:
– Unplug washer or disconnect power.
– Open console, reinsert plug into Service Connection, close
console.
– Plug in washer or reconnect power.
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. It only functions on washers set up for
0vend price without any Special Pricing setup, and the Coin/
Debit Option must be set to “J._d”. If the washer is not in failure
mode, the door must be opened to proceed.
To enter the Service Access Code, press these keypads in the
following order: 1–upper left, 2–lower right, 3–upper right, 4–lower
left.
NOTE: If the Service Access Code procedure is not completed
properly, as noted above, there is a 15 seconds delay before it
can be attempted again.
There are 3 options to exit from the Service Mode:
1. Power down the washer; then reapply power.
2. Wait 2 minutes without touching any keypads (without
diagnostic modes running).
3. From Set-Up Code 8, press keypad #1 for 4 seconds.
Code Explanation
A5. OF Allows the owner to select the cycle default
options of Water Temperature, Prewash, and
Extra Rinse.
See Table 1 for specic settings. PowerWash is
set to OFF from the factory. The UPPER LEFT and
LOWER LEFT keypads change the values.
Press the LOWER MIDDLE keypad once to advance to next code.

17
Cleaning Your Washer
Cleaning the Door Seal/Bellow
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the colored seal/bellow between the door opening
and the drum for stained areas. Pull back the seal/bellow
to inspect all areas under the seal/bellow and to check for
foreign objects.
A
A. Seal/Bellow
3. If stained areas are found, wipe down these areas of the seal/
bellow, using the procedure that follows.
a) Mix a dilute solution, using 177 mL (3/4 cup) of liquid
chlorine bleach, and 3.8 L (1 gallon) of warm tap water.
b) Wipe the seal/bellow area with the dilute solution, using
a damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let the
washer interior air dry with door open.
IMPORTANT:
■Wear rubber gloves when cleaning for prolonged periods.
■Refer to the bleach manufacturer’s instructions for proper use.
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean the
inside of the washer.
NOTES:
■Read these instructions completely before beginning the
cleaning process.
■If necessary, the cleaning cycle may be interrupted by
pressing the keypad twice. However, this will not immediately
stop the cycle. The washer will continue with several rinse
and drain steps to ensure that all remaining bleach is rinsed
from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items from
the washer.
2. Use liquid chlorine bleach:
Open the dispenser drawer and immediately add 160mL
(2/3cup) of liquid chlorine bleach to the bleach compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 160mL (2/3cup) of bleach will cause product damage
over time.
3. Close the washer door and the dispenser drawer.
4. Enter Set-Up Mode
Press Upper Right Keypad for 2 seconds. P01 will be
displayed. Press Lower Middle Keypad 7 times to advance to
P08. Press Start Keypad.
NOTE: The door will lock and the drum will rotate; then the
door will unlock, lock again, and the cycle will continue.
■The washer will not ll, but the drum will rotate while
the washer runs a short sensing cycle. This will take
approximately 3 minutes.
5. The cycle will determine whether clothing or other items are
in the washer.
a) If no items are detected in the washer, it will proceed
to Step 7.
b) If any items are detected in the washer, “rL” or “F-34”
will be displayed. Then the door will unlock.
■Press to cancel the failure code.
Then repeat steps 1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly, to
allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
■Use only “HE” High Efciency detergent.
■Leave the door slightly open after each cycle to allow for
better ventilation and drying of washer interior.
■Clean the washer monthly using the Washer Maintenance
Procedure, and
160 mL (2/3 cup) of liquid chlorine bleach.
■If the procedure does not sufciently improve the washer
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the Exterior
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the Dispenser Drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Replace the inserts and return the dispenser to the drawer.
Water Inlet Hoses
Replace water inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace water inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your water inlet hoses, mark the date of
replacement on the label with a permanent marker.
ASSISTANCE OR SERVICE
Direct all requests for service to the Maytag Commercial Laundry
Distributor that sold the appliance.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Accessories
Enhance your washer with these premium accessories.
For more high-quality items or to order, contact your authorized
Maytag distributor.
Whirlpool Corporation, Benton Harbor, Michigan 49022, U.S.A.
Manufacturer site: Whirlpool Corporation, 119 Birdseye St., Clyde, OH 43410.
EU representative: Whirlpool EMEA S.p.A., Via Carlo Pisacane n.1 20016 Pero (MI) Italy
WASHER CARE

18
Risque possible de décès ou de blessure grave si vous ne
suivez pas immédiatement les instructions.
Risque possible de décès ou de blessure grave si vous
ne suivez pas les instructions.
Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Votre sécurité et celle des autres est très importante.
Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de
toujours lire tous les messages de sécurité et de vous y conformer.
AVERTISSEMENT
DANGER
Voici le symbole d’alerte de sécurité.
Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous
et à d’autres.
Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou
“AVERTISSEMENT”. Ces mots signifient :
Le lave-linge doit être débranché de sa source de courant électrique durant les interventions de service et le remplacement des
pièces. Si l'on prévoit de retirer la prise, il doit être clairement indiqué qu'il est possible pour l'opérateur de conrmer le retrait de
la prise depuis n'importe quel point d'accès.
Si ce n'est pas possible en raison de la construction ou de l'installation de l'appareil, une déconnexion avec un système de
verrouillage en position isolée sera prévue.
SÉCURITÉ DU LAVE-LINGE
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT: Pour réduire le risque d'incendie, de choc électrique ou de blessure lors de l'utilisation du lave-linge, suivre les
consignes de base suivantes:
nLire toutes les instructions avant d'utiliser le lave-linge.
nDans certaines conditions, un circuit d'eau chaude inutilisé
pendant 2semaines ou plus peut produire de l'hydrogène.
L'HYDROGÈNE EST UN GAZ EXPLOSIF. Si le circuit d'eau
chaude n'a pas été utilisé pendant cette période, ouvrir tous les
robinets d'eau chaude et laisser couler l'eau pendant plusieurs
minutes avant d'utiliser le lave-linge. L'hydrogène gazeux
éventuellement contenu dans le circuit sera ainsi évacué. Vu
que le gaz est inammable, ne pas fumer ni utiliser de amme
nue pendant cette période.
nAvant que le lave-linge ne soit mis hors service ou mis au rebut,
enlever la porte ou le couvercle.
nNe pas installer ou stocker le lave-linge dans un lieu où il serait
exposé aux intempéries.
nNe pas réparer ou remplacer un composant quelconque du
lave-linge et ne pas essayer d'effectuer un entretien, sauf si
cela est spéciquement recommandé dans ce manuel ou dans
un manuel d'instructions de réparation destiné à l'utilisateur. Il
est alors essentiel que la personne concernée comprenne ces
instructions et soit compétente pour les exécuter.
nNe pas laver ni sécher des articles qui ont été préalablement
nettoyés, lavés, trempés ou tachés avec de l'essence,
des solvants de nettoyage à sec ou d'autres substances
inammables ou explosives, car ils dégagent des vapeurs qui
pourraient s'enammer ou exploser.
nNe pas ajouter d'essence, de solvants de nettoyage à sec,
ou d'autres substances inammables ou explosives à l'eau
de lavage. Ces produits dégagent des vapeurs qui pourraient
prendre feu ou exploser.
nNe pas laisser les enfants jouer sur ou à l'intérieur du lave-
linge. Les enfants à proximité du lave-linge pendant son
fonctionnement doivent faire l'objet d'une étroite surveillance.
Le nettoyage et l'entretien par l'utilisateur ne doivent pas être
effectués par des enfants sans surveillance. Les enfants de
moins de 3ans doivent être tenus à l'écart, sauf s'ils sont
surveillés en permanence.
nPour interrompre/arrêter un cycle de lavage, maintenez le bouton
STOP/PAUSE (PAUSE/ARRETÊ) enfoncé pendant environ
2secondes jusqu'à ce que la machine passe en mode pause/arrêt.
nL'appareil est conçu pour une utilisation dans des espaces
publics mais cette utilisation n'est pas exclusive.
nCe lave-linge n'est pas prévu pour être utilisé par des
personnes (y compris les enfants) dont les capacités physiques,
sensorielles ou mentales sont réduites, ou par des personnes
manquant d'expérience ou de connaissances, sauf si elles
peuvent bénécier de surveillance ou ont reçu des instructions
préalables concernant l'utilisation de l'appareil par une personne
responsable de leur sécurité.
nNe pas mettre la main dans le lave-linge si la cuve, l'agitateur ou
le tambour est en mouvement.
CONSERVER CES INSTRUCTIONS
-SUITE PAGE SUIVANTE-

19
19
CONSERVER CES INSTRUCTIONS
MISE AU REBUT DU LAVE-LINGE
nL'appareil doit être débranché de sa source de courant électrique
durant les interventions de service et le remplacement des pièces.
nNe pas toucher les commandes.
nSi le cordon d'alimentation est endommagé, il doit être remplacé
par le fabricant, son technicien d'entretien ou une personne
présentant une qualication similaire pour éviter tout risque.
nLes adoucissants ou produits similaires doivent être utilisés
conformément aux instructions du fabricant de l'adoucissant.
nAVERTISSEMENT: Cet appareil ne doit pas être alimenté par le
biais d'un dispositif de commutation externe comme un minuteur,
ou branché à un circuit qui est régulièrement mis sous tension et
hors tension par un appareil.
nLes ouvertures de ventilation dans la base ne doivent pas être
obstruées par un tapis ou un objet similaire.
nLes nouveaux jeux de tuyaux fournis avec l'appareil doivent être
utilisés. Les anciens jeux de tuyaux ne doivent pas être réutilisés.
nEn cas de panne, seules les pièces de rechange autorisées doivent
être utilisées.
nVoir la section «Caractéristiques électriques» pour les instructions
de mise à la terre.
nSi le cordon d'alimentation est endommagé, il doit être remplacé
par un cordon spécial disponible auprès du fabricant ou de son
technicien d'entretien.
nToutes les opérations d'entretien et d'installation doivent être
effectuées par un technicien d'entretien Maytag, un électricien
qualié ou une personne présentant une qualication similaire.
Cet appareil est conforme à la directive européenne 2002/96/EC relative aux appareils électriques et électroniques usagés
(WEEE).
Mettre ce produit aux rebuts de la bonne façon, on s’assure de prévenir les conséquences néfastes sur l’environnement et la
santé humaine qui se produiraient si l’appareil n’est pas mis aux rebuts de façon adéquate.
Le symbole sur le produit ou sur les documents accompagnant le produit indique que cet appareil ne doit pas être considéré
comme un déchet domestique. Il doit être apporté au point de collecte applicable pour le recyclage des éléments électriques et
électroniques.
La mise aux rebuts doit s’effectuer en respectant les réglementations locales en matière d’environnement.
Pour obtenir des renseignements plus détaillés sur le traitement, la récupération et le recyclage de ce produit, contacter le
bureau local de votre ville, le service de traitement des déchets domestiques ou la boutique dans laquelle l’appareil a été acheté.

20
Pièces supplémentaires
Il se peut que l'installation nécessite des pièces supplémentaires.
Pour acheter l'un des articles indiqués ici, contacter le revendeur
agréé Maytag le plus proche.
Si vous avez Vous devrez acheter
Évier de buanderie ou
tuyau de rejet à l'égout
de plus de 2,4m (96po)
Système de pompe de puisard
(sipas déjà disponible)
Égout surélevé Évier de vidange standard de 76L
(20gallons), de 762mm (30po) de
hauteur ou évier utilitaire et pompe
de puisard (disponibles chez les
fournisseurs locaux d'articles de
plomberie)
Cordon d'alimentation amovible -
voir la section «Caractéristiques
électriques»
Égout au sol Brise-siphon, réf. 285834, tuyau
d'évacuation supplémentaire, réf.
8318155 et kit de connexion, réf.
285835
Tuyau d'évacuation trop
court Trousse de rallonge du tuyau d'évacuation de 1,2m (4 pi), réf.
DRNEXT4
Options
Piédestal
Vous pouvez acheter un piédestal séparément pour ce lave-linge.
Le piédestal augmentera la hauteur totale du lave-linge.
Piédestal facultatif
Hauteur du
piédestal Hauteur approximative avec lave-linge Couleur Référence
73mm
(27⁄8po) 1207mm (47,5po) Blanc WHP0400VW
EXIGENCES D'INSTALLATION
Outils et pièces
Rassembler les outils et composants nécessaires avant
d'entreprendre l'installation. Les pièces fournies se trouvent dans
le tambour du lave-linge.
Outils et pièces nécessaires:
Spécifications
Ces appareils sont vendus dans diverses régions du monde
ayant différents critères de capacité de mesure. Des
exemples de formes de mesures valables indiquées sur ce
produit sont présentées ci-dessous:
Capacité de linge sec: Mesure de poids qui reète un seuil
minimum pour la capacité de volume sec nécessaire à des ns
de tarifs d'importation.
Capacité IEC: Mesure de capacité qui représente la capacité
maximale de linge et de textile secs déclarée par le fabricant
comme pouvant être traitée en un cycle spécique.
Capacité de linge sec
10,5kg (23lb)
Capacité IEC
10,5kg (23lb)
Niveau sonore
LpA: 58dB(A) (KpA+/-10dB(A))
†TORX et T20 sont des marques déposées d'Acument Intellectual
Properties, LLC.
AB
DE
C
H
F
G
A. Pince ouverte à 19/16po (39mm)
B. Clé plate 1/2po (13mm)
C. Clé plate 9/16po (14mm)
D. Tournevis de sécurité TORX T20†
E. Tournevis à écrou 1/4po (6,3mm)
F. Niveau
G. Cale en bois
H. Règle ou ruban à mesurer
Pièces fournies (selon le modèle):
IJ
M
N
P
K
L
O
Q
I. Tuyau d'évacuation avec bride, forme en U
J. Attache de xation amovible
K. Tuyaux d'arrivée d'eau (2)
L. Rondelles pour tuyaux d'arrivée (4)
M. Bouchon pour les trous des boulons de transport (4)
N. Encadrement de lecteur de cartes (selon le modèle)
O. Came de blocage de porte de service (selon le
modèle)
P. Vis (selon le modèle)
Q. Cordons d'alimentation (2)