Maytag MVWC400XW4 User manual

TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
GU[DE D'UT[LISATION
ET D'ENTRETiEN DE
LA LAVEUSE HAUTE
EFFICAciT[_ A FAiBLE
CONSOMMATION D'EAU
AVEC CHARGEMENT PAR
LE DESSUS
Para una versi6n de estas instrucciones en espafiol, visite www, maytag.com
Table of Contents Table des mati6res
WASHER SAFETY ................................................................ 2
WHAT'S NEW UNDERTHE LID? ........................................ 3
CONTROL PANEL AND FEATURES ..................................... 4
CYCLE GUIDE ..................................................................... 6
USING YOUR WASHER ...................................................... 7
WASHER MAINTENANCE ................................................. 10
TROU BLESHOOTiNG ...................................................... 12
WARRANTY ...................................................................... 17
ASSISTANCE OR SERVICE ............................... BAcK cOvER
SI_CURITI _ DE LA LAvEUSE ............................................... 18
QUOI DE NEUF SOUS LE COUVERCLE? .......................... 19
TABLEAU DE COMMANDE ET
CARACTI_RiSTiQU ES ........................................................ 20
GUIDE DE PROGRAMMES ............................................... 22
UTiLISATION DE LA LAVEUSE ......................................... 24
ENTRETiEN DE LA LAVEUSE ............................................. 27
DI_PANNAGE .................................................................... 29
GARANTiE ........................................................................ 35
ASSISTANCE OU SERVICE .............. COUVERTURE ARRIERE
Designed to use only
HE High Efficiency detergents.
Consue pour ['uti[isation d'un
d6tergent haute efficacit6 seu[ement.
W10420382A
W10420383A-SP

WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injuryto persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. Ifthe hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where itwill be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user=repair instructionsthat you understand and
have the skills to carry out.
[] See "Electrical Requirements" located in the installation
instructions for grounding instructions.
this time. SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

WHAT% NEW UNDER THE LID?
Cleaning with Less Water
Traditional agitator-style
W_shQF
Washer with low-water
washplate wash system
The most striking difference in your new washer is the low-water
washp[ate wash system. The washer automatically adjusts the
water [eve[ to the load size--no water [eve[ selector is needed.
I_oad garments in loose heaps evenly around the washp[ate.
Do not load garments directly over the center of the washp[ate;
when loaded, the center of the washp[ate should be visible.
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water [eve[ for
the load. This may take several minutes before water is added. YOU
will find a step-by-step description in the "Cycle Status Lights"
section.
YOU will hear the motor turn the basket in short pulses to
thoroughly wet the load. This low-water wash method uses
less water and energy compared to a traditional agitator-style
washer.
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be
marked "HE" or "High Efficiency." I_ow-water washing creates
excessive sudsing with a regular non-HE detergent. Using regular
detergent will likely result in longer cycle times and reduced
rinsing performance. [t may also result in component failures and
noticeable mold or mildew. HE detergents are made to produce
the right amount of suds for the best performance. Follow the
manufacturer's instructions to determine the amount of detergent
to use.
U._e only High Efficiency (HE) detergent.
Concentrated Cleaning
I.ow-water cleaning means concentrated cleaning. Rather than
diluting detergent as done in an agitator-style washer, this washer
delivers the detergent directly to the soils.
Normal Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer. For
example, you may hear a clicking and hum at the beginning of
the cycle, as the lid lock goes through a serf-test. There will be
different kinds of humming and whirring sounds as the washp[ate
moves the load. And sometimes, you may hear nothing at all, as
the washer determines the correct water [eve[ for your load or
allows time for clothes to soak.
As the washer dampens and moves the load, the [eve[ of the
garments will settle in the basket. This is normal, and does not
indicate that more garments should be added.
iMPORTANT: YOU will not see a washer basket full of water as
with your past agitator-style washer. It is normal for some of the
load to be above the water line.

CONTROE PANEL AND FEATURES
O CYCLE OPTIONS
The following options may be added to most cycles.
DEEPCLEAN
This option provides enhanced cleaning action for tough
stains. [t will add additional agitation and soak time to the
cycle.
FABRIC SOFTENER ADDED
This option must be set to "Yes" if using fabric softener.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
TEMPERATURE
Temperature Control senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric and soils
being washed. For best results and following the garment [abe[
instructions, use the warmest wash water safe for your fabric.
. Warm and hot water will be cooler than what your previous
washer provided.
. Even in a cool water wash, some warm water may be added
to the washer to maintain a minimum temperature.
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See "Cycle Guide" for detailed descriptions.
OSTART/PAUSE/UNLOCK BUTTON
Pressto start the selected cycle; press again to pause the
cycle and unlock the lid. Pressand hold 3 sac to cancel a
cycle.
NOTE: If the washer is spinning, it may take several minutes
to unlock the lid. Pressand hold 3 sac to cancel a cycle.
OCYCLE STATUS LIGHTS
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses that are
different from traditional washers.
SENSING
sensing wash rinse spin done lid locked
When the START/Pause/Unlock button is pressed, the washer
will first perform a self-test on the lid lock mechanism. You
will hear a click, the basket will make a slight turn, and the
lid will unlock briefly before locking again.
Once the lid has locked the second time, the washer will
use short, slow spins to estimate the load size. These sensing
spins may take 2 to 3 minutes before water is added to the
load and you may hear the hum of these spins. [f the sensing
light is on, then washer is working properly. You will hear
the motor turn the basket in short pulses to thoroughly wet
the load. The washer will then move the load briefly, pause
to allow water to soak in to the load, and resume adding
water. This process may repeat until the correct amount of
water has been added for the load. You may also hear water
flowing through the dispenser, adding detergent to the load.
NOTE: Avoid opening lid during sensing. The sensing
process will start over when the washer is restarted. The
sensing light may also come on during the Wash portion of
the cycle. This
is normal.
WASH
sensing wash rinse spin deae lid Rac:ke_
You will hear the motor and washplate moving the load.
Unlike traditional washers, the load is not covered with
water. Low-water cleaning means concentrated cleaning.
Rather than diluting detergent as done in an agitator-style
washer, this washer delivers the detergent directly to the
soils. The motor sounds may change at different stages in
the cycle. The wash time is determined by the selected soil
level.
4

RNNSE LID LOCKED
sensingwash rinse spin done lidlocked
YOU will hear sounds similar to the wash cycle as the washer
rinses and moves the load. Fabric softener will be added if
the Fabric Softener Added-Yes option was selected. Some
cycles will use a spray rinse.
SPNN
sensingwash rinse spin done lidIncited
The washer spins the load at increasing speeds for proper
water removal, based on the selected cycle and spin speed.
DONE
sensingwash rinse spin done lid[ockod
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
sensing wash rinse spin done lid[ocked
To allow for proper load sensing and spinning, the lid
will lock and the kid kocked light will turn on. This light
indicates that the lid is locked and cannot be opened.
Ifyou need to open the lid, press
START/Pause/Unlock. The lid will unlock
once the washer movement has stopped.
This may take several minutes if the load
was spinning at high speed. PressSTART/
Pause/Unlock again to resume the cycle.
Avoid opening the lid during sensing. The
start 1
,ause/un[ock j
sensing process will start over when the washer is
restarted.

CYCLE GUIDE
For best fabric care, choose the cycle that best fits the load being washed.
Not all cycles and options are available on a[[ models.
Heavily soiled fabrics
Sturdy fabrics, colorfast
items, towels, jeans
Large items such as
sheets, small comforters,
jackets
Cottons, linens, sheets, and
mixed garment loads
Light weight cotton and
cotton blends
[Heavy Duty
Heavy
[Heavy Duty
Regular
Normal
Heavy
Normal
Regular
Normal
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
Warm
Coo[
Cold
Hot
No-iron fabrics, cottons,
perm press, synthetics
Large items such as sheets,
sleeping bags, small
comforters, jackets, and
small washable rugs
Machine-wash silks,
hand-washed fabrics
Swimsuits and items
requiring rinsing without
detergent
Dripping wet item or
hand-washed items
No clothes in washer
*All rinses are cold.
Light Warm
Cool
Cold
Casual Hot
Warm
Cool
Cold
Bulky Hot
Warm
Coo[
Cold
Delicate Hot
Warm
Coo[
Cold
Rinse & Cold
Spin
Drain& N/A
Spin
Clean Hot
Washer Warm
Coo[
Cold
**Spin speed is integrated into the cycle and can not be selected.
High
High
High
High
High
Low
High
Low
High
High
High
Provides maximum wash time and action for tough stains
and soils. Use this cycle for heavily soiled or sturdy items.
Water-level sensing process may take longer for some items
than for others because they will absorb more water than
other fabric" types.
Use this cycle for heavily soiled or sturdy items. Water-level
sensingprocess may take longer for some items than for
othersbecause they will absorb more water than other fabric
types.
Use this cycle for heavily soiled cottons and mixed fabric
loads. This cycle features a spray rinse.
Use this cycle for normally soiled cottons and mixed fabric
loads. This cycle features a spray rinse.
Use this cycle for light weight cottons that are lightly soiled.
This cycle features a spray rinse.
Use this cycle to wash loads of no-iron fabrics such as sport
shirts, blouses, casual business clothes, permanent press, and
blends.
Use this cycle to wash large items such as jackets and small
comforters. The washer will fill with enough water to wet
down the load before the wash portion of the cycle begins,
and uses a higher water [eve[ than other cycles. Do not tightly
pack basket.
Use this cycle to wash lightly soiled garments indicating
"Machine Washable Silks" or "Gentle" cycle on the care
[abe[. Place small items in mesh garment bags before
washing. This cycle uses a higher, preset water [eve[.
Combines a rinse and high speed spin for loads requiring
an additional rinse cycle or to complete a load after power
interruption. This cycle uses a higher, preset water [eve[. Also
use for loads that require rinsing only.
This cycle uses a spin to shorten drying times for heavy fabrics
or special-care items washed by hand. Use this cycle to drain
washer after cancelling a cycle or completing a cycle after a
power failure.
Use this cycle every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water [eve[.
Use with AFFRESH ®washer cleaner tablet or liquid chlorine
bleach to thoroughly clean the inside of your washer. This
cycle should notbe interrupted. See "Cleaning Your Washer."
IMPORTANT: Do not place garments or other items in the
washer during the Clean Washer cycle. Use this cycle with
an empty wash tub. J

USING YOUR WASHER
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. sortand prepare your laundry
• Empty pockets. Loose change, buttons, or any small object
can pass under the washplate and become trapped, causing
unexpected sounds.
Sort items by recommended cycle, water temperature, and
colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
• Treat stains promptJy.
• Close zippers, fasten hooks,tie strings and sashes, and remove
non-washable trim and ornaments.
Mend rips and tears to avoid further damage to items during
washing.
Helpful Tips:
When washing water-proof or water-resistant items, load
evenly. See "Cycle Guide" for tips and more information on
using the Bulky cycle.
Use mesh garment bags to help avoid tangling when washing
delicate or small items.
Turn knits inside out to avoid pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up
lint from towels, rugs, and chenille fabrics.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Add a measured amount of HE
detergent into the basket.
iMPORTANT: Use only High Efficiency detergents. The package
will be marked "HE" or "High Efficiency." Low-water washing
creates excessive sudsing with a regular non-H E detergent.
Using regular detergent will likely result in longer cycle
times and reduced rinsing performance. [t may also result in
component failures and noticeable mold or mildew. HE
detergents are made to produce the right amount of suds for the
best performance. Follow the manufacturer's instructions
to determine the amount of detergent to use.
Using Oxi or color-safe bleach:
[f using an Oxi or color-safe bleach laundry boost product, add
to the bottom of the washer basket before adding clothes.

Load garments in loose heaps evenly
around the washplate. Do not load
garments directly over the center of the
washp[ate; when loaded, the center of
the washp[ate should be visible. Try
mixing different sized garments to
reduce tangling.
IMPORTANT: Garments need to move
freely for best cleaning and to reduce wrinkling
and tangling.
to dispenser, if desired
Do not overfill, dilute, or use more than 1 cup (250 mL). Do not
use color-safe bleach or Oxi products in the same cycle with
liquid chlorine bleach.
This washer has been designed to allow
the use of the Downy Ball ® to dispense
fabric softener in the rinse cycle. Pour a
measured amount of Downy ® liquid fabric softener into the
Downy Ball ®, pull the ring tightly to seal it, and place on top
of load. Always follow manufacturer's directions for correct
amount of fabric softener based on your load size. Then select
Fabric Softener Added-Yes option. The Downy BalP will
automatically release the fabric softener during the rinse cycle.
For questions on using the Downy Ball ® call 1-800-688-7638 or
visit www.downy.com.
IMPORTANT: Fabric Softener Added option must be selected to
"Yes" to ensure proper distribution at correct time in cycle. Do
not overfill or dilute.
Adding Liquid Fabric Softener Manually to Wash Load
During the final rinse, wait until the washer has completed filling,
press the START/Pause/Unlock button to pause the washer. Lift
the lid and add the measured recommended amount of liquid
fabric softener. Do not allow liquid fabric softener to spill, splash,
drip, or run into the basket or on load. Do not use more than the
recommended amount. Close the lid and press the START/Pause/
Unlock button again to start the washer.
IMPORTANT: Fabric Softener Added option must be selected to
"Yes" to ensure proper distribution of the fabric softener during
the rinse portion of the cycle.
regular
heavy duty
heavy
delicate
Turn cycle knob to choose your wash cycle.

7. Select wash temperature
temperature
all c0[d rinses
cold
9. Press START/Pause/Unlock to begin
wash cycle
start
pause/unlock
hold3sec,
to cancel
Once you select a cycle, select the desire wash temperature by
turning the Temperature knob to the desired setting.
Always read and follow fabric care [abe[ instructions to avoid
damage to your garments.
iii.or iii
::iSome cold water is added to save Whites and pastels
::ienergy. This will be cooler than Durable garments
your hot water heater setting. , .,
:: , Heavy so s
Wa,m :::
ii
Some cold water will be added, so Bright colors
this will be cooler than what your Moderate to light soils
previous washer provided.
CooI
Warm water is added to assist in ::i Colors that bleed
soil removal and to help dissolve : or fade
detergents. Light soils
Cold
ii Warm water may be added to assist Dark colors that
:i in soil removal and to help dissolve bleed or fade
: detergents.
Press the START/Pause/Unlock button to start the wash cycle.
Filling is delayed for several minutes while load balance is
sensed. When the cycle has finished, the DONE indicator will
light. Promptly remove garments after cycle has completed
to avoid odor, reduce wrinkling, and rusting of metal hooks,
zippers, and snaps.
Unlocking the lld to add garments
If you needto open the lid to add 1 or 2 missed garments:
Press START/Pause/Unlock; the lid will unlock once the washer
movement has stopped. This may take several minutes if the
load was spinning at high speed. Then close lid and press
START/Pause/Unlock again to restart the cycle.
If lid is left open for more than 10 minutes the water will pump
out automatically.
DeLay in water fill
Filling is delayed for 2 to 3 minutes to check for load unbalance.
You will hear the hum of the spin prior to filling. This is normal
operation.
8. Select cycle options, if desired
deep dean extra rinse
off on off on
If you would like to add a Deep Clean and/or Extra Rinse
option, turn the knob for that feature to ON.

WASH ER MA[ NTENANCE
rWATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the [abe[ with a permanent marker.
f NON-USE AND VACATION CARE
operate your washer only when you are home.
If moving, or not using your washer for a period of time,
fo[ low these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes. To keep
washer interior odor-free, follow this recommended cleaning
procedure after every 30 washes:
1. Make sure the washer is empty.
2. Using liquid chlorine bleach, add 1 cup (250 mL) to
liquid chlorine bleach dispenser.
IMPORTANT: Do not add detergent to CLEAN WASHER
cycle. Do not use more than recommended amount of bleach
to avoid damaging product over time.
3. Close washer lid.
4. Select CLEAN WASHER cycle.
5. Press START/Pause/Unlock.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, press and hold START/Pause/Unlock for three
seconds and run a RINSE & SPIN cycle to ensure cleaner or
bleach have been rinsed from washer.
Cleaning the bleach dispenser
Wipe the inside of the bleach dispenser with a dean, damp
cloth.
To clean exterior:
1. Use a soft, damp cloth or sponge to wipe up any spills.
2. Use all-purpose surface cleaner, if needed.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
fwi NTER STORAG E cARE
IMPORTANT: TO avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. [f storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE& SPIN cycle for about 30 seconds to
mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
10

TRANSPORTi NG YOU RWASH ER
1. Shut off both water faucets, Disconnect and drain water
inlet hoses,
2. [f washer wiJ[ be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain from drain system and drain any
remaining water into a pan or bucket, Disconnect drain
hose from back of washer,
4. Unplug power cord,
5. Place inlet hoses and drain hose inside washer basket,
6. Drape power cord over edge and into washer basket,
7. Place packing tray from original shipping materials
back inside washer, if you do not have packing tray,
place heavy blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in new
location,
REINSTAI.MNG/USING WASHER AGAIN
To reinstall washer after non-use, vacation, winter storage, or
moving:
1. Refer to "installation instructions" to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses, Reconnect water inlet hoses,
Turn on both water faucets,
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. PJug in washer or reconnect power.
3. Run washer through BULKY cycle to clean washer and
remove antifreeze, if used. Use only HE High Efficiency
detergent. Use 1/2 the manufacturer's recommended
amount for a medium-size load.
11

TROUBLESHOOTING
f First try the solutions suggested here or visit our website to possibly avoid the cost of a service ca[[...
in U.S.A. www.maytag.com/he[p - in Canada www.maytag.ca
Check the following for
proper installation or
see "Using Your Washer"
section,
Clicking or metallic
noises
Feet may not be in contact with the
floor and locked.
Washer may not be level,
Load could be unbalanced.
Objects caught in washer
drain system,
Gurgling or humming Washer may be draining water,
Humming The sensing light is on,
....ii
Check the following for Washer not level.
proper installation:
Fill hoses not attached tightly.
Fill hose washers,
Drain hose connection,
Check household plumbing for leaks
or dogged sink or drain,
Washer not loaded as
recommended,
Not enough water Load not completely covered
in washer in water.
Front and rear feet must be in firm contact with floor, and washer
must be level to operate properly, lam nuts must be tight against
the bottom of the cabinet. See "installation instructions".
Check floor for flexing or sagging, If flooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer wi[[ reduce sound,
See "Level the Washer" in installation instructions,
Load garments in loose heaps evenly around the washplate. Do
not load garments directly over the center of the washplate.
Adding wet items to washer or adding more water to basket could
unbalance washer.
Wash smaller loads to reduce imbalance.
Do not tightly pack. Avoid washing single items.
Use Bulky cycle for oversized, non-absorbent items such as
jackets and small comforters.
See "Cycle Guide" and "Using Y0ur Washer" in this Use and
Care Guide,
Empty pockets before washing, Loose items such as coins could fall
between basket and tub or may block pump, it may be necessary to
ca[[ for service to remove items,
it is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket,
it is normal to hear the pump making a continuous humming sound
with periodic gurgling or surging as final amounts of water are
removed during the spin/drain cycles.
You may hear the hum of the sensing spins after you have started the
washer. This is normal. Sensing spins will take several minutes before
water is added to the washer.
Water may splash off basket if washer is not level,
Check that load is not unbalanced or tightly packed,
Tighten fill-hose connection,
Make sure a[[ four fi[[ hose fiat washers are properly seated,
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub,
Do not place tape over drain opening.
Water can backup out of a clogged sink or drainpipe, Check all
household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets,)
Unbalanced loading can cause basket to be out of alignment and
cause water to splash off tub. See "Using Your Washer" for loading
instructions.
This is normal operation for an HE low-water washer. The load will
not be completely under water, The washer senses load sizes and adds
correct amount of water for optimal cleaning, See "What's New under
the Lid,"
IMPOITANT: Do not add more water to washer, Adding water lifts the
garments off the washplate, resulting in less effective cleaning. .j
12

TROU BLESH OOT[ NG
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
f
if you experience
.... ,@
Washer won't run
or fill, washer stops
working or wash light
remains on dndicafing
that the washer
was unable to fill
appropriately)
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call... "_
[n U.S.A. www.maytag.com/help - [n Canada www.maytag.ca
i
Check for proper water supply, Both hoses must be attached and have water flowing to inlet valve,
Check proper electdca[ supply.
Normal washer operation.
Washer may be tightly packed.
Not using HE detergent or using too
much HE detergent.
Both hot and cold water faucets must be turned on,
Check that inlet valve screens have not become dogged,
Check for any kinks in inlet hoses, which can restrict water flow,
Plug power cord into a grounded 2, prong outlet,
Do not use an extension cord,
Ensure there is power to outlet,
Reset a tripped circuit breaker, Replace any blown fuses,
NOTE: If problems continue, contact an electrician,
Lid must be closed for washer to run,
Washer will pause during certain phases of cycle, Do not
interrupt cycle,
Washer may be stopped to reduce suds,
The washer senses the dry load with short spins that may take
2 to 2,minutes before water is added, YOu may hear the hum of
the spins, This is normal,
Remove several items, rearrange load evenly around the
washp[ate, Do not load garments directly over the center
of the washplate, (]lose lid and press START/Pause/Unlock,
Add only 1 or 2 additional garments after washer is started,
Do not add more water to the washer,
Only use HE detergent, Suds from regular detergents can slow or
stop the washer. Always measure detergent and follow
detergent directions based on your load requirements,
To remove suds, cancel cycle, Select RINSE & SPIN. Press START/
Pause/Unlock. Do not add more detergent, j
13

TROU BEESHOOT[ NG
rFirst try the solutions suggested here or visit our website to possibly avoid the cost of a service call... -_
In U.S.A. www.maytag.com!he[p - In Canada www.maytag.ca
If you experience Possible causes Solution
Washer not draining/
spinning, loads are still
wet, or spin light remains
on (indicating that the
washer was unable to
pump out water within
10 minutes)
Dry spots on load
after cycle
Incorrect or wrong wash
or rinse
temperatures
Emptypockets and usegarment bags for
small items.
Using a cycle with a low spin speed.
The washer may be tightly packed or
unbalanced.
Check plumbing for correct
drain hose installation. Drain hose
extends into standpipe farther than
4.5" (114 mm).
Too much detergent causing suds to
slow or stop draining and spinning.
High speed spins extract more
moisture than traditional top-load
washers.
Check for proper water supply.
Energy-saving controlled
wash temperatures.
Load not rinsed Check for proper water supply.
Small items may have been caught in pump or between basket
and tub, which can slow draining.
Cycles with lower spin speeds remove less water than cycles with
high spin speeds. Use the recommended cycle/speed spin for your
garment. To remove extra water in the load, select DRAIN & SPIN.
Load may need to be rearranged to allow even distribution of the
load in the basket.
Tightly packed or unbalanced loads may not allow the washer to
spin correctly, leaving the load wetter than normal. Evenly arrange
the wet load for balanced spinning. Select the Drain & Spin cycle
to remove excess water. See "Using Your Washer" for loading
recommendations.
Check drain hose for proper installation. Use drain hose form and
securely attach to drainpipe or tub. Do not tape over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Remove any clogs from drain hose.
Use only HE detergent. Always measure and follow detergent
directions for your load. To remove extra suds, select RINSE &
SPIN. Do not add detergent.
The high spin speeds combined with air flow during the final spin
can cause items near the top of the load to develop dry spots
during the final spin. This is normal.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and have
both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star¢_qualified washers use cooler wash and rinse water
temperatures than traditional top-load washer. This includes
cooler hot and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Not using HE detergent or using too The suds from regular detergent can keep washer from operating
much H E detergent, correctly.
Washer may be tightly packed.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions based
on load size and soil [eve[.
The washer is less efficient at rinsing when tightly packed.
Load garments in loose heaps evenly around the washp[ate. Do
not load garments directly over the center of the washp[ate.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 additional garments after washer is started. J
14

TROUBLESHOOTING
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call... -_
In U.S.A. www.maytag.com/help - In Canada www.maytag.ca
ff you experience Possible Causes So[ution
Add an Extra Rinse to the selected cycle.Sand, pet hair, lint, etc.
on load after washing
Load is tangling
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Washer not loaded as recommended.
Not cleaning or Wash load not completely
removing stains covered in water.
Added more water to washer.
Washer not loaded as recommended.
See "Using Your Washer" section.
Select a cycle with a slower wash action and spin speed, however
items will be wetter than those using a higher speed spin, See the
"Cycle Guide" to match your load with the best cycle,
Load garments in loose heaps evenly around the washplate, Do
not load garments directly over the center of the washplate,
Reduce tangling by mixing types of load items, Use the
recommended cycle for the type of garments being washed,
Washer senses load size and adds correct amount of water. This is
normal and necessary for clothes to move,
Do not add more water to washer, Adding water lifts the garments
off the washplate, resulting in less effective cleaning,
Washer is less efficient at cleaning when tightly packed,
Load garments in loose heaps evenly around the washplate, Do
not load garments directly over the center of the washplate,
Add only ] or 2 additional garments after washer is started,
Adding detergent on top of load. Add detergent, oxi products and color-safe bleach to the bottom of
the basket before adding the load items.
Not washing like colors together. Wash like colors together and remove promptly after the cycle is
complete to avoid dye transfer.
Not using H E detergent or using too
much HE detergent,
Not using correct cycle for fabric type.
Not using dispenser or Downy BaIP,
The suds from regular detergent can keep washer from
operating correctly,
Use only HE detergent, Be sure to measure correctly,
Always measure detergent and follow manufacturer's directions
based on load size and soil [eve[,
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning,
Use Heavy Duty Heavy and Heavy Duty Regular cycle for tough
cleaning. See the "Cycle Guide" to match your load with the best
cycle.
Use dispenser for chlorine bleach and Downy Ball °'_for fabric
softener to avoid staining.
Load dispenser before starting a cycle.
Do not add products directly onto load.
Not selecting Fabric Softener Always select "Yes" when adding fabric softener. Cycles that use
Added-Yes. spray rinsing will add additional water for proper fabric softener
dispensing when "Yes" is selected,
Incorrect dispenser Clogged dispenser. Use only liquid chlorine bleach in the bleach dispenser.
OP eration .j
15

TROUBkESHOOT[NG
First try the solutions suggested here or visit our website to possibly avoid the cost of a service call...
In U.S.A. www.maytag.com/help - In Canada www.maytag.ca
Fabric Damage
Odors
Sharp items were in pockets during
wash cycle. Empty pockets, zip zippers, and snap or hook fasteners before washing to avoid snags and tears.
Strings and straps could have tangled, Tie a[[ strings and straps before starting wash load,
Items may have been damaged before Mend rips and broken threads in seams before washing.
washing.
Fabric damage can occur if washer is
tightly packed.
Liquid chiodne bleach may have been
added incorrectly,
Garment care instructions may not have
been fol lowed.
Monthly maintenance not done as
recommended.
Using wrong or too much detergent.
Load garments in loose heaps evenly around the washplate. Do
not load garments directly over the center of the washp[ate.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 additional garments after washer is started.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach wi[[ damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when loading
and unloading washer.
Always read and follow garment manufacturer's care label
instructions. See the "Cycle Guide" to match your load with the
best cycle.
Run the (:lean Washer cycle after every 30 washes, See "(:leaning
Your Washer" in Washer Maintenance,
Unload washer as soon as cycle is complete.
Use only HE detergent, Be sure to measure correctly, Always
follow the manufacturer's directions,
See "(:leaning your Washer" section.
Lid locked light is The lid is not closed. (:lose the lid. The washer will not start or fill with the lid open.
flashing A cycle was stopped or paused The washer may still be spinning. The lid will not unlock until
using the Start/PausejUnlock button, the basket has stopped spinning. This may take several minutes if
washing large loads or heavy fabrics, j
16

MAYTAG ®LAUNDRY WARRANTY
LIMITED WARRANTY
For one year frorn the date of purchase, when this rna'orj appliance is operated and rnaintained according to instructions attached to or
furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada I_P (hereafter "Maytag") will pay for factory
specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased.
Service must be provided by a Maytag designated service company. YOUR SOLE AND EXCI_USIVE REMEDY UNDER THIS IJMITED
WARRANTY SHAI.L BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and
applies on[}/when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain
service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Rep[acernent parts or repair labor if this rnajor appliance is used for other than norrna[, sing[e-farni[y household use or when it is used in
a manner that is inconsistent to published User or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair
house fuses, or to correct house wMng or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance
with electrical or plumbing codes, or use of products not approved by Maytag.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results
from defects in materials or workmanship and is reported to Maytag within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Maytag servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
Maytag published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be
easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPI.IED WARRANTIES, INCI_UDING ANY IMPHEI) WARRANTY OF MERCHANTABII_ITY OR IMPHEI) WARRANTY OF FITNESS FOR A
PARTICUI_AR PURPOSE, ARE IJMITED TO ONE YEAR OR THE SHORTEST PERIOD AH_OWED BY I.AW. Some states and provinces do not
allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOI_E AND EXCI_USIVE REMEDY UNDER THIS I.IMITEI) WARRANTY SHAH_ BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHAH_ NOT BE I.IABI_E FOR INCIDENTAl_ OR CONSEQUENTIAl_ DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine if another warranty applies.
If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem
after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Maytag. In the
U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777. 6/08
Keep this book and your sales slip together for future reference.
You must provide proof of purchase or installation date for in-
warranty servmce.
Write down the following inforrnation about your rnajor appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
17

SECURiTE DE LA LAVEUSE
Votre s_curit_ et celle des autres est tr_s importante,
Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareil menager.
Assurez=vous de toujours lire tous les messages de securit6 et de vous y conformer.
Voici le symbole d'alerte de s6curit6.
Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de deces et de blessures graves
& vous et a d'autres.
Tousles messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de d6ces ou de blessure grave si
vous ne suivez pas imm_diatement [es instructions,
Risque possible de d_c_s ou de blessure grave
si vous ne suivez pas les instructions.
Tousles messages de s_curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de
blessure et ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE S['CURITI_
AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc electrique ou de blessures Iors de I'utilisation de la
laveuse, suivre les precautions fondamentales dont les suivantes :
[] Lire toutes les instructionsavant d'utiliser la laveuse.
[] Ne pas laver des articles qui ont et6 nettoy6s ou
lav6s avec de I'essence ou imbib6s d'essence,
solvants de nettoyage & sec, ou autres substances
inflammables ou explosives; ces substances
peuvent 6mettre des vapeurs susceptibles de
s'enflammer ou d'exploser.
[] Ne pas ajouter d'essence, solvant de nettoyage &
sec ou autre produit inflammable ou explosif dans
I'eau de lavage. Ces substances peuvent emettre
des vapeurs susceptibles de s'enfiammer ou
d'exploser.
[] Dans certaines conditions, de I'hydrog6ne gazeux
peut se former dans un circuit d'eau chaude qui n'a
pas 6t6 utilis6 pendant 2 semaines ou plus. LE GAZ
HYDROG#NE EST EXPLOSIBLE. Si le circuit d'eau
chaude n'a pas 6t6 utilis6 pendant une telle p6riode,
avant d'utiliser la laveuse, ouvrir tousles robinets
d'eau chaude et laisser I'eau s'6couler pendant
plusieurs minutes par chaque robinet. Ceci
permettra 1'6vacuation de I'hydrog6ne gazeux
accumul6. Comme ce gaz est inflammable, ne pas
fumer ou utiliser une flamme nue au cours de cette
p6riode.
[] Ne pas laisser des enfants jouer sur ou &I'interieur de la
laveuse. Bien surveiller les enfants Iorsque la laveuse est
utilisee & proximite d'enfants.
[] Avant de mettre la laveuse au rebut ou hors de service,
enlever la porte ou le couvercle.
[] Ne pas tenter d'atteindre un article & I'interieur de la cuve de
la laveuse Iorsque le tambour, la cuve ou I'agitateur est en
mouvement.
[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle
serait exposee aux intemperies.
[] Ne pas modifier les organes de commande.
[] Ne pas reparer ou remplacer un composant quelconque de
la laveuse, ni entreprendre une operation de service, si ce
n'est specifiquement recommande dans ce manuel ou darts
un manuel d'instructions de reparations destine & I'utilisateur;
il est alors essentiel que la personne concernee comprenne
ces instructions et soit competente pour les executer.
[] Pour les instructionsde liaison &la terre, voir "Specifications
electriques" dans les instructionsd'installation.
CONSERVEZ CES INSTRUCTIONS
Avertissements de la proposition 65 de I'E_tatde Californie :
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'!_tat de Californie pour 6tre & I'origine de
cancers.
AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par I'#:tat de Californie pour 6tre b,I'origine de
malformations et autres deficiences de naissance.
18

QUOM DE NEUF SOUS LE COUVERCLE?
Nettoyey avec moins d'eau
I.aveuse traditionnelle
de type agitateur
I.aveuse _1faible consommation
d'eau avec plateau de lavage
]_a nouveaut6 [a plus flagrante de cette nouvelle [aveuse est son
syst&me de [avage _ faibie consommation d'eau avec plateau
de [avage. ]_a [aveuse ajuste automatiquement [e niveau d'eau
en fonction de [a taille de [a charge - nu[ besoin de s6iecteur de
niveau d'eau.
Charger [es v6tements sans [es tasser et de fagon uniforme [e long
du plateau de [avage. Ne pas placer [es v6tements directement au
centre du plateau de [avage - ce[ui-ci dolt 6tre visible.
D tection automatique de tai[[e de charge
Une fois que I'on d6marre le programme, le couvercle se
verroui[[e et [a [aveuse entame un processus de d6tection pour
d6terminer [e niveau d'eau appropri6 _ [a charge. Ce[a peut
prendre p[usieurs minutes avant que ['eau ne soit ajout6e. Voir
[a description pas-5-pas dans [a section "T6moins [umineux de
programme".
Vous entendrez [e moteur faire tourner [e panier par de brefs
mouvements d'impu[sion pour bien imbiber [a charge. Cette
m6thode de [avage avec faib[e consommation d'eau uti[ise moins
d'eau et d'6nergie qu'une [aveuse traditionne[[e de type agitateur.
Choix du d teygent appyopyi
Uti[iser uniquement des d6tergents Haute efficacit6. L'emba[[age
portera [a mention "HE" ou "High Efficiency" (haute efficacit_4).
Un [avage avec faib[e consommation d'eau produit un exc&s
de mousse avec un d6tergent non HE ordinaire. I[ est probable
que ['uti[isation d'un d6tergent ordinaire pro[ongera [a dur6e
des programmes et r6duira [a performance de ring:age. Ceci peut
aussi entratner des d6fai[[ances des composants et une moisissure
perceptible. Les d6tergents HE sont conq:us pour produire [a
quantit6 de mousse ad6quate pour [e mei[[eur rendement. Suivre
[es recommandations du fabricant pour d6terminer [a quantit6 de
d6tergent _ utiliser.
Uti/iser uniquement un d6tergent Haute efficacit6 (HE).
Nettoyage concenty
I.e syst6me de lavage _ faible consommation d'eau signifie un
[avage concentr6. Plut6t que de diluer du d6tergent comme dans
une [aveuse de type agitateur, cette [aveuse Jib,re [e d6tergent
directement sur [es endroits souill6s.
Sons noymaux py visib[es
Au cours des diff6rents stades du programme de [avage, vous
entendrez peut-6tre des bruits que votre [aveuse pr6c6dente ne
produisait pas. Par exemp[e, vous entendrez peut-6tre un c[iquetis
au d6but du programme Iorsque le systf_me de verrouillage du
couverc[e effectue un test automatique. On entendra diff6rents
bourdonnements et bruits de frottements rythmiques _ mesure
que I'impulseur d6place la charge. Parfois, il est possible que
[a [aveuse soit comp[f_tement si[encieuse, [orsqu'e[[e d6termine
[e niveau d'eau ad6quat ou qu'e[[e [aisse tremper [es v6tements.
mesure que [a [aveuse imbibe et d6place [a charge, [es
v6tements se tassent dans [e panier. Ceci est normal et ne
signifie pas que ['on doive rajouter des v6tements.
IMPORTANT : I_epanier de la laveuse ne sera pas rempli d'eau,
comme avec votre pr6c6dente [aveuse de type agitateur. I[ est
normal qu'une partie de la charge d6passe du niveau d'eau.
19

TABLEAU DE COMMANDE ET CARACT R[ST[QUES
A
U OPTIONS DE PROGRAMMES
[[ est possible d'ajouter [es options suivantes _ [a p[upart des
programmes.
DEEP CLEAN (nettoyage en profondeur)
Cette option fournit une action de nettoyage amGlior(_e pour
[es taches tenaces. Ceci pro[onge [a durGe d'agitation et de
trempage du programme.
FABRIC SOFTENERADDED
(a]out d'assoup[ksant pour tksu)
Le "Yes" de cette option doit _tre sG[ectionn6 si ['on uti[ise
de ['assoup[issant pour t[ssu.
EXTRA RINSE (rinsage suppl_mentaire)
On peut utiliser cette option pour ajouter automatiquement
un second rin_age _ [a plupart des programmes.
O TEMPI_RATURE
La fonction de contrG[e de tempGrature dGtecte et maintient
une tempGrature uniforme de ['eau en rGgu[ant [e dGbit
d'arrivGe d'eau chaude et d'eau froide.
SGlectionner une tempGrature de [avage en fonction du type
de tissu et de salet6 _ laver. Pour des rGsultats optimaux,
suivre les instructions sur 1'Gtiquette du vGtement et utiliser la
tempGrature d'eau de lavage [a plus chaude possible qui reste
sans danger pour le tissu.
• Les tempGratures de I'eau tilde et de I'eau chaude seront
infGrieures _ celles de votre prGcGdente laveuse.
• MGme avec un lavage _ I'eau froide, il est possible que de
I'eau tilde soit ajoutGe _ la laveuse pour maintenir une
tempGrature minimale.
OBOUTON DE PROGRAMME DE LAVAGE
Utiliser [e bouton de programme de lavage pour s6lectionner
les programmes disponibles sur la laveuse. Tourner le bouton
de programme pour s6lectionner un programme correspondant
la charge de linge. Voir "Guide de programmes" pour des
descriptions d(_tailI(_es.
O
O
BOUTON START/PAUSE/UNLOCK
(rake en marche/pause/d_verrouillage)
Appuyer sur ce bouton pour dGmarrer [e programme
sG[ectionnG, puis appuyer de nouveau pour suspendre
[e programme et dGverroui[[er [e couverc[e. Appuyer pendant
3 secondes pour annu[er un programme.
REMARQUE : Si [a [aveuse tourne, [ecouverc[e peut mettre
que[ques minutes _ se dGverroui[[er.
TI_MOINS LUMINEUX DES PROGI_AMMES
Les te_moins lumineux indiquent [a progression du
programme. ,_ chaque 6tape du processus, il est possible
que I'on remarque des pauses ou des sons diff6rents de
ceux des [aveuses ordinaires.
SENSING (DI_TECTION)
sensing wash rinse spin done lid i0cked
Lorsqu'on appuie sur le bouton START/Pause/Unlock (mise
en marche/pause/dd_verrouillage), la laveuse effectue un test
automatique sur le mGcanisme de verrouillage du couvercle.
On entend un d6clic, le panier effectue un I6ger tour, et le
couvercle se d6verrouille bri_vement avant de se verrouiller
nouveau.
Une fois le couvercle verrouill6 pour la deuxi_me fois,
[a [aveuse uti[ise des essorages [ents et courts pour estimer
[e volume de [a charge. Ces essorages de dGtection peuvent
prendre 2 _ 3 minutes avant que de ['eau ne soit ajoutde _ [a
charge et[es essorages peuvent 6mettre un bourdonnement.
Si [e tdmoin [umineux de dGtection est a[[um6, ce[a signifie
que [a [aveuse fonctionne correctement. On entend
[e moteur qui fait tourner [e panier par de de courtes
impulsions pour moui[[er ['intGgra[it6 de [a charge. La
[aveuse dGp[ace ensuite bri_vement [a charge, fait une pause
pour permettre _ ['eau de tremper [a charge, et continue
ajouter de ['eau. Ce processus peut se rGpGter jusqu'_ ce
que [a quantit6 d'eau correcte ait 6t6 ajoutde _ [a charge. I[
est aussi possible que ['on entende de ['eau cou[er dans [e
distributeur, ajoutant [e dGtergent _ [a charge.
REMARQUE : Eviter d'ouvrir [e couverc[e durant [a
dGtection. Le processus de dGtection recommencera une
fois [a [aveuse remise en marche. Le tdmoin de dGtection
peut 6ga[ement s'a[[umer [ors de ['Grape de [avage du
programme. Ceci est normal.
2O