MAZE COTSWOLD User manual

Assembly Instructions for the Dining Table
IMPORTANT-RETAIN FOR FUTURE REFERENCE
COTSWOLD 8 SEAT ROUND DINING SET

Assembly Instructions
IMPORTANT- RETAIN FOR FUTURE REFERENCE
GENERAL INFORMATION
- For domestic and outdoor use only.
- We suggest you retain these instructions for future reference.
- Keep fittings out of children’s reach and keep children well away from construction area.
- Periodically check all fittings and re-tighten as necessary.
- Do not sit or stand on your table.
- Do not stand on your chair, sofa or stool.
- This product should only be used on firm, level ground. Make sure the legs remain in contact with the ground.
- Ensure any safety locks are correctly located and locked in place for any mechanisms before use.
- Keep hands away from folding mechanisms to prevent possible entrapment or injury.
- Any folding mechanisms should only be used by competent adults.
- The glass used in this product is toughened and complies with BS EN 12150-1:2009
WARNINGS
- We suggest you spend a short time reading through this leaflet
before you start.
- When you are ready to start, make sure that you have the right
tools and plenty of space.
- Unwrap all packaging materials and place the components on
a clean surface to protect it from damage. We recommend that
the packaging is used to protect the surfaces during assembly.
- Carefully check that you have all the parts before starting
assembly.
- Please retain the assembly tools. You will need them in the
future to re-tighten the bolts, or if you want to dismantle the
furniture for storage.
- Please make sure that the product is clean and dry before
putting it into storage.
- We recommend the use of furniture covers to protect your
furniture when not in use. During severe weather conditions,
please move your furniture inside. (eg. High Winds)
- To clean your items, please use mild detergent in warm water.
Rinse with clean water and dry thoroughly. Do not use abrasive
cleaners, strong detergents, bleach, acid or solvents on the
frame parts.
- When cleaning glass panels, use a damp cloth with washing up
liquid or soft soap if necessary. Do not use washing powders or
any other substances containing abrasives since these
substances can scratch glass panels.
DO’S
- Do not stand on your chairs, sofas or stools.
- Do not sit on the arms of your chair or sofa.
- When moving furniture never drag the pieces
across the floor, as this will cause damage to the joints.
- Do not use silicone based furniture polish.
- If the glass is chipped or broken, stop using the product and
consult our customer service team.
- Do not place very hot or very cold items on the glass surface,
unless adequately thick table mats are used to prevent such
items from coming into contact with the glass.
- Do not use glass as a chopping surface.
- Do not strike the glass with hard or pointed items.
DON’TS
ASSEMBLY
Two persons to assemble the unit and lift the unit
into position.
MISSING PARTS
If you are missing any fixtures or fittings for your product
please contact our customer service team.

Fixtures and Fittings
IMPORTANT-RETAIN FOR FUTURE REFERENCE
COTSWOLD 8 SEAT ROUND DINING SET
4
3
5
6
2
1
Components supplied. Please use this
guide if you require replacement parts.
46X76cm
Ref Dimensions Visual Qty
1
2
1
4
1
2
1
6
3
572X87cm
1
2
ø
58.4x0.5cm
ø
60x1.5cm
ø
149x0.8cm
ø
151x4.5cm
ø4X66mm
A
B
C
D
ø
ø
mm 605040302010
QtyDimensions
Ref
13x5mm 12
M6x20mm
1
12
12
16x1mm
Fixtures and fittings supplied(actual size)

Assembly Instructions for Dining Table
IMPORTANT-RETAIN FOR FUTURE REFERENCE
COTSWOLD 8 SEAT ROUND DINING SET
1Unbox your dining table to begin the assembly process.
Lay the table top (4) upside down on a flat surface.
2
3Turn your table over and now place your glass (3) onto
your table top.
We recommend placing your glass on top using two
persons for safety.
5
A
D
B
4
C
ø16 X1.0mm
xø4 66 mm
CX1
BX4
M6 X20mm
DX4
AX4ø13 X5.0mm Using your 2x leg side panels (5) align them
up with the screw holes.
Use a washer, bolt and nut to secure the
panels to the table top. Tighten the bolts
using the allen key. (Do not fully tighten until
you have completed the next step)
ø16 X1.0mm
xø4 66 mm
CX1
BX8
M6 X20mm
DX8
AX8ø13 X5.0mm
Now secure your other 2x other side panels (6) to the
leg side panels you have just attached.
Use a washer, bolt and nut to secure the panels to
the leg side panels.
6
B
D
A
Tighten the bolts using the allen key.
You can now fully tighten all the bolts and nuts
to make sure the panels are secure and stable.
4
3
1
2
3
4You are now ready to add the finishing touch which
is your rattan lazy susan. Place your rattan lazy susan (2)
on first and then top the lazy susan with the lazy susan
glass (1).