MAZE PERGOLAS User manual

Assembly Instructions for Pergolas (3x3m, 3x4m, 4x4m)
PERGOLAS
IMPORTANT - RETAIN FOR FUTURE REFERENCE

2
Front and rear
beams
Column
Beam (left)
Part
Description Drawing
Part
No. QTY
Beam (right)
Middle beam
Slat
Column bottom
plate
Column cover
plate
Connectors for
middle beams
Hinge ring
Hand crank
4
1
1
2
1
3x3=44
3x4=60
4x4=60
4
4
2
2
2
A1 /
A2
B1
B2
C
E
F
G
H
I
J
D
PERGOLA SPARE PARTS LIST

3
Countersunk
head screw
Pan head
screw
Flat washer
Screw and nut
- Wood-working
screw
- Rawlplug
- Flat washer
Plastic jam
40+2
20+2
8+2
2
16
1
3x3=88
3x4=120
4x4=120
M6x16
M6x16
D6x12
M4x25
M8x80
8
10x50
1
Remote control
K1
K2
K3
K4
L
M
N
P
Silicone glue
PERGOLA SPARE PARTS LIST
Part
Description Drawing
Part
No. QTY

4
Assembly instructions
Pergola
1. Install the bottom plate F on the column A,
and tighten the screw K1; complete 4 sets in sequence.
K1 QTY: 16PCS F QTY:4PCS

5
Assembly instructions
Pergola
2. Match the connector H with one side of middle beam D,
then tighten the screw K1; then complete the other side.
K1 QTY:8PCS QTY:2PCS
H

6
Assembly instructions
Pergola
3. On the floor, place the columns and beam as shown in the figure,
and note that the drain port of the column faces the same side;
Drain port
Drain port
Drain port
Drain port
A1
A2
A1
A2

7
Assembly instructions
Pergola
4. Connect B1 / B2
with the columns,
respectively, using
screws K1 to
fasten together.
Tighten screws
fully.
K1
K1
B1
4a 4b
B1
QTY:8PCS

8
Assembly instructions
Pergola
5a. Carefully erect beam B1 (with connected columns) and hold beam C in place.
5b. Carefully erect beam B2 (with connected columns) and connect to beam C.
5c. Insert and slightly tighten screws K1 (finger tight) to secure beam C to both columns
(do not over tighten screws until all columns and beams are in place)
K2
B1
QTY:4PCS

9
Assembly instructions
Pergola
6a. Raise beam C and connect to the two remaining columns.
6b. Insert and tighten screws K1 to secure beam C to both columns
6c. Secure and tighten all screws to secure all beams to
columns, securing the structure in place.
6d. Tightly secure all screws at the top of
each columns (A1 / A2)
Step 6d
K2 QTY:8PCS

10
Assembly instructions
Pergola
7.The 4 column cover plates G
are respectively mounted on
the corner connectors of the
column and the beam,
and the screws K2
are tightened in turn;
K2 QTY:12PCS QTY:4PCS G

11
Assembly instructions
Pergola
8a. Connect the sub end of the light bar
on beam B2 with the female end of the
light bar on the beam C - tighten the
cap. Repeat for other 2 corners - expect
corner with the power supply.
Female end Sub end
Connect convex of female end
with concave of sub end
with concave of sub end
Sub end Female end
8a.
8c.
8b.
8b.
Ensure power supply output is connect as
shown on the left with the ‘T’ shaped controller
connected to the power supply. Connect sub
end on beam B1 with the female end of the
controller. Tighten screw cap. Connect the
female end of beam C with the sub end of the
controller. Tighten screw cap.
Connect convex of female end
B1 C
8c. Fix the power supply on the
beam C with screws K7. Adjust the
LEDs with the remote control
QTY: 1PCSP K7 QTY: 2PCS

12
Assembly instructions
Pergola
9. Use the silicone glue (M) on the joints of the beams and columns.
MQTY: 1PCS

13
Assembly instructions
Pergola
10. Adjust the position of the four columns so that they are perpendicular to the ground.
Meanwhile, the width of the top of each two columns should be measured
in accordance with the width of the bottom of each two columns.
Then use a market pen to mark 16 holes on the ground,
which should be corresponding to the holes in the bottom plate.
Mark the location of the hole
on the ground with
a marker pen
Use tools: marker pen
(self-provided, not supplied)

14
Assembly instructions
Pergola
11. Remove the product from the mark and drill holes of
at 16 mark positions on the ground with a percussion drill.
Use Tools: Percussion Drill
(not provided)
Use Tool: Percussion Bit
(Self-provided by Installation workers)
10x80
Drilling depth
Drilling quantity 16pcs
10x80
10

15
Assembly instructions
Pergola
12. Place the plastic expansion pipe in the bottom hole of the column;
then move the product back to the hole drilled, align holes of the
column bottom plates with the hole drilled on the ground;
then set L1 into the woodworking screw L,
and fix it with the ground separately.
LQTY: 16PCS

16
Assembly instructions
Pergola
13a. Place the middle beam D between the front and rear beams C, ensuring the
slat brackets are facing the same direction as the slat brackets on beams B1 and B2.
13b. Fix washer K3 with screw K2
and align with hole below beam
D. Do not overtighten screws K2
(this is completed once all slats
are fitted).
13c. Fix washer K3 with screw K2 and
align with hole on top beam D. Do not
overtighten screws K2 (this is completed
once all slats are fitted).
K2 QTY: 8PCS K3 QTY: 8PCS

17
Assembly instructions
Pergola
3. Put two hinge rings (part I) into the gearbox drive shaft on the beam D,
fix the screw + nut K4
QTY:2PCS QTY:2 SETS
IK4 M4 M4x25

18
Assembly instructions
Pergola
15. Insert first slat (E) at
gear box side, between
the central column D and
B1 / B2. Press down on
the slat as shown below,
gently tapping with a
rubber/plastic mallet.
Secure in place with the
plastic jams (N). Tilt the
slats to 45° for second
slat and secure in place.

Assembly instructions
Pergola
18. Continue to add slat (E), along with the plastic jams (N) until all slats are fitted.
18a. The following image shows how to
insert plastic jam into foremost slat.
18b. Turn the slat to half position, insert the plastic jam N into
hole of two ends of each slat in turn.

20
Assembly instructions
Pergola
19. Put the hand crank J on, turn to open/close the slats.