MB QUART FW1-254 Instruction Manual

Sealed enclosures offer a range of performance
proles depending on the internal air volume.
Larger enclosures will have a smoother more
extended response while a small enclosure
will have increased output in a more focused
frequency range. Sealed enclosures are the
simplest to construct but do require that the box
be completely air tight.
• Use 3/4” MDF
• Make sure the woofer mounting panel is
full width and height
• Glue all mating surfaces
• Use wood screws
• Use silicone caulk on all internal joints
The internal volume of the
enclosure must be determined
to insure proper performance.
Simply measure height, width and
depth of enclosure you intend
to build. Subtract the material
thickness. Multiply these numbers
and divide by 1728 to get the
volume in cubic feet.
For enclosures with an angled
panel, measure the larger and
smaller depths, add these
together and divide by two. Use
this averaged depth.
Enclosure
Volume
D
H x W x D
1728
D1 + D2
2
Sealed
Enclosure types
Volume calculation
Subwoofer dimensions
CAUTION
Always consider consulting a professional audio installer
before installing new subwoofers. High power audio
systems have the ability create sound levels above 130dB.
Extended exposure to high sound pressure levels can
cause hearing damage.
Always run any new wiring through safe areas that wont
interfere with the normal operation of the vehicle.
Congratulations on your choice of a MB Quart subwoofer.
This “Quick Start Installation” guide is meant to help you
“hook up” and play music. For more detailed information
on system setting, speaker and subwoofer conguration,
and full specications by model, visit the website at
MBQuart.com
It’s a good idea to conrm that you have purchased the
correct size subwoofers to t your vehicle. If you have any
reservations about being able to complete the installation
yourself, we recommend contacting a professional. Be careful
as you go. Always disconnect the negative battery terminal
before starting any electrical work on the vehicle.
FW1-254 FW1-304
Height 13.5” 13.5”
Width 13.5” 13.5”
Depth 10.5” 13.5”
Vb 0.70 ft30.91 ft3
F3 52.33 48.23
Qtc 1.006 1.151
Before you start
Sealed
Recommended enclosures
Enclosure construction
in(cm) A B C D
FW1-254 10.09”(25.6) 4.94”(12.54) 9.1”(23.1) 5.6”(14.4)
FW1-304 12.19”(30.9) 5.59”(13.53) 11.00”(28) 6.3”(16)
A
B
D
C
Vented
Vented designs are NOT recommended. This
subwoofer is designed to perform in small
sealed enclosures.

MB Quart products are designed and engineered in the USA by
www.maxxsonics.com
Quick Start
Installation Guide
WARRANTY
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
defects in material and workmanship for a period of one (1) year from the date of purchase.
Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
MBQ FW1 wfr QSG 01 - rev2
A Low pass lter will allow only
the bass frequencies to reach the
woofer making for a more natural
transition to the higher frequency
drivers. Check your amplier’s
manual for details.
We recommend using an
electronic subsonic lter. This will
help to protect the woofer from
extreme low frequency distortion.
Many ampliers are equipped
with this type lter. Check your
amplier’s manual for details.
This subwoofer is equipped with
push and insert type terminals.
Strip back 1/2” wire insulation.
Push down on the terminal, then
insert the wire and release.
Depending on the number of woofers you intend to use,
you can congure the wiring to provide the best impedance
load for your system. Below are some examples. Consult
your amplier’s manual for recommendations.
Low Pass (LPF)
Subsonic
Congurations
Connections
Subwoofer specicationsCrossovers
Wiring
4 4
8
2 2
4
4 4
2
4
4 4
4 4
2.7
4 4
4 4
4 4
4 4
4 4
4 4
4 4
2
2 2
4
2 2
4
2 2
1
4
4 4
4 4
1.4
2 2
2 2
2 2
2 2
1
2
2
2
2
2
2
4 4
8
2 2
4
4 4
2
4
4 4
4 4
2.7
4 4
4 4
4 4
4 4
4 4
4 4
4 4
2
2 2
4
2 2
4
2 2
1
4
4 4
4 4
1.4
2 2
2 2
2 2
2 2
1
2
2
2
2
2
2
4 4
8
2 2
4
4 4
2
4
4 4
4 4
2.7
4 4
4 4
4 4
4 4
4 4
4 4
4 4
2
2 2
4
2 2
4
2 2
1
4
4 4
4 4
1.4
2 2
2 2
2 2
2 2
1
2
2
2
2
2
2
4 4
8
2 2
4
4 4
2
4
4 4
4 4
2.7
4 4
4 4
4 4
4 4
4 4
4 4
4 4
2
2 2
4
2 2
4
2 2
1
4
4 4
4 4
1.4
2 2
2 2
2 2
2 2
1
2
2
2
2
2
2
35 250Hz
LPF
15 35Hz
SUBSONIC
35 250Hz
LPF
15 35Hz
SUBSONIC
10Hz 100Hz 1000Hz
10Hz 100Hz 1000Hz
10Hz 100Hz 1000Hz
10Hz 100Hz 1000Hz
FW1-254 FW1-304
NomZ 2 x 4 2 x 4 Ohm
Sd 34.636 51.071 sq.cm
Revc 3.400 3.400 Ohm
BL 7.563 9.482 TxM
Vas 27.138 60.935 Liters
Cms 159.304 164.524 mm/N
Mms 84.857 143.584 Grams
Fo 43.288 32.745 Hz
Qms 7.518 4.318
Qes 1.372 1.117
Qts 1.160 0.888
no 0.155 0.185 %
SPL@1W 83.9 84.7 dB
RMS 300 400 Watts
Peak 600 800 Watts
F W 1- 2 5 4
F W 1- 3 0 4