MD SPORTS 39004 User manual

MODEL/MODELO: 39004
Please contact us before returning the product to the store.
Toll Free: 877-852-8164
Por favor póngase en contacto con nosotros antes de
devolver el producto a la tienda.
Número telefónico gratis: 877-852-8164
INSTRUCCIONES DE ARMADO

LIMITED 90 DAYS WARRANTY
1
This product is covered by a limited warranty that is effective for 90 days
from the date of purchase. The warranty covers any defects in parts and
workmanship.
This Limited Warranty gives you specific legal rights and you may also have
other rights which very from one state (province) to another.
If, during the limited warranty period, a part is found to be defective or
breaks, we will offer replacement part at no cost to you, the customer. The
only exceptions to the warranty include main frames, tabletops, playing
surfaces, batteries or tools.
The above warranty will not apply in cases of damages due to improper
usage, alteration, misuse, abuse, accidental damage or neglect.
Attention: Since you build all tables upside down, please inspect table tops
and playing surfaces right away before putting together.
“PLEASE SAVE THESE INSTRUCTIONS
AND PURCHASE RECEIPT!”
A PURCHASE RECEIPT (or other proof of purchase date) will be required
before any warranty service is initiated. All requests for warranty service can
be submitted by email, in writing or by contacting our Consumer service
Department at:
TOLL FREE: 877-852-8164
WEBSITE: www.medalsports.com.tw
*Please do not call our 800 NUMBER as well as email us. This will result in
duplicate orders and charges will occur.
*Please note that all damaged table tops need to be returned to the store.
We do not replace any tabletops or playing surfaces.
PLEASE CONTACT US BEFORE RETURNING THE
PRODUCT TO THE STORE. THANK YOU VERY MUCH!

Phillips Screwdriver – Not Included
Standard (Flat Head Screwdriver) – Not Included
Allen Wrench - Included
TOOLS REQUIRED:
ASSEMBLY TIPS:
:

!



!
2
IMPORTANT NOTICE! Please contact us before returning the product to the store.
Please read the instructions carefully, and follow all assembly, operation or safety instructions
properly in order to avoid damage or injury. For the assembly, at least two adults are required.
Some figures or drawings may not look exactly like your product. Please read and understand
the text before beginning each assembly step.
1 -
2 -
Please Keep Your Instructions! Your Model number is necessary should you need to contact
us. Please read through this instruction manual book to familiarize yourself with all parts and
assembly steps. Kindly refer to the parts identifier below and be sure that all parts have been
included.
Although we are dedicated to giving our customers the best product possible, a question may
arise or parts may be missing. If you are missing parts, or, if you have any questions, please
contact our fast and friendly service centre on:
1 - This product is intended for INDOOR use only.
2 - Please Do Not sit, climb or lean on the game table.
3 - Please Do Not drag the table when moving it in order to avoid the damaged on the legs.
4 - Please only use spray furniture polish to clean the exterior surfaces on the game table.
5 - This is not a child's toy, adult supervision is required for children playing this game.
877-852-8164
Power Tools
- Set Low Torgue
High Torque
over tightened
High Torque
over tightened
CAUTION !
Electric Screwdrivers may be helpful during
assembly; however, please set a low torque
and use extreme caution.

3
39004 PARTS LIST
Main Cabinet
1 Piece
Side Apron
2 Pieces
End Apron
2 Pieces
Leg - A
4 Pieces
Leg - B
4 Pieces
Leg Base
4 Pieces
Leg Support
4 Pieces
F4 x 1”
Flat Head Screw
16 Pieces
F4 x 1-3/4”
Flat Head Screw
12 Pieces
Billiard Ball
1 Set
Triangle
1 Piece
Wood Brace
4 Pieces
1/4” x 3/4”
Butterfly Bolt
12 Pieces
5/16” x 1-1/2” Hex Bolt
28 Pieces
5/16” Washer
28 Pieces
T4 x 1/2” Screw
16 Pieces
WP4 x 1-1/2” Screw
8 Pieces
Table Tennis Support
1 Piece
Cue
2 Pieces
Brush
1 Piece
Chalk
2 Pieces
Table Tennis Post
2 Pieces
Table Tennis Paddle
2 Pieces
Table Tennis Net
1 Piece
Table Tennis Ball
2 Pieces
Table Tennis Surface - A
2 Pieces
Table Tennis Surface - B
1 Piece
EVA Pad
12 Pieces
Leg Leveler
4 Pieces
Apron Corner
4 Pieces
Wrench
1 Piece
12345
6 7 8 9 10
11 12 13 14 15
16 17 18 19 20
21 22 23 24 25
26 27 28 29 30
31 32 33 34
Plastic Side Pocket
2 Pieces
Nut
12 Pieces
T - Nut
8 Pieces
Plastic Coner Pocket
4 Pieces
35
Pre-installed
Pre-installed
Pre-installed Pre-installed

4
FIG.1
ASSEMBLY INSTRUCTIONS
FIG. 1
12
6
11
5
4
1. Find a clean, level place to begin the assembly of your Billiard Table. The table will be assembled upside down
and then turned over on its legs once the assembly completed. This game table is heavy, and turning it over will
require at least four strong adults.
2. Remove all the parts from the box and verify that you have all of the listed parts as shown on the parts list below.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
3. Attach the Wood Brace (#13) to the Leg - B (#5) using two Screws (#16) per Brace. See FIG.1.
4. Attach the Leg - A (#4) to the Leg - B (#5) using four Screws (#11) per Leg. See FIG.1.
16 33
13
5
33
5. Attach the Leg Base (#6) to the Leg (pre-assembled) using
three Screws (#12) per Leg Base. See FIG.2.
6. Repeat the steps above for the other legs.
FIG. 2
FIG.2

5
FIG.3
FIG. 3
18
7
7. Attach the Leg Support (#7) to the Leg (pre-assembled) using
three Bolts (#18) and three Washers (#19) per Leg. See FIG.3.
8. Repeat the steps above for the other legs.
NOTE: Please make sure that all connections are tight.
FIG.4
9. Attach the Apron Corner (#31) to the End Apron (#3) using two Screws (#15) per Apron Corner. See FIG.4.
10. Repeat the steps above for the other apron corners.
3
15
31
31
8
FIG. 4
19

FIG. 5
14
2
1
6
FIG.5
11. Attach the Side Apron (#2) to the Main Cabinet (#1) using four Butterfly Bolts (#14) per Side Apron. See
FIG.5.
FIG.6
FIG.6
12. Attach the End Apron (#3) with Apron Corner (#31) to the Main Cabinet (#1) using two Butterfly Bolts (#14)
and four Screws (#15) per side. See FIG.6.
3
15
14
31
31
8

7
FIG.7
FIG.7
13. Attach the Leg Support with Leg to the Main Cabinet (#1) using four Bolts (#18) and four Washers (#19) per
Leg. See FIG.7.
14. Screw the Leg Leveler (#30) into the Leg.
18
19
30

FIG.8
8
HOLD TABLE
CABINET DO NOT
HOLD THE
LEGS
DO NOT LEAN THE
TABLE ON ITS LEGS!
CAUTION: Four strong adults are recommended to turn the table over as shown.
1. Lift the table off the ground.
2. Turn the table over.
3. Place it on all four feet at the same time on the ground.
15. Lift the table assembly from the floor with four strong adults, turn it over, and set table on its legs in the location
where you play. Go back and make sure that all connections are tight.
16. Tear off the backside paper of the EVA Pad (#29) and stick them at the bottom of the Table Tennis Surface - A
and B (#9 and #10). See FIG.8A.
29
29
9
9
9
10
FIG.8
FIG.8A
34
35

9
910
27
25
25
17
FIG.9
9
17. Place the Table Tennis Surfaces (#9 and #10) onto the billiard surface using Table Tennis Support (#17) and
insert the Net Posts (#25) and Net (#27). See FIG.9.
FIG.9
NOW YOU ARE READY TO PLAY!