MD SPORTS Menards YUS916 067M User manual

Assembly Instructions
MODEL
YUS916_067M
Menards
www.medalsports.com877-472-4296

This product is intended for INDOOR use only.
Adult supervision is required for children playing this game.
1.
2.
- Not Included
- Not Included
RECOMMENDED
Power Tools: Set to Low Torque
High Torque: Over Tightened
IMPORTANT NOTICE!
Adult Assembly Required.
CHOKING HAZARD - This item contains small parts. Not suitable for children under 3 years.
WARNING
Do not use or keep
product outdoors. For
indoor use only. No
wet/humid conditions.
Keep away from pets in
assembly area
No children in assembly
area
Phillips Screwdriver
Standard (Flat Head Screwdriver)
Electric Screwdrivers may be helpful during assembly; however, please set a low torque and
use extreme caution.
English
TOOLS REQUIRED
YUS916_067M 1(Continued on the next page.) www.medalsports.com

Electronic Scorer with Belt
5
x1
FOR FIG. 5
Platform Lock
2
x2
FOR FIG. 1
FOR FIG. 6
Pole with Hanger
3
x2
FOR FIG. 3
Hanger Hook
4
x2
FOR FIG. 3
Platform
1
x1
FOR FIG. 1
PART NUMBER FIG NUMBER
QUANTITY
PART
PART NAME
English
PARTS IDENTIFIER
YUS916_067M 2(Continued on the next page.) www.medalsports.com
Find a clean, level place to begin the assembly of your product.
Verify that you have all listed parts as shown on the part list pages.
1.
2.
BEFORE ASSEMBLY
P1
x1
Speed Bag
PRE-INSTALLED PARTS
A1
x4
4X10mm Bolt
HARDWARE
FOR FIG. 1 FOR FIG. 3
A2
x2
4X12mm Screw

ASSEMBLY
YUS916_067M www.medalsports.com3(Continued on the next page.)
English
FIG. 1
x1
1
x2
2
x4
A1
FIG. 2
1
2
Note: Open the bottom clip on
the Lock. Repeat for both Platform
Locks.
FIG. 3
x2
3
x2
4
x2
A2
A2
3
4
3
4
3
4
2
A1
A1
1
2
BOTTOM VIEW

ASSEMBLY
YUS916_067M www.medalsports.com4(Continued on the next page.)
English
FIG. 4
Note: Close the bottom clip
on the Lock.
2
FIG. 5
x1
5
SIDE VIEW
Note: Press in the push pins and
insert pole into the Electronic
Scorer.
Press
3
3
5
5
Note: Slide FIG 3 Assembly through
the Platform Lock on FIG 2 Assembly.
FIG. 3 Assembly
FIG. 2 Assembly

ASSEMBLY
YUS916_067M www.medalsports.com5(Continued on the next page.)
English
FIG. 6
x1
P1
Inflation using an air pump must be performed by an adult.
Do not use a high pressure pump to inflate the
target such as air pump for car tire.
The maximum air pressure for the Inflatable Target is 1.8 kPa.
Check before each use and at regular intervals.
●
●
●
●
WARNING
DO NOT OVER INFLATE
CLOSE
Diameter MAX:
8 inch
P1
INFLATE
P1

ASSEMBLY
YUS916_067M www.medalsports.com6(Continued on the next page.)
English
FIG. 7
Note: Make sure the Suction Cups
on the back of the Electronic Scorer
are up against the door.
BACK VIEW
Suction Cups
5
FRONT OF THE DOOR
Note: Hang the unit on the door.
BACK OF THE DOOR
Note: Buckle the Safety Strap.

ADJUST THE HEIGHT
YUS916_067M www.medalsports.com7(Continued on the next page.)
English
Note: Open the bottom clip on both
Locks. Then slide the platform up or
down, depending on the desired height.
Note: Close the bottom clips
on the Locks.
2
2

Note: If there is no operation in 5 minutes, the machine will power off automatically.
GAME DESCRIPTIONS
Press “ ” to start the machine, the default display time is 30 seconds.
Press “ ” to select game time: 30 seconds or 1 minute.
Press “ ” again to start the game. The color of the flashing light is relevant to the times of triggering per second.
A. If it’s one time per second, the light is green.
B. If it’s 2-3 times per second, the light is yellow.
C. If it’s more than 4 times per second, the light is red.
Note: After the game is over, the screen will display the total flashing time of the red light.
The language (English and French) can be switched by pressing “ ” and “ ” simultaneously for 2 seconds.
The sound can be turned off by pressing “ ” for 2 seconds. Press “ ”shortly can go back to initial status.
1.
2.
3.
4
BATTERY INSTALLATION
ELECTRONIC SCORER OPERATION
YUS916_067M www.medalsports.com8(Continued on the next page.)
English
Requires 2x1.5V AAA batteries (not included).
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
1.
2.
3.
WARNING
Battery Box: Unscrew the bolt using a screwdriver and open the battery box. Insert 2x1.5V AAA batteries ( not included)
in the sequence of polarity as shown on the inside cover. Then close the cover using a screwdriver.
The batteries must be installed according to their correct polarization (+ and -).
Please clean the battery contacts and also those of the device prior to battery installation.
If the game will not be used for a long period of time, we recommend removing the batteries.
a.
b.
c.
REMINDING:

English
DISCLAIMER
YUS916_067M 9(The last page) www.medalsports.com
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
This device complies with the Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference; and (2) This device must accept any interference received,
including interference that may cause undesired operation.
For additional resources, please contact Medal Sports Corp.
1300 Melissa Drive, Suite 124, Bentonville, AR 72712
Toll Free: 877-472-4296
NOTE
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
•
•
•