MEAZOR 3D M0102-U User manual

Multifunctional Laser Measure
USER MANUAL
Model : M0102-U / M0102
The MEAZOR 3D is a portable and
multifunctional measuring device. It is
composed of a 131fts (40m) laser distance
module and a 4096-grade angle sensor module
with high accuracy, which empowers its ability
to measure straight lines, curves, and
compound shapes floorplans. MEAZOR 3D is
equipped with a plotting app for Android and
iOS, allowing data collection, floor plan
drawing, 3D display, document receiving, and
sharing.
-The standard edition (Model M0102) can
complete the above essential functions.
-The premium combo (M0102-U) is equipped
with the Ultra 3D Adapter and can is capable of
obstacle avoidance and achieve higher
precision.

SAFETY INSTRUCTIONS
For the safe use of this multifunctional measure,
please read the instructions below carefully.
The device is categorized as a Class 2 laser
product. DO NOT stare directly at the laser or
shoot the laser at other people or animals, or it
will cause damage to the eyes.
This product is in accordance with strict
standards and testing regulations through its
development and manufacturing, but this does
not preclude the product from being subjected
to external environmental influences and
interference.
●Please DO NOT use this product in
extremely hot (>40°C) or extremely cold (<0°C)
environments.
●Please DO NOT use this product in an
explosive or corrosive environment.
●Please DO NOT use this product near
medical devices.
●Please DO NOT use the product on a
plane.
Disposal:
This product contains a rechargeable lithium
battery, which must NOT be disposed of with
household waste. Please dispose of the product
in accordance with the national regulations in
force in your country/region.
Scope of Responsibility:
We will not be responsible for any damage
caused by improper use below:
●Using the product without instruction;
●Use of accessories from other
manufacturers without approval from us;
●Carrying out modification or conversion
of the product.

Laser
Touch Screen
Send / Next Button
Power / Back Button
Type-C Charging Port
Tripod/ Accessory Hole
Wheel Module
BASIC OPERATION
You can swipe left and right on the main menu
to switch between functions or toggle the
wheel to switch between functions quickly. Tap
on the selected function icon to enter the
function page.

1 2 3
Type-C Charging Port
Tripod/ Accessory Hole
Wheel Module
Open Flip Stand
Power Button
Sleep
Turn Off
Charging
2 sec > ON / OFF
30sec > Sleep
2 min > OFF
1.5-2 hrs > 100%
Stand - Flip the back flap. The flap is magnetically
attached to the product's frame at an angle of 90°.
The stand allows the user to perform vertical
measuring tasks.
BASIC OPERATION

Stand - Flip the back flap. The flap is magnetically
attached to the product's frame at an angle of 90°.
The stand allows the user to perform vertical
measuring tasks.
* The Ultra 3D Adapter is only included in the
combo edition(M0102-U). For standard model
(M0102) users, the Ultra 3D Adapter in the
picture needs to be purchased separately if
required.
* The Master Tripod shown in the picture needs
to be purchased separately if required.
Mounting the handle and tightening
the tripod
Adjust the tripod feet until the two
horizontal bubble levels are centered
SETUP 3D ADAPTER

90°
Install MEAZOR 3D by magnetically attaching the
device to the Adapter. Please make sure to the
device is well-coonected to the Adapter and
confirm the installation is in place.
Open the vertical stand and adjust the Adapter
until it is level with the ground.
Enter the point scanner/curve scanner function,
wait 5 seconds for level calibration, and then tap
the screen to skip the Setup Guide and to start
scanning.
SETUP 3D ADAPTER

1 2
LASER MEASURE
The setting of the measurement units: set at initialization or in the
setup page , the user can select between imperial or metric units.
When measuring, the user can also switch between units by tapping
on the top area. Imperial units include Yard, Feet, Inch, Inch fraction.
Metric units include m, cm, mm.
*Note:
- If MEAZOR 3D is connected via Bluetooth to MEAZOR/3rd party
App, press the middle section (measuring result) or press the
Record Button. It will record and send data to the connected
App. If not connected via Bluetooth, pressing the middle section
will clear data.
- If MEAZOR 3D performs a measuring task oine (not
connected to App), please press Save Data on the touch screen
to record measuring results to the built-in data storage.
1) BACK ALIGN: measure along the bottom of
the MEAZOR's roller as a starting point
3) TRIPOD ALIGN: measure from the center
of the tripod hole
4) FRONT ALIGN: measure from the top of
the product.
2) STAND ALIGN: with the stand open, measure
from the bottom of the stand.
Switch Units
Save Data
Switch Align
Mode
Clear / send*

US-ARCH US-ENG
METRIC-
ARCH
METRIC-
ENG
1/16" = 1' 1" = 1" 1:1 1:10 0
3/32" = 1' 1" = 10 ' 1:2 1:125
1/8" = 1' 1" = 20 ' 1:3 1:150
3/16" = 1' 1" = 30 ' 1:4 1:20 0
1/4 " = 1' 1" = 4 0 ' 1:5 1:250
3/8" = 1' 1" = 50 ' 1:10 1:30 0
1/2" = 1' 1"= 60 ' 1:20 1:4 0 0
3/4 " = 1' 1" = 70 ' 1:25 1:50 0
1" = 1' 1" = 80 ' 1:30 1:10 0 0
1 1/2" = 1' 1" = 90 ' 1:4 0 1:1250
2" = 1' 1" = 10 0 ' 1:50 1:150 0
3" = 1'
1" = 166.6'
1:72 1:1625
4 " = 1' 1" = 20 0 ' 1:75 1:20 0 0
6" = 1' 1" = 250 ' 1:10 0 1:250 0
1' = 1' 1:50 0 0
*Note:
- If MEAZOR 3D is connected via Bluetooth to MEAZOR/3rd party
App, press the middle section (measuring result) or press the
Record Button. It will record and send data to the connected
App. If not connected via Bluetooth, pressing the middle section
will clear data.
- If MEAZOR 3D performs a measuring task oine (not
connected to App), please press Save Data on the touch screen
to record measuring results to the built-in data storage.
ROLLING RULER
1) MEASURE OBJECT ( 1:1 )
2) MEASURE IN SCALES ( 58 scales total )
The scale mode includes four scale modes (selected in the setting
menu), a total of 58 measurement scales
Switch Units
Save Data
Scale Setting
Current Scale
Clear / send*

1
2
3
4
5
6
*Note:
- If MEAZOR 3D is connected via Bluetooth to MEAZOR/3rd party
App, press the middle section (measuring result) or press the
Record Button. It will record and send data to the connected
App. If not connected via Bluetooth, pressing the middle section
will clear data.
- If MEAZOR 3D performs a measuring task oine (not
connected to App), please press Save Data on the touch screen
to record measuring results to the built-in data storage.
Undo
Send Data
Displacement
Mode
POINT SCANNER
Use Master Tripod for better result
(sold seperately)
1) Installation
2) Start to Scan
As shown in the diagram, place the MEAZOR 3D
in the middle of the room. Align the laser beam
with point 1 and tap on it to record the first
reference point, turn and align it with point 2,
record, rotate, and align it with points 3,4,5 and
record each time. After completing the above
steps, all the reference points of the room are
captured. After tapping on save , the data will be
sent to the MEAZOR APP.

1
2
3
4
5
Tilt Mode
Suppose an obstacle is placed in between the line
towards a reference point. In that case, Tilt Mode
is automatically switched on while vertically
lifting up or down the device with the support of
Ultra 3D Adapter.
e.g., as shown in the diagram, the user needs to
capture reference points 1-5 to avoid the obstacle
at the corner and plot the complete floorplan.
With Tilt Mode's algorithm, the measuring result
will appear like the floorplan in the blue outlines
shown above.
*The Ultra 3D Adapter is required to use Tilt Mode.
**HOZO assumes no responsibility with regard to
the measuring result accuracy if the measuring
tasks involve Tilt Mode, but the user fails to use
the Ultra 3D Adapter.
***HOZO assumes no responsibility with regard to
the selection, performance, or use of third-party
accessories. HOZO makes no representations
regarding third-party accessories' accuracy or
reliability.
Vertical tilt angle

A
B
A
B
When you are scanning a complex room with the
MEAZOR 3D , and the obstruction of the walls
stops the laser beam from measuring the full
extent of the room, you can turn on the
Displacement Mode to measure more space by
moving the MEAZOR 3D around. Please carefully
read the steps for using this function.
1) Before the MEAZOR 3D is displaced, identify
reference point A and reference point B.
2) Move MEAZOR 3D to a new position.
3) Confirm the new position of MEAZOR by
rotating the MEAZOR 3D to reposition points A
and B.
4) Continue to complete the scanning.
*Note: After the MEAZOR 3D has been moved, the
system will continue scanning along the last
endpoint of the previous measurement.
**Using MEAZOR 3D Reusable Target Plates is recommended
to facilitate Displacement Mode to get better results while
capturing reference points.
Suppose an obstacle is placed in between the line
towards a reference point. In that case, Tilt Mode
is automatically switched on while vertically
lifting up or down the device with the support of
Ultra 3D Adapter.
e.g., as shown in the diagram, the user needs to
capture reference points 1-5 to avoid the obstacle
at the corner and plot the complete floorplan.
With Tilt Mode's algorithm, the measuring result
will appear like the floorplan in the blue outlines
shown above.
*The Ultra 3D Adapter is required to use Tilt Mode.
**HOZO assumes no responsibility with regard to
the measuring result accuracy if the measuring
tasks involve Tilt Mode, but the user fails to use
the Ultra 3D Adapter.
***HOZO assumes no responsibility with regard to
the selection, performance, or use of third-party
accessories. HOZO makes no representations
regarding third-party accessories' accuracy or
reliability.
Displacement Mode

CURVE SCANNER
1) Installation
2) Start to Scan
Use Master Tripod for better result
(sold seperately)
As shown in the diagram, place the MEAZOR in
the middle of the room. Align the laser beam with
the start-point and tap on it to record the first
reference point, slowly rotating MEAZOR 3D to
the end-point.
Undo
Send Data
Tilt Mode

1
3
1
2
2
Pythagorean Mode
PRO-LASER
Area Mode
PRO-LASER
Pythagorean Mode (horizontal angle
ONLY) – Measure side A, side B, and the
angle ∠ab. The length of the third side is
automatically calculated.
Area Mode – Measure the length A and the
width B. The area is automatically
calculated.
As shown in the diagram, place the MEAZOR in
the middle of the room. Align the laser beam with
the start-point and tap on it to record the first
reference point, slowly rotating MEAZOR 3D to
the end-point.

1) Rotate wheel to measure angle
2) Laser line to improve accuracy
PROTRACTOR
Place MEAZOR 3D on a flat surface, rotate
MEAZOR 3D to measure the horizontal angle.
While the angle is being measured, MEAZOR 3D’s
laser module can be used to locate the
start/endpoint of the angle.
The MEAZOR Expert Protractor Accessory (sold
separately) can also be used for more accurate
angle measurement.
Back to zero
Laser-assisted
positioning
Degree/Index
Mode
Area Mode – Measure the length A and the
width B. The area is automatically
calculated.
Need protractor accessory
(sold seperately)

1
2
1) Calibrate on Floor
2) Start Leveling
LEVEL
Place MEAZOR 3D on a flat surface to use the
electronic level function of MEAZOR 3D. When the
level is close to 0° (< ± 1°), the light point turns
blue.
Horizontal axis: Tumble angle / Vertical axis: Tilt
angle

MEAZOR APP
The above product specifications are subject to
change without notice. All rights of interpretation
are reserved by HOZO DESIGN CO., Limited.
All trademarks, images, technical data, and
intellectual property rights are the properties of
HOZO DESIGN CO., Limited and are subject to
copyright infringement.
Connect to MEAZOR APP
MEAZOR APP is a free app and can be connected
to MEAZOR series products. Receive surveying
data and edit it. After entering the MEAZOR APP,
create a new project. And click the Bluetooth icon
in the upper right corner to connect to MEAZOR
3D.
Place MEAZOR 3D on a flat surface to use the
electronic level function of MEAZOR 3D. When the
level is close to 0° (< ± 1°), the light point turns
blue.