Meco Smart Home Video Doorbell Instruction manual

Please consult below checklist for all the components.
1. What’s in the box
2. Meet the doorbell
3. Meet the chime
User GuideUSB Cable
Video Doorbell
Double-sided Tape
3
2
1
10
11
12
6
5
4
7
8
9
2MP Camera
PIR Motion Sensor
Speakers
Indicating LED
Doorbell Button
Microphone
Charging Indicator
Micro USB Port
Reset
Wall-mount bracket
SD Card Slot
Battery Compartment
3
2
1
4
6
5
8
7
10
9
12
11
1
3
2
4
Speakers
Reset
LED Indicator
USB Port (Type-A/M)
2
1 3
4
4. Battery installation
Indoor Chime Screw & Tools
- 1 -
The batteries are pre-installed in the doorbell. If you have taken out the
batteries, please note the electrodes when installing batteries. Please insert the
batteries with positive poles upward!
NOTE:
Improper battery installation will cause damage to the internal components and may
result in serious injury.

The batteries inside the doorbell are not fully charged in accordance with
transportation safety regulations.
Please charge the batteries with a USB compatible wall charger (not included)
and the provided USB cable for about 8~10 hours prior to Wi-Fi configuration
and installation.
Please install a battery for the doorbell
Press the [Bell] button to wake the device if it
is asleep
Please stay near your router for the best signal
Install Doorbell
Next
9:55
· Using the supplied reset pin, reset the
device(please consult the user manual for more on
this)
· Wait for the LED indicator to flash RED
· Tap Next
Please reset the device
Install Doorbell
Next
9:55
5. Battery charging
6. Download the app
7. Wi-Fi set up
Camera
Battery Camera Floodlight Camera
Network Video
Recorder
Doorbell
9:55
Devices Messages MeFriends
Tap + to add a new device
Devices
- 2 -
1. Tap on “+” to add device 2. Select doorbell 3. Check the power status 4. Reset the doorbell
Before you start the Wi-Fi configuration, please note below:
1). The doorbell works with 2.4 GHz Wi-Fi, but not with 5 GHz Wi-Fi.
2). Avoid using special characters or symbols like )(@~!#$%^&*..., either in your Wi-Fi name or password.
3). Perform the configuration near your Wi-Fi router.
Launch the CloudEdge APP and register an account with your mobile phone numer of email ID. Then start the Wi-Fi
Before you start the Wi-Fi configuration, please note below:
Download and install the 'CloudEdge' app from Google PlayTM or the
App StoreTM. The App is also available by scanning the QR codes on
the right, using your QR code scanner in your smart phone.
NOTE: Google PlayTM is a trademark of Google Inc. App StoreTM is a
service mark of Apple Inc.
Android
iOS
CloudEdge

Install Doorbell
Press the [Bell] button, and tap Next
Help
Next
9:55
Select your Wi-Fi network
Change WiFi
Hide Password
Home
Password123
(Please select a 2.4G network, this device will not
work with 5G Wi-Fi networks)
Wi-Fi Setup
Next
9:55
Operation Scan QR Code
Scan the QR code below with the
device at a distance of 5-8 inches.
A tone will be heard when
successfully scanned.
Help Next
Next
9:55
Please remove all film from the lens. Tap
Next to show a QR code, and let your device
scan the code. Keep your phone 5-8 inches
from the lens.
8. Run a test
Devices
9:55
056853326
9:55
Please stay near your router for the
best signal
Device Found!
Connecting device to network...
Registering device...
12%
connecting...
Connect Network
- 3 -
5. Activate the doorbell 6. Input Wi-Fi password 7. Prepare the scanning 8. Generate the QR code
9. Wait for Wi-Fi connection 10. Adding device succeeds
After setup, tap on the live view window in the app
for a test. Then take your doorbell outside to the
installation spot and run a test there. Make sure the
installation spot is covered by strong 2.4 GHz Wi-Fi
signal.
Note:
If the video quality from the doorbell outside is not as
good as it was indoors, you may need to move your
router closer to your installation spot, or invest in an
Wi-Fi extender.

HD
10. Leave a voice message
9. Live view interface
3
6
9
4
1
7
10
13
2
5
8
11
14
Quit live viewing
Volume on/off
Stream bit rate
Speak to the scene
Notification history
Setting menu
HD/SD switch
Wi-Fi signal status
Record on the phone
Cloud storage service
12
Battery status
Wi-Fi signal status
Screenshot button
Body detection on/off
- 4 -
Delete Device
Please hold the recod button to leave a
message for up to 30 seconds. The
voice message is used to answer the
doorbell when the owner is not at home
Tips
Cancel
Device Share
Receive Notifications
Device Information
Basic Function
Alarm Setting
Device Version
SD Card
Cloud Server
Settings
Please confirm whether to let
the doorbell play the
message?
Night Vision
Host Leaves Message
Wireless Chime
Power Management
Automatic
BasicFunction
Display box of people detection
You can leave a maximum 30-second voice message on the on-board memory of your doorbell, so as to quickly
respond your visitor by a tap on your phone when you are not convenient to answer the doorbell call. The voice
message function is available even without a pre-installed Micro-SD card.
STEPS:
Setting -> Basic function -> Host Leaves Message -> Record your message -> Hang off the incoming call and play the voice
message.