MEE H6D User manual

H6D BLUETOOTH
WIRELESS HEADSET
WITH DOCK AND BOOM MICROPHONE
POWERED BY

H6D BLUETOOTH
WIRELESS HEADSET
Package Contents
Micro-USB
charging cable
Charging
dock
H6D Bluetooth
wireless headset

Package Overview
Volume down button
Status indicator light
Micro-USB charging port
Charging dock connector
Multifunction button
Volume up button
Microphone
A
B
C
D
E
F
G
H
I
J
Headset dock connector
Power indicator light
Micro-USB power port
A B C D E F G
H I J
Headset
Charging Dock

Charging
Connect the dock to any
powered USB port using
the included micro-USB
cable. The red power
indicator light on the
charging dock will light up.
Place headset on
charging dock.
Low battery is indicated by a flashing red status indicator
light and “battery low” voice notification every five minutes.
Charging time is approximately 2 hours. The red status
indicator light on the headset will turn blue once fully
charged.
Option 1:
Using Charging Dock
PORT
USB
Directly connect the H6D headset to any powered USB port
using the included micro-USB cable.
Option 2: Using USB Cable
PORT
USB

Pairing
Press and hold the Multifunction button for about 8 seconds
until the status indicator light flashes red and blue.
Note: The headset will enter pairing mode automatically on
first use or after being reset.

Pairing (Continued)
Open the Bluetooth menu on the device you wish to pair
(usually located in Settings->Bluetooth). If needed, select
“search for devices”, “pair new device”, or “refresh.”
Select “MEE audio H6” and allow pairing to complete. Use
“0000” if a pin is required.
Note: It is only necessary to pair your headset once with
each device.
AT&T LTE 12:26 PM 95%
Bluetooth
Settings
Searching...
Bluetooth
Devices
AT&T LTE 12:26 PM 95%
Bluetooth
Settings
MEE audio H6
Bluetooth

The H6D stores previously paired devices and reconnects
automatically with the last paired Bluetooth device when
powered on.
If the headset does not connect automatically, open the
Bluetooth menu on your device and select “MEE audio H6”
from the Bluetooth device list.
Reconnecting to Paired Devices

Wearing
Adjust the boom mic for
use on the left or right ear.
Adjust the headband to a
comfortable length.

Basic Functionality & Controls
*Not all devices support this functionality. For more information, refer to the
user manual for your device.
**To start playing music, open a music app on your device and start
playback.
Volume Down / Previous Track button
- Decrease Volume
- Previous Track
(during media playback**)
[TAP]
[HOLD 2 sec]
- Increase Volume
- Next Track
(during media playback**)
Multifunction button
[TAP]
[HOLD 2 sec]
[TAP]
[HOLD 2 sec]
[TAP twice]
[TAP]
- Answer Incoming Call
- Reject Incoming Call
- Hang Up
- Siri®/ Voice Command /
Voice Dialing*
- Redial*
- Play / Pause
(during media playback**)
[TAP]
[HOLD 2 sec]
[HOLD 2 sec]
[HOLD 5 sec]
- Power On
- Power Off
Volume Up / Skip Track button

Select “MEE audio H6” and allow pairing to complete. Use
“0000” if a pin is required.
Note: It is only necessary to pair your headset once with
each device.
Multipoint Functionality
Multipoint allows two Bluetooth devices to be connected to
the headset simultaneously.
To use two Bluetooth devices with the H6D, first pair each
one by following the pairing procedure described in the
Pairing section, then power the headset off.
When powered on again, the headset will be able to connect
to both devices. If one of the devices does not connect
automatically, select “MEE audio H6” from the Bluetooth
menu of the device.
To switch between the two connected devices, pause audio
playback on the active device and start audio playback on
the other connected device. It may take up to 30 seconds for
the audio to switch.
Incoming calls will always take precedence over media. The
H6D will automatically activate the connected device that
has an incoming call.

Clear Memory (Delete Paired Devices)
To delete all previous Bluetooth pairings
from memory, first power the headset
on, then press and hold the Volume Up
and Volume Down buttons at the same
time for 5 seconds until the status
indicator light flashes pink.
A new pairing will need to be created
before the H6D can be used again by
following the pairing procedure
described in the Pairing section.

Support
For Additional Support
Visit our Bluetooth Support Guide at MEEaudio.com/Bluetooth for additional Bluetooth
setup information
Still Have Questions?
Email Support: [email protected]
Safety and Care
Clean with a soft cloth, damp with diluted soap water solution if necessary. Do not
use chemical cleaners.
Battery performance will be severely decreased when stored in extreme
temperatures: below -10°C/14°F or above 45°C/113°F including direct sunlight.
The lifetime of the battery will be significantly reduced if your headset is not charged
for a long time. It is recommended to charge your headset at least once a month.
•
•
•
Warranty
MEE audio products purchased from authorized resellers are covered by a 1-year
manufacturer warranty. For more information, visit MEEaudio.com/support
Warnings
Using headphones at high volumes for extended periods of time will result in permanent
hearing damage. It is advised you keep volume levels moderate to low at all times for your
safety. Turn the volume all the way down after connecting your headset, then gradually
increase the volume until you reach a comfortable listening level.
Keep the device and packaging out of reach of children.
This device is designed and manufactured to operate within its defined design limits.
Misuse may result in electric shock or fire. Read and follow these instructions carefully.
To prevent fire or shock hazards, do not expose this unit to rain or moisture. If the
device comes in contact with liquids, quickly wipe away. If submersed in water, do
not turn the device on until completely dried. Note: liquid submersion voids the
warranty.
Danger of explosion or fire if batteries are damaged. Keep away from direct sunlight,
naked flames, flammable gasses, or heat sources such as radiators or stoves
There are no user replaceable/reparable parts in the headset. Disassembling it will
void your warranty.
Only use attachments/accessories specified by the manufacturer
Changes or modifications to this unit not expressly approved by MEE audio could void the
user’s authority to operate the equipment.
•
•
•
•

FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Relocate the receiving antenna.
Increase the separation between equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
•
•
•
Disposal and Recycling
Dispose of this product in accordance with all local laws and regulations. Because this
product contains electronic components and a battery, it must be disposed of separately
from household waste. Contact local authorities to learn about disposal and recycling
options.
Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

MEE audio and its logo are registered trademarks of S2E, Inc. All rights reserved.
The Bluetooth®word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by MEE audio is under license. Other trademarks and
trade names are those of their respective owners.
Siri®is a registered trademark of Apple Inc.
All other trademarks are the property of their respective owners.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
For more information about this warning visit MEEaudio.com/prop65