MEEPO MINI DUAL User manual

MEEPO SMINI DUALMEEPO

⚠ YOUR BOARD MAY LOSE POWER AND BRAKES due to radio
interference, a malfunctioning battery, downhill overcharging of the
battery, or other factors. Only ride your Meepo board at speeds and
on hills where you don’t have to depend on breaks and acceleration.
⚠ BRAKING DOWNHILL WITH A FULL BATTERY WILL CAUSE THE
BOARD TO SHUT DOWN since regenerative braking will overcharge
the battery. To prevent this from happening, the remote will warn you
by beeping, and disable your braking power. Safely come to a stop
before this happens, and ride on flats or uphill to drain the battery
before attempting to ride downhill again.
⚠ WARNING! IN EXPERT AND PRO MODE THE THROTTLE IS
EXTREMELY SENSITVE which means the board can accelerate aggres-
sively causing you to fall off. Try to start by moving slowly in these
modes to ensure safety.
⚠ HILLS AND HIGH SPEEDS CAN BE VERY DANGEROUS,
crashes in these conditions may cause serious injury. Be extra careful
when pushing the limits of the board, even if you’re an experienced
rider.
⚠ CARS AND OTHER VEHICLES CAN INJURE YOU so always be aware
of your surroundings when riding in the presence of vehicles. Ride
defensively and assume the vehicles can’t see you. Remember that
your board may lose power and brakes at any moment. Whenever you
are riding, please be aware of the laws that govern the use of your
board on public roads, bike paths, sidewalks, or other places that you
may ride.
⚠ ALWAYS WEAR A HELMET. Other safety gear, like gloves, pads, and
long sleeves, are highly recommended.
READ THE MANUAL CAREFULLY
BEFORE YOU RIDE

⚠ WARNING! ⚠
WARNING: Whenever riding a Meepo board, safety is your top
priority. Loss of control, collisions, and falls may cause serious injury
to you.
WARNING: Always wear a helmet when riding. Never ride in the
rain, or on wet, slippery or uneven surfaces with steep hills, traffic,
cracks, train tracks, gravel, rocks or any obstacles that could cause a
loss of traction. Avoid night riding in areas with poor visibility or
narrow spaces.
WARNING: Never ride the board at speeds where you do not feel
comfortable. In the event of wireless interference or battery fault,
you may need to rely on skating techniques like footbraking or
sliding to stop. Here is a video for you to learn the skill.
https://www.youtube.com/watch?v=l3EyJPm2E6s.
Please ride responsibly and respect those around you. How you ride
will determine how people view this new mode of transportation. ☺
WARNING: AVOID WATER!
Riding in wet conditions or through puddles can damage the board’s
electronics and cause the board to lose power or stop suddenly. Damage to
the board due to water exposure is not covered under the warranty.
WARNING: PINCH POINTS
Keep fingers, hair, and clothing away from motors, wheels, and all moving
parts.
WARNING: RISK OF ELECTRIC SHOCK!
Do not open or tamper the case or battery with cleaning products, this will
void the board’s warranty.

1
M5 REMOTE
+
Pairing the Remote and Board
1. Turn on Meepo board, then long press the switch for 7 seconds.
2. Press the power button on the remote for 3 seconds to turn it on.
3. Press the power and function-button on the remote at the same
time.
After pairing, double press
to change 'forward' and 'backward'
Function 2.
Hold the throttle down and stay at
the brake position, press ‘‘function’
button to change brake mode.
Function 3.
Before pairing, press and hold
'power' and 'function' button at the
same time to change the speed units
between 'kph' and 'mph' .
Function 1.
Single press to change speed mode
from'LO' to 'MI', 'HI', and 'PRO'.
Brake
Acceleration
Power Button
Speed Mode
Skateboard
Battery Remaining
Remote Control
Battery Remaining
Lanyard
Type-c
Charging Port
5V/ 1A
Function Button
Connected
(Flashing green light）
Disconnected (Green light)
Backward Mode (Flashing red light）
100% 75% 50% 25%
PRO HI MI LO
(When the remote’s power on)
Flashing red light (Under 15%)

2
MEEPO MINI DUAL
700MM
260MM
Front Truck
Front Wheels
Power Button
Charging Port
Deck
ESC and Battery Case
Hub Motors
Bushings

3
Get Ready to Ride
• Always wear a helmet.
• Find a flat, paved area with no obstacles for your first
ride.
• Read and understand the entire manual.
• For more details, check out our website: www.meepoboard.com.
• Other protective equipment is highly recommended.
AVOID THESE OBJECTS AS THEY CAN MAKE YOU LOOSE
CONTROL OR CRASH:
Downhill
Grates/Drains
Poor Visibility
Uphill
Tracks
Obstacles
Water
Larger Rocks
Night Time
Gravel
Cracks
Traffic

4
Riding Basics
ARE YOU A “REGULAR” OR “GOOFY” FOOTED RIDER?
Typically, if you kick a ball with your right foot, you are a regular footed
rider. However, this is not always the case! Try both stances to see
what feels best. If you don’t know which to choose, one advantage of
riding goofy footed is that you have a better view of the traffic.
STANCE
Your Meepo board has a lot of power. Follow these tips to ensure a
safe riding experience:
• Move the throttle wheel in small increments.
• Keep a wide stance on the board.
• Keep a low center of gravity.
• Lean forward when accelerating.
• Lean backward when braking.
L
R
R
L
Regular Goofy

5
Power On/Off the Remote
Press the power-button
for 2 seconds
6
Power On/Off the Board
Press the power button once
or push-start the board.
2S
2S

7
Check the Remote-Board Pairing*
* Your board and remote have already been paired in the factory. You
need to do the following procedure when pairing a new remote to a
board.
2S
2S
• Turn on the board by pressing the power button on the board once.
• Turn on the remote by long pressing the “power” button on the
remote.
• Make sure the old remote is turned off, if you have one.
• Hold the power button on the board for 7 seconds.
• Press the “power” and “function” buttons on the remote at the
same time.
• The connection light on the remote will flash green light.
• When the power button blinks rapidly and the remote displays all
the specs, the board and remote have been paired.

8Operating the Board with the Remote
9
Check the Board Battery Life on the Remote
++
+
Forward
Brake
Skateboard
Battery Remaining
100% 75% 50% 25%
(When the remote’s power on)
The remote is equipped with
battery indicator lights below
the power button.
When your remote’s power on,
the remote lights will indicate
the power level.

10Change Ride Mode
The board is set in beginner mode by default. Before switching
modes, make sure you have mastered the beginner mode.
LO: Limited acceleration, top speed of 7km/h (4.5mph).
MI: Moderate acceleration, top speed of 14km/h (9mph).
HI: High acceleration, top speed of 33km/h (20.5mph).
PRO: Max acceleration, top speed of 33km/h (20.5mph).
WARNING: The throttle wheel is much more sensitive in HI and PRO
modes. To avoid getting thrown off from the board, follow these tips:
• Start by moving forward slowly.
• Move the throttle wheel in small increments.
• Keep a wide stance on the board.
• Keep a low center of gravity.
• Lean forward when accelerating.
• Lean backward when braking.
It usually takes the remote several hours to get fully charged. If the
board and remote are charged at the same time, the remote will be
charged first.
CYCLE THROUGH SPEED /BRAKE MODES:
While holding the throttle down press the
function-button to change brake modes.
Press the function-button once to change
speed modes.

11Charge the Remote
12
Charge the Board
Warning: Never leave your
board unattended while
charging. Charging Port
Charging Port
The remote takes several hours to
charge. If the board and remote are
charged at the same time, the remote
should finish charging before the board.

13Remove the Battery Pack
14
Replace the Battery Pack
• Ensure that the board is turned off.
• Take the grip tape off.
• Use a 3mm hex wrench to remove the six bolts that fasten the
battery pack to the deck.
• Lift the battery pack to reveal the connector between the deck and
battery pack.
• Carefully twist and pull the connector apart.
• To insert a new battery pack, align the grooves on both ends of the
connector (board & battery pack).
• Insert, connect, and adjust the two ends of the connector together.
Make sure to tighten the connector to make a good seal.
• Ensure the connector lays flat within the accessory wire and the
groove of the board.
• Replace and tighten the bolts with the hex wrench, and put the grip
tape back on.

15More Information Online
This manual is a quick start guide intended for someone with little
experience in riding electric skateboards. If you want to learn more
on how to start riding, superior riding skills, and solutions for riding
problems, please visit our website: www.meepoboard.com or send
us a mail to [email protected].
GETTING STARTED
• How to stand on the board
• How to turn
• How to find a good spot to practice
ADVANCED TECHNIQUES
• How to footbrake
• How to ride uphill and downhill safely
• What to look for when riding through traffic
MAINTENANCE
• Pre-ride inspection
• Routine maintenance
This equipment has been tested and complies with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and radiates radio frequency energy. If not installed
and used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation.
16
Warnings and Safety Information

If this equipment does radiate harmful interference to radio or
television reception, fix the problem by trying one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a different circuit from
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Prolonged exposure to sunlight may discolor or weaken the plastic
cases, as they are not UV Rated.
IMPORTANT Safety and Handling Information
Do not attempt to disassemble the product without
consulting Meepo. Should your unit need service,
contact our Customer Service by sending an email to
[email protected].
Product Specifications
• Meepo Mini D ual Skateboard: Rated Input: 42Vdc, 1A
M5 Remote:Rated Input: 5Vdc, 500-1000mA Operating
Temperature: 0-40°C, 10-90% RH
• The board specifications were obtained under perfect condi-
tions. Each customer will have different conditions that will
make the eboard performance fluctuate from the data we
present.
Battery Safety and Handling Information
CAUTION
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to instructions.
CAUTION
Failure to follow these safety instructions could result in fire,
electric shock, or other injury or damage to the Meepo Mini
Dual skateboard and Meepo M5 remote or other property.

Battery Charging Information
The charger supplied with the electric skateboard
should be regularly examined for damage to the cord,
plug, enclosure, and other parts. In the event of such
damage, the skateboard must not be charged until
the charger has been repaired or replaced.
Changes or modifications to the skateboard unapproved by Meepo
may void the user’s warranty.
This product is intended to be equipped only with M eepo Mini Dual
batteries.
Do not drop or throw the battery.
Keep the battery away from kids.
Never expose this product or the battery to any liquids.
Never throw the battery into a fire, it could cause the battery to
explode.
Never bring the connector terminals in contact with another metal
object, it will short-circuit the battery. Short-circuit could cause
personal injury, fires or damage to the battery.
Your device contains an internal rechargeable lithium-ion battery
which may present a risk of fire or chemical burn if mistreated. Do not
charge or use the unit in a car or places where the temperature
surpasses 40°C.
Unplug the charger and disconnect it from the skateboard when not
in use.
CAUTION
Only use the dedicated charger provided for this unit.

The charger is designed for indoor use only. Do not expose the
charger to liquid, moisture or extreme humidity. Do not charge
Meepo Mini Dual skateboard or Meepo M5 remote outdoors or in the
rain.
Stop charging the skateboard and/or remote if charging isn’t complet-
ed within the specified time.
Stop charging the skateboard and/or remote if the batteries become
abnormally hot, show signs of odor, discoloration, deformation, or if
abnormal conditions are detected during use, charging, or storage.
Do not charge the skateboard and/or remote if the battery enclosure
becomes cracked, swollen, or shows any other signs of damage.
Discontinue use immediately and promptly dispose of unit.
Product and Battery Disposal Information:
Your device should not be placed in municipal waste. Please check
local regulations for proper disposal of electronic products.
If this unit shows any type of damage, such as bulging, swelling, or
malformation, discontinue use and immediately contact Customer
Service by sending a mail to [email protected].
Dispose of used batteries in accordance with the prevailing communi-
ty regulations that apply to the disposal of batteries.
Never dispose of used batteries with other ordinary solid wastes.
Batteries contain toxic substances.
WARNING
Power cord is used as a disconnection device. To fully
de-energize equipment for service, disconnect the charger
power cord.

LIMITED WARRANTY
If the product has a manufacturing defect within 180 days of ship date,
contact [email protected]
Each board was tested for at least 20 miles before shipping it out. So it
is normal to spot some dirt or dust on the board, and certain mileage
on the remote.
FOR ALL RETURN AND WARRANTY SHIPPING:
Please keep your shipping box. The warranty does not include damage
from return shipping with lack of package material.
For any concerns regarding your board, please contact Meepo’s
customer service by going to www.meepoboard.com or by emailing
[email protected].
MAINTENANCE AFTER WET SURFACES
If you accidently ride in the rain or on wet surfaces, wipe off all the
water on the surface of your board, especially the charging port. Do not
charge your board until it is completely dry. Then, run the motors so
that the wheels are spinning for 10 minutes in order to dry the inside
of the motors and avoid rust.
MAINTENANCE FOR UNUSED BOARD
Store your board in a dry area and fully charge your board at least once
a month to avoid unrecoverable battery damage if you are not going to
ride your board for a long time.
WARRANTY AND MAINTENANCE
This board is covered by a 180 day manufacturer’s warranty that covers
defects in workmanship and material. This does not cover damage
caused by abuse, misuse, negligence, accidents, or riding in water.

Online Store: www.meepoboard.com
Customer Service Email Address: [email protected]
Meepo Electric Skateboard Company
Online Store Customer Service
Company address : Room 2015, Trend Centre, 29-31 Cheung Lee
Street, Chai Wan, Hong Kong

© MEEPO Inc. 2016-2021 www.meepoboard.com