Mega FX A1 User manual

USER MANUAL
Table of Contents
Safety Information……………………………………...………………3
Specifications………………………………………...…………………4
Main Power Connection…………………………...…………………..5
DMX-512 Connection……………………………..…………………...5
Main Control Menu……………..…………………………………..….6
DMX Profile.....................................................................................8
Rigging the Fixture……………………………….…………………….8
Cleaning & Maintenance.................................................................9
Parts List.........................................................................................9

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured away from unit movement.
6. Maximum surface operating temperature 140º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit risk of electrical shock.
3

4
Specifications
Part Numbers
Fixture Flight Case
2011 - A1 DMX Fan 2011-RC Road Case
Mechanical Specifications
Fixture Flight Case for Shipping
Size: 22.12” x 13.25” x 11.12”
Weight: 23.25lb
DMX Connectors: 3 and 5-pin XLR connectors
Power Connectors: Power Conn Type to Nema 5-15 cable mounted
Thermal: Maximum ambient temperature 110° F
Maximum surface temperature 140° F
Fastening System: Dual quick release mounts (included)
Display: Digital
Output: 34m³/ min. at Max Speed
Fan Blade Size: 11 inch
Electrical Specifications
Power supply: 110V AC 60Hz
Power consumption: Amps 1.36
Watts 152
Size: 19” x 15” x 23.25”
Weight: 32 lb
16.40”
Control & Programming
Protocol: DMX 512
DMX Control Mode: 1 Channel Mode (Fan Speed)
Display: Display control setting for fan speed and timing intervals
11” W/ Eye Bolt
18”

5
Main Power Connection
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit must be earthed. (electronically grounded)
3. Replace fuse only with the specified type and rating.(F4Amp 250V, 20mm)
The occupation of the connection-cable is as follows:
DMX-512 Connection
The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only
use a shielded twisted pair cable designed for RS-485 3 and 5 pin XLR plugs and connectors in order to connect the
controller with the fixture or the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 or 5 pin XLR plug and
plug it in to the last fixture on the signal run. Pre-manufactured terminator plugs are
available for purchase from your Mega-FX dealer (P-DMX-T).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
5
3
4
2
11
2
3
4
5
4. N/A
5. N/A
2
3
11
2
3
LN

6
Main Control Menu
The control board on the fixture base is your interface to access and
control all the functions on the unit. Its LCD display gives you views
of the options and functions. The following will explain each func-
tion and its options. Press Function Button to access control menu
Mega FX
A1
FUNCTION UP DOWN
TIMER VOLUME MANUAL
Duration Set 5s
Mega A1
Duration Set
Sets duration time in Sec or Minutes, that the fan will be on. This
function will only be engaged in Timer mode.
Interval Set 5s
Mega A1
Ready to Use
Mega A1
FUNCTION UP DOWN
TIMER VOLUME MANUAL
Volume Out 1
Mega A1
Volume Out
Sets the fan speed. This function will only be engaged in Timer and
Volume mode.
The Functions Below will adjust the A1 Fan speed when used in Timer, Volume
and Manual Mode.
Interval Set
Sets Interval time in Sec or Minutes the amount of time Between fan
engaged. This function will only be engaged in Timer mode

7
Ready to Use
Mega FX H5
FUNCTION UP DOWN
TIMER VOLUME MANUAL
DMX 512 Add. 1
Mega FX H5
Timing Set Sec
Mega FX H5
Timing Set
Allows you to set the timing increments seconds or minutes for Inter-
vals and Duration. This function will only be engaged in Timer mode.
TIMER Timer
Press once to turn on press again to turn off. Timer mode will en-
gage Interval, Duration and Volume settings.
VOLUME Volume
Press once to turn on press again to turn off. Volume mode will en-
gage Volume=Fan Speed settings.
Manual Manual
Press once and hold, release to turn off. Manual mode will engage
Fan Speed at 100%.
Note: (It is recommended to not run the fan at the lowest
speeds for over 1 hour of time to avoid motor over heating )
DMX Address
Use the up down button to give the fixture the DMX start address
channel. Note: (When fixture is connected to DMX the other func-
tions will not be available)

8
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24 inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
5. Fan bladed spin with out warning. Keep hands, hair and clothes away from fan
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector
has got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
DMX Profile
A1 DMX Fan 1 Channel
DMX Channel Function Description Value Init Value
1Fan Speed Off 0-9255
Slow to Fast 10-255
Note: (It is recommended to not run the fan at the lowest speeds for over 1 hour of time to avoid motor over heating )

Cleaning and Maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installa-
tions and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) Mechanically moved parts like axles and other must not show any traces of wearing and must not rotate with unbal-
ances.
4) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Disconnect from mains before starting maintenance operation!
Caution Danger to life!
The following points need to be addressed when doing maintenance on the fixture.
1) The Fans blades should be cleaned monthly. DO NOT blow high pressure air into fans as incorrect rotation can
damage the fans operation.
2) The fans intake vents need to be cleared from debris and residue.
Note: There is no serviceable parts inside the device. Maintenance and service operations are to be carried out
by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by author-
ized dealers only.
Should you have further questions , please contact your dealer.
9
Parts List
2011-PCBM Main PCB
2011-DIS Display
2001-FH Fuse Holder
2001-PS Power Switch
2011-EMI EMI Filter
2011-CAP Capasitor
2011-TRA Power Transformer
2011-FS Front Metal Screen
2011-RS Rear Metal Screen
2011-QR Quick Release Clamp Mounts
2011-FAN Fan
2011-RC Road Case
Accessories

Mega-FX
18668 Highway 16N
Helotes, TX 78023
Ph 210-684-2600 Fax [phone]
www.megasystemsinc.com / [e-mail]
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.