Megatron CARDANO MT67030 User manual

MEGATRON®
LED Surface Downlight – CARDANO
TECHNICAL SPECIFICATION:
Instruction Manual
CAUTIONS:
∙Read the entire manual carefully before installation and operation.
∙Installation or replacement should be performed only by licensed and qualified electricians.
∙DO NOT disassemble the inner part of the luminaire. Doing so may result in luminaire damage or malfunction.
∙Switch OFF thepower source before installation, replacement and cleaning!
∙Wearing gloves during installation is recommended to ensure the luminaireis kept in the best condition.
∙Before replacement of thelamp or luminaire,turn it off and allow it to cool down.Heat-resistant gloves are mandatory when handling the luminaire.
∙The manufacturer accepts no liability for any damageresulting from the misuse of the luminaire or from when it is used with inappropriate equipment.
∙Important warning for grounddrilling and drillinginwalls: before drilling, make sure that there are no gas and water pipes or power lines behind or near the drilling
spots. Drilling and mounting should be performed only byqualifiedpersonnel. Be sure to pay attentionto the condition and material of the ground and walls, as the
supplied mounting material is not suitable for all ground and wall types. Please inquireabout recommended screws and raw plugs for your ground or wall type and
condition. The manufacturer accepts no liability for improper wall raw plug mounting and the herefrom resulting damages.
∙This product contains alight source of energy efficiency class <X>.
∙Consult your dealer if you have any enquiries.
ATTENTION:
∙Instant start is allowed.
∙The luminaire may only be used with GX53 LED lamps!
∙The operating temperature of the luminaire is -20°C to +40°C.
IDV GmbH | Birkenweiherstraße 2 | D-63505 Langenselbold | Germany | www.megatron-licht.eu
GB
INSTALLATION: MT67030 and MT67033
71
1. Turn OFF the power.
2. Drill the holes and plug the dowels into
the drill holes.
3. Screw the luminaire holder on the wall
or ceiling.
4. Connect the cable to the terminal
block.
5. Place the luminaire in the holder and
tighten the side screws in order to fix.
6. Insert the light source MT67081/
MT67082 into the lamp holder.
7. Turn ON the power.
OFF ON
Series Name MEGATRON® Ambiente
Model Number MT67030 MT67031 MT67032 MT67033 MT67034 MT67035
Color Black White
Lamp Holder GX53 GX53
Incl. Light Source MT67081 MT67082
Light Source Wattage 7W 2 x 7W 3 x 7W 7W 2 x 7W 3 x 7W
Beam Angle
Total Luminous Flux 500lm 2 x 500lm 3 x 500lm 500lm 2 x 500lm 3 x 500lm
Energy Efficiency Class
Light Source <X> G
Voltage 220–240V~
Frequency 50/60 Hz
IP Rating IP20
----
0,2m
LED LED
Replace any cracked
protective shield.
Approx.
8mm
>5cm
90°
1 pcs. 4 pcs. 4 pcs.
INCLUDED PARTS:

Correct disposal of this product:
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly, to promote the sustainable reuse of material resources. To return your device, please use the
return and collection systems, or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
IDV GmbH | Birkenweiherstraße 2 | D-63505 Langenselbold | Germany | www.megatron-licht.eu
GB
----
0,2m
LED LED
MEGATRON®
LED Surface Downlight – CARDANO
Instruction Manual
INSTALLATION: MT67031 and MT67034
INSTALLATION: MT67032 and MT67035
1
1
OFF
OFF
ON
ON
1. Turn OFF the power.
2. Drill the holes and plug the dowels into
the drill holes.
3. Screw the luminaire holder on the wall
or ceiling.
4. Connect the cable to the terminal
block.
5. Place the luminaire in the holder and
tighten the side screws in order to fix.
6. Insert the light source MT67081/
MT67082 into the lamp holder.
7. Turn ON the power.
1. Turn OFF the power.
2. Drill the holes and plug the dowels into
the drill holes.
3. Screw the luminaire holder on the wall
or ceiling.
4. Connect the cable to the terminal
block.
5. Place the luminaire in the holder and
tighten the side screws in order to fix.
6. Insert the light source MT67081/
MT67082 into the lamp holder.
7. Turn ON the power.