Memorex RF Wireless Optical Traveler’s Mouse User manual

RF Wireless Optical Traveler’s Mouse
User Guide

Notice:
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of
this device could void the users authority to operate the equipment.

Congratulations on your purchase of the Memorex RF Wireless Optical Traveler’s
Mouse. Please carefully read the User's Guide to learn about the installation process
and the functions of your new Wireless Optical Traveler’s Mouse.
1. Contents of the Package
1)WirelessOpticalTraveler’s Mouse with two rf channels
2) 1 USB Receiver
3) Two AAA rechargeable Batteries
4) Mouse Driver CD
5) User's Guide (located on the CD)
6) USB to DC Cable
7) Black Travel Bag
2. Installing the Mouse Hardware
2-1. Install the USB Connector of the Receiver into the USB port of the PC. (note –
PC power may remain on).
2-2. Select the Channel and Insert the Batteries into the mouse
The location of the channel switch is inside the battery compartment. Select
Channel "1" or "2" . Put the batteries into the battery case according to the polarity
signs on the device. Select the same channel on the receiver as selected on the
mouse.
2-3. Link the Mouse with the Receiver
1) The LED indicator on the receiver should now be lit.
2) Press the ID Link Button on the receiver and the LED indicator will blink.
The receiver is ready to automatically link with the mouse.
3) Press the ID Link Button on the back of the mouse and the LED indicator
on the receiver will blink quickly. The indicator will stay lit while
successfully finishing the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse for any reason or after changing the
mouse batteries, repeat the steps above.
6) If you experience interference on the selected channel please change the
Link ID by repeating the steps above or select the other channel.

3.Installing the Mouse Driver
3-1. Note this mouse and driver will function on the following operating systems:
Windows 98/2000/ME/XP.
3-2. Installation
1) Insert the driver diskette into the floppy drive of your PC.
2) 2) Explore the diskette and double click the file "Setup.exe"
3) Follow the setup instructions to complete the driver installation.
4) A Mouse Setting icon will appear in the Windows tool bar after you
successfully finish the installation.
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions to set the button functions.
4. Charging the Mouse
1.Connect the mouse to the DC end of the USB to DC Cable.
2. Connect the USB end to the computers USB port.
3. The mouse is now charging.
Notice: Please use rechargeable batteries for the rechargeable mouse.
5. Battery and Charging Notice
1) First time users, please charge the batteries 6 to 8 hours prior to use.
2) The LED indicator or the scroll wheel on the mouse will light when the mouse
battery is low. When this occurs change/ recharge the batteries immediately.
3) To conserve battery life, the mouse is equipped with a sleep mode. The
mouse will enter sleep mode after 10minutes of consecutive non-use. Press any
button to wake up the mouse from this mode.
4) When you are storing the mouse, remove the batteries to conserve battery life.
If the batteries are left in and the mouse button gets bumped, the mouse will
activate and lose battery life.
6. Notice to desktop users:
This mouse is designed for use with a notebook computer. If you are using the
product with a desktop unit, there is a chance for interference to occur. This
interference is caused by the power switching mechanisms between the power supply
and the desktop unit.

If the above instructions do not solve your problem, please contact Memorex
technical support at 877-Is it live (toll free, or visit us online at
www.memorex.com for our Frequently Asked Questions (FAQ) section.
Memorex Products One Year Limited Warranty. Memorex Products, Inc. will replace this
product free of charge if it is found to be defective in materials or workmanship during
normal usage conditions for a period of one year from date of purchase (proof of purchase
required). Other than product replacement (or refund if replacement is not possible),
Memorex Products will not be responsible for any incidental or consequential damages
arising from use of this product.
Product Registration:
To register your product please visit us online at www.memorex.com or write to us with your
name, address, phone number, model name, model number, date of purchase and please of
purchase at: Memorex Products, Inc. 10100 Pioneer Blvd, Suite 110, Santa Fe Springs, CA
90670.