Memorex MT2025D - 20" CRT TV User manual

Before operating the unit, please read this manual thoroughly.
MTD2025D
OWNER S MANUAL'OWNER S MANUAL
20" INCH ANALOG/DIGITAL
TELEVISION
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE
EXIT
ARC CH.LIST
123
456
789
0

The lightning flash with arrowhead
symbol, within an equilateral triangle is
intended to alert the user to the
presence of uninsulated dangerous
voltage within the product's
enclosure that may be of sufficient mag-
nitude to constitute a risk of electric shock.
The exclamation point within an
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompa-
nying the appliance.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PA R TS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
NOTE: Please keep all packaging material for at least 90 days in case you need to return this product to
your place of purchase.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with
the FCC Rules could void the user's authority to operate this equipment.
1
CAUTION:
THIS DIGITALVIDEO PLAYEREMPLOYS ALASER SYSTEM.
TO ENSURE PROPERUSE OF THISPRODUCT,PLEASE READ THISOWNER'S
MANUAL CAREFULLY ANDRETAIN FORFUTURE REFERENCE. SHOULDTHE UNIT
REQUIRE MAINTENANCE, CONTACT ANAUTHORIZED SERVICELOCATION-SEE
SERVICE PROCEDURE.
USE OF CONTROLS,ADJUSTMENTS ORTHE PERFORMANCE OFPROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM,DO NOTTRY TOOPEN THE
ENCLOSURE. VISIBLE LASERRADIATION MAY BE PRESENTWHEN THE ENCLOSURE
IS OPENED.
DO NOT STARE INTO BEAM.

1. READ THESE INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. KEEP THESE INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED ALL WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW ALL INSTRUCTIONS
All operating and use instructions should be followed.
5.CLEAN ONLY WITH DRY CLOTH.
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. DO NOT BLOCKANY VENTILATION OPENINGS. INSTALL INACCORDANCE WITH THE
MANUFACTURER`S INSTRUCTIONS.
7. DO NOT USE THIS APPARATUS NEAR WATER
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
12. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer`s instructions have been adhered to.
13. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company. For
units intended to operate from battery power, or other sources, refer to the operating instructions.
14. GROUNDING OR POLARIZATION
IMPORTANT SAFEGUARDS
S3126A
PORTABLE CART WARNING
(symbol provided by RETAC)
2
Caution - Useof controls oradjustments or performanceof procedures otherthan those specified
herein may resultin hazardous radiationexposure
Product complies withradiation performance standardsunder the FederalFood, Drug andCosmetic Act
11.Use onlywith the cart,stand, tripod, bracket,or table specifiedby
the manufacturer,or sold withthe apparatus. Whena cart isused,
use caution whenmoving the cart/apparatuscombination to avoid
injury from tip-over.
8. Do notinstall near anyheat sources suchas radiators, heatregisters,
stoves, or otherapparatus (including amplifiers)that produce heat.
10. Only useattachments/accessories specified bythe manufacturer.
Do not defeatthe safety purposeof the polarizedor grounding-type plug.Apolarized plug hastwo
blades with onewider than theother.A groundingtype plug hastwo blades anda third grounding
prong. The wideblade or thethird prong are provided for your safety. Ifthe provided plugdoes not
fit into youroutlet, consult anelectrician for replacementof the obsoleteoutlet.
15. Protect thepower cord frombeing walked onor pinched particularlyat plugs, convenience
receptacles, and thepoint where theyexit from theapparatus.
16. Unplug thisapparatus during lightningstorms or whenunused for longperiods of time.
17. Refer allservicing to qualifiedservice personnel. Servicingis required whenthe apparatus
has been damagedin any way, such aspower-supply cord orplug is damaged,liquid has been
spilled or objectshave fallen intothe apparatus, theapparatus has beenexposed to rainor
moisture, does notoperate normally,or has been dropped.

19. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
20. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
21. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
22. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
23. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
24. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
25. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
26. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
27. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
28. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
29. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
30. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
IMPORTANT SAFEGUARDS
3

EXAMPLE OF ANTENNAGROUNDING AS PERTHE
NATIONAL ELECTRICAL CODE
CONDENSATION
Moisture will form in the operating section of the unit if the unit is brought from cool surroundings into a warm
room or if the temperature of the room rises suddenly. When this happens, the unit's performance will be
impaired.
To prevent this, let the unit stand in its new surroundings for about an hour before switching it on, or make sure
that the room temperature rises gradually.
Condensation may also form during the summer if the unit is exposed to the breeze from an air conditioner. In
such cases, change the location of the unit.
31. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
32. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
33. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the CABLE TV system installer s attention to Article 820-40 of the NEC that'
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be con-
nected to the grounding system of the building, as close to the point of cable entry as practical.
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert
the AC cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
Never connect the AC line cord plug to other than the specified
voltage (120V 60Hz). Use the attached power cord only.
If the polarized AC cord does not fit into a non-polarizedAC
outlet, do not attempt to file or cut the blade. It is the user s'
responsibility to have an electrician replace the obsolete outlet.
If you cause a static discharge when touching the unit and the
unit fails to function, simply unplug the unit from the AC outlet
and plug it back in. The unit should return to normal operation.
Polarized AC Cord Plug
(One blade is wider than the other.)
AC Outlet
Wider Hole
and Blade
Power source
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART250, PART H)
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONALELECTRICAL CODE
S2898A
IMPORTANT SAFEGUARDS/POWER SOURCE
4

Contents
IMPORTANT SAFEGUARDS ..........................2
Power source ...................................................4
Contents ...........................................................5
Parts and functions ..........................................6
Remote control .................................................7
Antenna connections ...................................... 9
Cable TV connections .................................... 10
Setting the language ...................................... 12
Manual clock setting ....................................... 14
Before using your unit
TV operation................................................... 15
Closed caption ................................................19
Memorizing channels ......................................17
Setting the Parentalal control ......................... 20
Setting the on timer ........................................ 24
Setting the off timer ........................................ 25
Picture control adjustment.............................. 26
Sound control adjustment ...............................27
TV operation
Reception disturbances...................................54
Problems and troubleshooting ........................55
Problems and troubleshooting/
Video head cleaning...................................56
Specifications ..................................................57
Warranty .........................................................58
Additional information
5
Setting OSD display ....................................... 13

Parts and functions
Front
Rear
AUDIO IN (L/R) jacks
VIDEO IN jack
AUDIO OUT
(L/R) jacks
RF IN (VHF/UHF) jack
VIDEO OUT
jack
6
OUT
IN
VIDEO L AUDIO R
S-VIDEO IN jack

Remote control
7
Battery precautions
The precautions below should be followed when using batteries in this device:
1.Use only the size and type of batteries specified.
2.Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the "-" end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4.If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
Manufacturer's directions.)
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
MODE
S.MODE (Sound) Button No available
ARC( Button
(only in 16 9mode)
Aspect Ratio Control)
CH.LIST Button
Q.VIEW Button
14.
15.
16.
17.
18.
19.
20.
21.
INPUT Button
SAP Button
OK Button
MENU Button
SLEEP Button
CC(Closed Caption) Button
GUIDE Button
TV/DTV

If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your antenna
system. If you are using a cable TV service (CABLE), see the Cable TV connections.
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Antenna connections
75 ohm
coaxial
cable 300-75 ohm
matching
transformer
300-75 ohm
matching
transformer
UHF 300 ohm
VHF 300 ohm
UHF 300 ohm
VHF 75 ohm
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
RF IN
jack RF IN
jack
RF IN
jack
Combiner
RF IN
jack
Combiner
Connect the 75 ohm cable from the combination
VHF/UHF antenna to the RF IN jack.
If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, the use of the 300-75 ohm
matching transformer may be necessary (not sup-
plied).
Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300
ohm twin-lead wire to the 300-75 ohm matching
transformer. Attach thetransformer to the combiner,
then attach the combiner to the RF IN jack.
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner. Attach the combiner
to the RF IN jack.
8

FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a Converter/Descrambler
box, connect the 75 ohm Coaxial Cable directly to the RF IN
Jack on the back of the unit.
Cable TV connections
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
75 ohm
coaxial cable
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the "B"
position, you can directly tune any nonscrambled channels on your unit. With the switch in the "A" position, tune your
unit to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box
to tune scrambled channels.
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
Incoming
75 ohm
cable TV cable 75 ohm cable to
unit
RF IN
jack
RF IN
jack
A
Splitter B
Incoming
75 ohm
cable TV cable
A/B switch
75 ohm cable
to unit
Converter/
descrambler RF IN
jack
Converter/
descrambler
This unit has an extended tuning range and can tune most cable channels without using a Cable TV
Converter box. Some cable companies offer "premium pay channels" in which the signal is
scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device
which is generally provided by the cable company.
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the RF IN jack on the unit. Follow the connections shown
below. Set the unit to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to select channels.
9

Video Game
Using the audio/video inputs
If you connect the TV to a camcorder or Video Game, you can select different modes by pressing INPUT.
Press INPUT repeatedly to select the desired mode.
"AV1 V channel will display on the screen for 4 seconds.", "AV2" , "COMPONENT" , "DVD"or T
To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder to the unit as shown.
To connect the TV to a Video Game
The TV can also be used as a display device for many video games. However, due to the wide variety
of formats, they have not all been included in the suggested connection diagram. Youl need to consult
each component's Owner's Manual for additional information.
Audio/Video cord (not supplied)
To Audio/Video OUT
Camcorder
To Audio/Video OUT
Audio/Video cord (not supplied)
VIDEO IN
AUDIO IN (L)
AUDIO IN (R)
Connections to other equipment (continued)
10
VIDEO IN
AUDIO IN (L)
AUDIO IN (R)
Rear of TV
Rear of TV
AV 1
AV1 AV2 COMPONENT DVD TV Channel

Setting the language and blue screen
You can choose from three different
languages (English, French and
Spanish) for the on-screen displays.
1Press POWER ( ) to turn on the TV.
2 Press MENU, and then
press VOL+/- button to
select FUNCTION menu,
then press CH- button to
enter.
3 Press CH+/- button to select the LANGUAGE option,
then press VOL+/- to select the desired language:
English, Spanish or French.
4 Press MENU until the MENUscreen disappears.
SETTING THE LANGUAGE
0101
LANGUAGE ENGLISH
BLUE SCREEN ON
NTSC CAPTION C1
PARENTALLOCK
FUNCTION
SETTING THE BLUE SCREEN
1 Press MENU, and then
press VOL+/- button to
select FUNCTION menu,
then press CH- button to
enter.
2 Press CH+/- button to select the BLUE SCREEN option,
then press VOL+/- to select OFF or ON.
3 Press MENU until the MENUscreen disappears.
0101
LANGUAGE ENGLISH
BLUE SCREEN ON
NTSC CAPTION C1
PARENTALLOCK
FUNCTION
11
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

FULL/AUTO SCAN (DTV/ATV)
(When using antenna)
The channels broadcastedin DTV and ATV are
automatically scanned and memorized. Only the
receivable channels in the area where this TV is
used will be memorized.
FULL/AUTO SCAN (CATV)
(When using basic cable)
The channels broadcasted in CATV are automatically
scanned and memorized.
NOTE:
Be sure thatantenna or cableis connected properly before plugging the
power cord.
Here describes thecase for searchingand memorizing channels for DTV/ATV.
1 Press MENU, and then press VOL+/- button to select
CHANNEL menu, then press CH- button to enter.
2 Press CH+/- button to
select the RECEPTION
option.
3 Press VOL +/- button
to select AIR/ CABLE.
0101
SKIP OFF
RECEPTION ATV AIR
AUTO SCAN
COLOR SYSTEM AUTO
CHANNEL
When scanning is completed, the memorized
smallest channel will be displayed.
When you pressMENU button while scanning, the
scanning is interruptedand the memorized smallest
channel is displayed.
When you pressVOL+ on the remote control,
scanning the channels in both analog and digital
modes will automaticallystart.
Channel menu
Only in analogsignal
4 Press CH +/- button
to select AUTO SCAN option.
5 Press VOL+ button to start scanning.
12
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

Channel menu
SETTING SKIP
0101
SKIP OFF
RECEPTION ATV AIR
AUTO SCAN
COLOR SYSTEM AUTO
CHANNEL
1 Press MENU, and then
press VOL+/- button to
select CHANNEL menu,
then press CH- button to
enter.
2 Press CH+/- button to
select the SKIP option,
then press VOL+/- button
to select ON or OFF.
SETTING COLOR SYSTEM(only in ATV mode)
After the programs are presetting, you can skipsome
programs so that to select your favorite channels only.
If you wantto recover the skipped channel
1. Use Direct-digit Choosing button to select the number
of the channel to be recovered.
2. Do the above steps again.
3. Press VOL+/- button to set SKIP as Off.
1 Press MENU, and then
press VOL+/- button to
select CHANNEL menu,
then press CH- button to
enter.
2 Press CH+/- button to
select the COLOR
SYSTEM option, then
press VOL+/- button
to select AUTO or NTSC.
0101
SKIP OFF
RECEPTION ATV AIR
AUTO SCAN
COLOR SYSTEM AUTO
CHANNEL
13
NOTE: When tuningDTV channels and no signal is present,
the SKIP-over optionwill be available.
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

You can select the channel by using either CH +/- button
or Channel number buttons. How to select the channel
in each way is shown below.
Channel selection
CABLE
VHF
2-13
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
TV
VHF
2-13
UHF
14-69
CABLE Mode Direct Channel Selection
When the Antenna/Cable menu option is in the Cable position, channels
can be selected as follows:
Press the Direct Channel selection buttons to select the channel.
Antenna Mode Direct Channel Selection
When the Antenna/Cable menu option is in the Antenna position, all channels
can be instantly selected by using
2
2-9: Press 2-9 as needed.
Example, to select channel 2, press"2".
10-69: Press the 2 digits inorder. If you select the channel morethan 69,
the channel will not be change,it is no available.
1 Using CH +/- button
Using CH +/- button on the remote control, change thechannel.
Same operation isavailable with CH +/- button on the frontpanel
of the mainunit.
NOTE:
In the DTVbroadcasting, one channelsometimes broadcasts
multiple programs depending on the airtime. In thiscase, the
main channel iscalled major channeland the subchannel is
called minor channel.
digits button. For example:
14
1-9: Press 1-9 asneeded. Example, to selectchannel 2,
press "2".
10-99: Press the 2digits in order. Example, to select channel 32,
press "3" then "2".
100-125: Press the digital1 button, the "1--"will appear
on the screen, thenpress the 2 digitsof remain in order.
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

This section describes how to adjust the volume when
viewing TV. The MUTE function, which is useful when
you have a visitor or a phone call, will be also described.
1 Using VOL +/- button
Youcan adjust the audio volume with VOL +/- button on
the remote control.
The volume bar is displayed at the bottom of the screen
when adjusting the volume.
Same operation isavailable with VOL +/- on the front
panel of themain unit.
2 Using MUTE button
Press MUTE button on the remote control to mute the
sound.
The colored volume bar is displayed on the screen while
muting.
When CC on,the MUTE will disappear automatically after
a few second
To release the MUTE status, press MUTE button again
or press VOL+ button.
SWITCHING AUDIO
This section describes how to switch the audio language
in the digital mode.
Switch the audio language.
When you pressSAP button on the remote control, the
currently selected language and the number of received
languages will be displayed on the screen.
Every time you press SAP button on the remote control,
the language will be switched.
Languages you can switch differ depending on the
receiving broadcast.
NOTE:
Pressing the SAPbutton works onlywith the someTV
channels, and doesnot work with external equipment such as
DVD players.
Volume adjustment
15
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

You can display the currently selected channel number or
other information such as the audio mode on the screen
for checking.
In the analog mode, the currently selected channel
number and the audio mode are displayed.
1 Display the channel number and the audio mode.
Press INFO button on the remote control.
The currently selected channel number and the audio
mode are displayed at the top right of the screen.
To clear the display, press INFO button again.
In the digitalmode, the detailed information for the
currently selected channel such as the program
guide is displayed.
1 Display the detailed information for the channel.
Every time you press INFO button, the display mode
will be switched as below.
The following information is displayedin the INFOmode.
(1) Program airtime
(2) Channel number
(3) Closed caption
(4) Channel title
(5) Audiolanguage
(6) Program content
NOTES:
When the programguide is displayedin more than6 lines, use VOL+/-
button and scroll forreading.
"No description provided"is displayed whenthe program guideis not
provided.
Screen information
13
AUTO
14.1
DTV-AIR
ENCODE 17:00-18:30
INFORMATION
America Masters 9.2
ENGLISH 1/3 CC
Satchmo: The Life of Lauis
Armstrong A self-taught
1
2
3
4
5
6
16
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

Video menu
1Press MENU button. The main menu screen will appear.
2 Press VOL+/- button to
select VIDEO Option,
then press CH- button
to enter.
3 Press CH+/- to select the desired option, then press
VOL+/- to adjust.
SETTING VIDEO
17
0101
CONTRAST 80
BRIGHTNESS 80
COLOR 50
SHARPNESS 50
TINT 0
VIDEO
Contrast
This will adjustthe intensity ofbright parts inthe picture but keep
the dark partsunchanged.
Brightness
This will adjustthe light outputof the completepicture, which will
mainly affect the darker areas of the picture.
Color
This will adjustthe saturation levelof the colorsto suit your
personal preference.
Sharpness
This will adjustthe sharpness offine details inthe picture.
Tint
Allows you toselect the colormix (Tint) of the picture.
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

Audio menu
1Press MENU button. The main menu screen will appear.
2 Press VOL+/- button to
select AUDIO Option,
then press CH- button
to enter.
3 Press CH+/- to select
the desired option, then
press VOL+/- to adjust.
SETTING AUDIO
18
0101
VOLUME 20
AUDIO
Volume
This will adjustthe sound outputlevel.
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0

Manual time setting
You must set the time manually
for ON/OFF Timer.
After apower failure ordisconnection of thepower,the
time will getlost. In thiscase, reset thepreset time.
NOTE:
EXAMPLE: Setting the time to "8:30AM"
TO SET TIME
1Press MENU. The main menu screen will appear.
2 Press VOL+/- button to
select TIME option,
then press CH- button
to enter the submenu.
3 Press CH+/- button to
select TIME, then press
CH+/- button to select
"--:--","AM";
press VOL+/- button to
set the value.
4 Press MENU until the MENUscreen disappears.
19
0101
TIME --:-- AM
TIMER OFF --:--AM
TIMER ON --:--AM
TIME
MUTE
Q.VIEW INFO
INPUT TV/DTV
SAP P.MODE
OK -
MENU
CH-
CH+
VOL
-
VOL
+
CC SLEEP S.MODE
GUIDE ARC CH.LIST
EXIT
123
456
789
0