Mendini 3-Piece Junior Drum Kit User manual
3-Piece Junior Drum Kit Assembly
Instrucon
3-Piece Junior Drum Kit Assembly Instrucon
Thank you for choosing this quality set from Cecilio. Use these instrucons as a guide to help you as-
semble your new drum set. There are many parts that make up a drum set, but don’t worry. Once you
get started, the process is very intuive and fun.
Bass Drum:
1. Lay the Bass Drum Shell (A) on a at surface (preferably carpeted) with the front side up. You
can idenfy the front side by the locaon of the Bass Drum spur mount (B). The spur mounts
are closer to the front side of the bass drum (furthest from the playing posion).
2. The logo drumhead should be ed to the front of the bass drum and centered with the tom
and cymbal mounts that are on the top of the shell.
3. Place the drumhead (C) (same diameter as the drum) directly on the top of the drum shell fol-
lowed by the rim. Make note to use the rim that does not have the bass drum pedal mount tab
(D). Align the holes on the rim with the lugs.
4. Slip a washer on each tension rods (E) and insert the tension rods through the holes in the rim.
5. Tighten the screws into the lugs using your ngers two at a me (opposite each other, just
enough so the hoops are secure and there are no wrinkles are in the head.
6. Now, use the drum key (F) to ghten the tension bolts in equal amounts (1/4 turn each for ex-
ample) unl pitch and tone of the drum begin to sound. The tension bolts should be ghtened
in a star formaon the same as when you change a wheel in a car (ghten the rst bolt, then
opposite bolt, etc).
7. Repeat this process on the back of bass drum. Remember, the back (player’s side) rim has the
bass drum pedal mount tab. This tab must be on the boom of the drum.
8. Insert the drum spurs (G) into the spur mounts and secure. Sit the drum upright and adjust the
height so that the front of the Bass Drum is elevated ½ to 1 inch o the oor. Be sure that the
bass drum spurs are secured and even.
9. To aach the bass drum pedal (H), place the pedal base under the tab on the player’s side bass
drum hoop. Align the holes and insert the small key screw (I) into the hole. Tighten so that it is
rmly aached to the tab.
10. Insert the felt bass drum beater (J) and adjust so that the beater strikes just below the center
of the bass drum head (C). Tighten with the drum key.
Tom Mounng:
11. Place the longer end of one of the L-Arms (K) into the center mount (L) on the bass drum – this
will adjust the height.
12. Slide the shorter end into the mount on the tom (M). Secure when in place.
Snare Drum Mounng:
13. Place the shorter end of the second L-Arm (N) into the mount (O) closest to the player on the
bass drum – this will adjust the height.
14. Slide the longer end into the mount on the snare (P). Secure when in place.
Cymbal Mounng:
15. Locate the cymbal arm (Q). Insert into the cymbal mount (R) on the bass drum with the
threaded secon furthest from the player and secure. Unscrew cymbal topper (S) and one felt.
16. Place the cymbal (T) on the stand with one felt below the cymbal. Replace the top felt and
cymbal topper. Please note that the topper does not need to be screwed down ght on the felt
and cymbal. The cymbal should be free to move during play. Its main operaon is to prevent
the cymbal from falling o the stand when struck.
Drum Throne, AKA Stool:
15. Open the drum throne base (U) so that the three legs are extended fully. Insert the seat post
into the block underneath the throne top (V) and secure. Adjust sing height and secure.
16. Once seated, you can now bring the set together and fully adjust any heights and angles of the
drums, cymbal and stands to your liking. Feel free to experiment. Enjoy!
3-Piece Junior Drum Kit Assembly Instrucon
Thank you for choosing this quality set from Cecilio. Use these instrucons as a guide to help you as-
semble your new drum set. There are many parts that make up a drum set, but don’t worry. Once you
get started, the process is very intuive and fun.
Bass Drum:
1. Lay the Bass Drum Shell (A) on a at surface (preferably carpeted) with the front side up. You
can idenfy the front side by the locaon of the Bass Drum spur mount (B). The spur mounts
are closer to the front side of the bass drum (furthest from the playing posion).
2. The logo drumhead should be ed to the front of the bass drum and centered with the tom
and cymbal mounts that are on the top of the shell.
3. Place the drumhead (C) (same diameter as the drum) directly on the top of the drum shell fol-
lowed by the rim. Make note to use the rim that does not have the bass drum pedal mount tab
(D). Align the holes on the rim with the lugs.
4. Slip a washer on each tension rods (E) and insert the tension rods through the holes in the rim.
5. Tighten the screws into the lugs using your ngers two at a me (opposite each other, just
enough so the hoops are secure and there are no wrinkles are in the head.
6. Now, use the drum key (F) to ghten the tension bolts in equal amounts (1/4 turn each for ex-
ample) unl pitch and tone of the drum begin to sound. The tension bolts should be ghtened
in a star formaon the same as when you change a wheel in a car (ghten the rst bolt, then
opposite bolt, etc).
7. Repeat this process on the back of bass drum. Remember, the back (player’s side) rim has the
bass drum pedal mount tab. This tab must be on the boom of the drum.
8. Insert the drum spurs (G) into the spur mounts and secure. Sit the drum upright and adjust the
height so that the front of the Bass Drum is elevated ½ to 1 inch o the oor. Be sure that the
bass drum spurs are secured and even.
9. To aach the bass drum pedal (H), place the pedal base under the tab on the player’s side bass
drum hoop. Align the holes and insert the small key screw (I) into the hole. Tighten so that it is
rmly aached to the tab.
10. Insert the felt bass drum beater (J) and adjust so that the beater strikes just below the center
of the bass drum head (C). Tighten with the drum key.
Tom Mounng:
11. Place the longer end of one of the L-Arms (K) into the center mount (L) on the bass drum – this
will adjust the height.
12. Slide the shorter end into the mount on the tom (M). Secure when in place.
Snare Drum Mounng:
13. Place the shorter end of the second L-Arm (N) into the mount (O) closest to the player on the
bass drum – this will adjust the height.
14. Slide the longer end into the mount on the snare (P). Secure when in place.
Cymbal Mounng:
15. Locate the cymbal arm (Q). Insert into the cymbal mount (R) on the bass drum with the
threaded secon furthest from the player and secure. Unscrew cymbal topper (S) and one felt.
16. Place the cymbal (T) on the stand with one felt below the cymbal. Replace the top felt and
cymbal topper. Please note that the topper does not need to be screwed down ght on the felt
and cymbal. The cymbal should be free to move during play. Its main operaon is to prevent
the cymbal from falling o the stand when struck.
Drum Throne, AKA Stool:
15. Open the drum throne base (U) so that the three legs are extended fully. Insert the seat post
into the block underneath the throne top (V) and secure. Adjust sing height and secure.
16. Once seated, you can now bring the set together and fully adjust any heights and angles of the
drums, cymbal and stands to your liking. Feel free to experiment. Enjoy!
Other manuals for 3-Piece Junior Drum Kit
1
Table of contents
Other Mendini Drum manuals
