MerlynBath Screens MB8 User manual

Installation Guide
MB8 Hinged Bath Screen
Any parts missing or damaged must be reported to your supplier within 5 days of purchase.
Inspect shower enclosure before fitting .No claims will be acceptable after product has been installed.
DO NOT attempt to install the product unless you can
tick ALL 4 boxes as satisfactory.
The wall plugs supplied with the installation kit are for
use in solid walls. Hollow or 'stud-partition’ walls will
require alternative fixings. Please consult a hardware
supplier for the correct type.
It may also be necessary to consult your tiling supplier
about the correct method for drilling your tiles.
USE SAFETY EYEWEAR WHEN DRILLING
Please familiarise yourself with the fitting
instructions before commencing fitting.
1. Check that you have the tools required.
2. Check that the installation site is compatible
with size of screen supplied
3. Check all the screen components.
4. Check that the installation kit is complete
Important
M
MERLYN
SHOWERING
MerlynBath
Screens.

COMPONENTS AND BOX CONTENTS
7
9
QTY Part No.
1
3
2
1
2
1
8
Description
Cover cap for wall profile L/R
B08070
M7009
M7016
M7006
M7008
M7012
Flat head screw ST4x30
Screw ST4x12
∅6 x 30 wall plug
Wall profile
No.
1
2
3
4
6
5
2
1
1
1
3
QTY Part No.
Description
No.
Plastic part for cover strip
10
11
12
13
14
15
Bottom seal
Moving panel
Vertical magnet seal
3
Moving panel
Cover cap for hinge
M7004
A2403001
2YS51
FIXING KIT COMPONENTS, TOOLS REQUIRED, SITE
x1
M7008
Tools Required
- 6mm masonry drill bit
- Power drill
- Quality Silicone
- Pencil
- Tape Measure
- #2 Philips Head screw driver
- Spirit level with horizontal and vertical level indicators
Spanner
-
IMPORTANT - Installation site
1. Ensure your bath is level before fitting. This screen is not designed
to fit on baths with stepped fronts, roll top rims or integral soap dishes.
2. The tiling or other wall finishing should be effectively sealed at the tray edges.
Fixing Kit components
pats shown are not to scale
Cover strip
816
3
Luna rail end cap L/R 2M7010L/R
M7014
Luna rail
AB
Part No.
M7017
M7013
Hinge(in side)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3.0mm
4x30
2YS51
x3
4x12
A2401201
x3
B08070
x3
B08092
x1
x2
M7012
x8 B08068
X1
M7010L/R
x2
M7017
M7020
X1
x2
M7016
x1
M7014

INSTALLATION
1.Position the wall profile so the seal on the
moving panel sits on the inside edge of the
bath. Fig 1.
2. Plumb the wall profiles using the vertical element of
the spirit level. Mark 3 holes, drill with 6mm masonry
bit and fit wall plugs. Using the 3 screw fix wall profile
to wall. Fig 2.
FIG 1
screen
inside
bath edge
3. Ensure rising butt (Fig3/C) is to the bottom ,if not reverse. by loosening
screws as in A,B,C. And switch top and bottom as D,E,F. Fig3
FIG 2
LH RH
A
C
B D F
E
FIG 3

4. Insert the screen into the wall profile. Ensure the bottom edge
of the moving panel is parallel to the top surface of the bath.
Use spacer (M7020) to position. Fig4.
5. Drill 3 holes through the wall profile and
fixed panel using a 3.0mm steel drill
Using the screw , fix the bit.(B08092)
to the wall profile in 3 screen upright profile
places. Fig 5.
6. Attach the cover strip to the wall profile. Starting
at the bottom firmly press cover strip into place
and gradually work from bottom to top Fig 6.
FIG 5 FIG 6
INSIDE
M7020
FIG 4A FIG 4B
INSIDE
M7020
INSIDE

8. Position moving panel at 90 degrees
to the fixed panel. Starting at the bottom
push on magnet seals fully. Open the moving
panel and ensure both seals meet fully and
provide a complete seal. If there is a gap push
both seals together. Fig 8.
7. Fix top cover cap(M7017) to wall
profile (M7013). Fig 7.
10. Fix the bottom seal. Fig 10.
9. Fix the cover caps (M7012) to both hinge. Fig 9.
IMPORTANT: Ensure bottom seal is tight to bath top
surface along the screen. Keep defector fin to inside.
FIG 9
FIG 10
M7016
FIG 7
FIG 8
Add a dab of silicone to
the top of each end.
Notch the bottom
fin 3mm to ensure
a tight fit to the
bottom bracket.
Silicone
3
Silicone

FIG 12
12. Sealing. Fig 12.
Inside(dashed line):
When installation is complete seal the joint between the wall
profile and the wall, top to bottom on the inside only.
SEAL where the wall profile and fixed panel sit on the bath.
Outside(full line)
From outside the screen, Seal along the bottom where the fixed
panel,frame and wall profile meet the bath.Seal 50mm up where
the frame meets the wall profile and where the wall profile meets
Visit our website, www.merlynshowering.com
11.Fitting the luna rail is optional.If fitted
the luna rail as they will get damaged.Fix the luna rail on top of bath. Put a dab of
silicone to bottom of each luna rail end cap (note left & right) and a thin bead of silicone
to the bottom of the luna rail. Fit cap to end of fixed panel and carefully place luna rail
into end cap. Ensure the luna rail is parallel to the bath edge. Fig 11.
the panels cannot be folded out over
OPTIONAL
FIG 11
Silicone
Silicone