Metabo HPT SuperDrive 75 Series User manual

SAFETY NOTES:
1. Make sure the SuperDrive 75 tool is powered down and
unplugged before replacing a bit, or removing the indexing unit.
2. Never use SuperDrive 75 while standing on an unstable platform.
3. Never point the driver at yourself or others in the work area.
4. Avoid wearing loose clothing, jewelry or other items that could
become caught in the tool.
5. Make sure SuperDrive 75 is clear of clothing, hair or other loose
items while operating the tool.
6. Make sure the tool is powered down and unplugged before
performing any adjustment or repair to the indexing module.
7. Always use collated screws and strips that are designed for this tool.
See Technical Data below.
OPERATING SuperDrive 75
Attaching the indexing Module
1. Remove the factory nose piece and bit from
the driver.
2. Remove the bit holder from the driver.
3. Attach SuperDrive 75 coupler to the Hitachi
driver. (A,B)
4. Insert SuperDrive bit tip into the screw gun.
(A,B)
TECHNICAL DATA:
1. Use SuperDrive 75 with #6-#12 gauge screws only.
2. Use SuperDrive 75 with screw lengths from 5/8-in (16mm) - 3-in
(76mm) only.
3. SuperDrive 75 is designed for fastener head diameters up to
3/8-in.
4. Only use bits with a 6mm shank diameter with SuperDrive 75.
5. SuperDrive 75 is designed to work best with the following bits:
725449 - 178mm Square
725438 - 178mm Phillips
725439 - 178mm LOX
®
®
®
®
®
®
®
®
®
Operating Instructions for SuperDrive®75
1. Remove factory nose piece 2. Remove bit holder and bit
3. Attach SuperDrive 75 coupler
4. Insert SuperDrive bit tip into the screw gun
(A)
(A)
(B)
(B)

OPERATING SuperDrive 75
5. Slide the SuperDrive 75 indexing module
onto the coupler and tighten the locking
wing nut clockwise.
OPERATING SuperDrive 75
Attaching the extension
1. Remove the factory nose piece and bit from
the driver and install the SuperDrive 75
coupler as described in the instructions 1-3
(Attaching the indexing module) above.
2. Slide the SuperDrive handle onto the
coupler. Rotate the handle to the desired
position. Then rotate the grip clockwise
securing it into position.
3. Fit the bit rod extension into the driver.
6. Insert a collated strip of screws into the
indexing module guiding the strip through
the feed track and into the indexing guide.
7. Position the first screw in the strip in the
center of the bit tip guide.
1. Remove factory nose piece and install the SuperDrive coupler
2. Install the handle
3. Install the bit rod extension
5. Attach the SuperDrive indexing module
6. Insert collated strip into the indexing module
7. Position the first screw

SUGGESTIONS FOR OPERATION:
For best results position SuperDrive 75 at a right angle to the work
surface as much as is possible. Allow the driver to fully spin up
before pressing SuperDrive 75 to the sub-strait surface. Press
SuperDrive 75 to the sub-strait maintaining even and consistent
pressure until the fastener is fully driven in. Check fastener depth
and make any necessary fine adjustment. Keep the driver fully spun
up as subsequent screws are driven.
Check to see that the Metabo HPT driver is in the right (R) or forward
position before operating the tool.
4. Attach the SuperDrive extension tube to the
coupler. Rotate the extension tube counter
clockwise screwing it onto the coupler.
5. Insert the SuperDrive bit tip into the bit
holder.
6. Attach the SuperDrive 75 indexing module
to the extension tube and tighten the wing-
nut securing it to the extension tube.
ADJUSTING FOR FASTENER LENGTH(Coarse adjustment)
1. Loosen the Phillips set screw on the nose piece by rotating it
counter clockwise.
FINE DEPTH ADJUSTMENT
Twist the knurled wheel at the top of the SuperDrive 75 indexing
module to make fine depth adjustment. An adjustment scale and
guide are located on the top of the tool.
2. Move the nose piece in or out as needed to match
fastener length.
3. Tighten the set screw back down turning it clockwise to secure
the nose piece in place for operation.
4. Attach the extension tube to the coupler
5. Install the SuperDrive bit tip
6. Attach the SuperDrive 75 indexing module
R

®
®
®
®
®
®
®
®
®
Metabo HPT SuperDrive Auto-feed Screw System
WARRANTY
Metabo HPT SuperDrive tools and system components are warranted to the original retail purchaser to be free from defects
in material and workmanship one year from the date of purchase. A dated sales receipt or proof of purchase is required to
make a warranty claim.
The warranty shall only cover defects in material or workmanship. The warranty shall not cover normal wear items or issues
arising from improper use, as determined by Koki Holdings America Ltd. in its absolute discretion.
Koki Holdings America Ltd. is not responsibility for malfunctions, failures or defects resulting from misuse, abuse, neglect,
alteration, or modification of the Metabo HPT SuperDrive tool and system components. Koki Holdings America Ltd. disclaims
any warranty regarding fitness for any particular use or application of its tools or fasteners. No other warranties,
representations or promises as to the quality or performance of the Metabo HPT SuperDrive fastening tool and system
components are made, other than those contained herein.
ANY IMPLIED WARRANTY GRANTED UNDER STATE LAW, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO DURATION OF THE EXPRESS WARRANTY GRANTED HEREIN. KOKI HOLDINGS
AMERICA LTD. SHALL NOT BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES. SOME
STATES DO NOT ALLOW FOR EXCLUSIONS OR LIMITATIONS OF DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY.