Meters music LINX User manual

METERS LINX
USER GUIDE

Important Safety Information
Please read the Meters user manual and keep safe for future reference.
Meters are designed for responsible listening. To enjoy the maximum pleasure
from your Meters headphones here are some DOSand DON’TS.
DON’T use the headphones at a high volume for any extended period. High
volume for long periods means you will only be able to enjoy Meters for a short
period. No fun in that!
- To avoid hearing impairment, use your headphones at a comfortable,
moderate volume level.
- Always turn the volume down on your Meters before placing the headphones
on your ears, gradually turning up the volume until you reach a comfortable
listening level.
DO focus on your safety and always be aware of what is going on around you.
Please pay particular attention when using Meters while engaging in any activity
such as riding a bicycle or running or walking in or near traffic, a building site or
railroad, etc.
DON’T use your headphones while driving or at any time when the inability to
hear outside surrounding sounds may present a danger to yourself or others.
DO be aware of the temperatures and humidity when using Meters headphones.
Operate or store in a place where the temperature is between -15˚C ( 5˚F ) and
55˚C (131˚F) (up to 90% relative humidity).
DON’T submerge or expose for extended period to water, or wear while
participating in water sports, i.e. swimming, water-skiing, surfing, etc. Exposure
to moisture may increase the risk of fire or electric shock.
DON’T use the headphones as aviation communication headsets except in
case of emergency.
DON’T place naked flame sources, such as lighted candles, near your Meters
headphones.
DON’T make any unauthorised alterations to your Meters. Doing so will void the
warranty, compromise safety, and affect regulatory compliance and system
performance.
Remember Meters are THE only headphones that move to your music and our
exclusive technology and innovation allows you, the user, a greater appreciation
of the finer details of your favourite music at lower volumes.
DO enjoy your Meters Headphones at ALL times!

Speaker Specifications
Type: True Wireless
Audio Chip: QualcommQCC3020
Transmission range: 10M
Frequency Response: 40HZ-20KHZ
Waterproof: IPX5
Weight: 132gs (0.29lbs)
Charge Connection: USB-C
Charging time: 1 Hour
Music playback: 3 Hours
Battery Capacity: 600 mAh
Bluetooth®Specification Version: 5.0
Supports Bluetooth®Codec : SBC, apt-X,
apt-X HD. Supports HSP, HFP, A2DP, AVRCP
profile Supports voice prompt
Disposal of Old Electrical Equipment (Applicable in the European Union and other
European countries with separate collection systems).
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the appropriate collection
point for the recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources.
For more detailed info about recycling this product, please contact your local Council, your
household waste disposal service or the shop where you purchased the product.
Notice for customer: the following information is only applicable to equipment sold
in countries applying EU directives
For more information head to:
www.metersmusic.com
Manufacturer: Meters Music Ltd. The Old Maltings, Hall Road, Heybridge, Essex, England, CM9 4NJ.
Ear Bud Specifications
Type: True Wireless
Audio Chip: QualcommQCC3020
Transmission range: 10M
Frequency Response: 2.4GHZ-2.48GHZ
Waterproof: IPX5
Charging Case Weight: 111gs (0.24lbs)
Earbud Weight (each): 5.9gs (0.01lbs)
Charge Connection: USB-C
Charging time: 1 Hour
Talk time: 6 Hours
Music playback: 6 Hours
Battery Capacity: 600 mAh
Bluetooth®Specification Version: 5.0
Supports Bluetooth®Codec : SBC, apt-X,
apt-X HD. Supports HSP, HFP, A2DP, AVRCP
profile Supports voice prompt

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
. Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications
not expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment. (Example - use only shielded
interface cables when connecting to computer or peripheral devices).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
TWS Earbud Controls
Power On:
To power on the earbuds simply open the charging case and remove the
earbuds, they will automatically power on.
If your earbuds are out of the case and powered down (after 5 mins of no use,
they auto power down) you can simply touch both earbuds for 1 second to
power them up.
Power Off:
Simply put your earbuds back into the charging case and close the lid to
power off.
If no device is connected for 5 minutes the earbuds will auto power off.
You can also long press both earbuds together for 5 seconds to power off.
Pairing:
When the charging case is opened the earbuds automatically go into pairing
mode. Go to your devices Bluetooth® menu and choose the earbuds from
the list, they will be named ‘Meters Linx’. Once connected to your device every
time you open the charging case, they will automatically pair with your existing
device. If the existing device isn’t found after 10 seconds the earbuds will go
back into pairing mode.
Disconnect:
If you wish to disconnect your earbuds from your current paired device, you can
long press and hold both earbuds at the same time for 3 seconds.

Music Controls:
Play/Pause: Short press either the Left or Right earbud.
Next Track: Hold the Right earbud.
Previous Track: Hold the Left earbud.
Volume Up: Double touch the Right earbud.
Volume Down: Double touch the Left earbud.
Phone Controls:
Accept a call: When you receive a call short press either the Left or Right earbud.
Reject a call: When you receive a call long press either the Left or Right earbud.
End a call: Whilst in a call short press either the Left or Right earbud.
Volume Up: Hold the Right earbud.
Volume Down: Hold the Left earbud.
Voice assistant:
Triple touch the Right earbud to activate your voice assistant, e.g., Siri or Google
assistant.
Low Battery:
When battery gets low and needs charging you will hear “Battery Low” in the
earbuds. Place earbuds into the charging case to charge.
Charging Case:
Use the included USB Type C cable to charge the case with a 12v USB charging
outlet (not supplied). Whilst connected to power the 4 LED lights (see fig 2.) in
the case will light up to show the current state of charging, first light = 25% charge,
second light = 50% charge, third light = 75% charge, fourth light = Fully charged.
Charging the Earbuds:
Place the earbuds into the charging case to charge, you will see a solid Red light
on the earbuds to indicate they are charging. Once fully charged the Red LED
light will turn off.
Reset:
If you need to reset the earbuds remove the earbuds from the charging case
and make sure they are powered off. Long press the Left & Right earbuds at the
same time for 10 seconds.
FIG 2. TWS CHARGING CASE OPEN
Left earbud housing Right earbud housing
LED charge indicator

TWS Speaker Controls
Power On:
To power on long press the power button (see fig 1.) for 3 seconds, Blue LED will
light up to indicate power.
Power Off:
Long press power button (see fig 1.) for 3 seconds.
Pairing:
Press the Bluetooth® button (see fig 1.), LED will flash Red & Blue to indicate
pairing mode.
Go to your devices Bluetooth® menu and choose the speakers from the list,
they will be named ‘Meters Linx Spk’.
Disconnect:
If you wish to disconnect your speakers from your current paired device, you
can long press and hold the Bluetooth® button (see fig 1.), for 10 seconds.
Music Controls:
Play/Pause: Short press Play/Pause Button (see fig 1.).
Next Track: Long press Volume Up Button (see fig 1.).
Previous Track: Long press Volume Down Button (see fig 1.).
Volume Up: Short press Volume Up Button (see fig 1.).
Volume Down: Short press Volume Down Button (see fig 1.).
Phone Controls:
Accept a call: When you receive a call short press Play/Pause Button (see fig 1.).
Reject a call: When you receive a call long press Play/Pause Button (see fig 1.).
End a call: Whilst in a call short press Play/Pause Button (see fig 1.).
Voice assistant:
Double click Play/Pause Button (see fig 1.). to activate your voice assistant, e.g.,
Siri or Google assistant.
FIG 1. TWS SPEAKER TOP
Bluetooth® button Power button
Volume Up/Track
back button
Volume Down/Track
forward button

Charging Speaker:
Use the included USB Type C cable to charge the case with a 12v USB charging
outlet (not supplied). Whilst connected to power the LED lights on the speaker
will light up to show the current state of charging, see below.
1. LED solid Red whilst charging.
2. LED off when fully charged.
TWS Earbud/Speaker System Controls
If you are using the Linx Earbuds & Speakers System (Both earbuds & speakers)
there is no need to pair up your speakers separately (unless you just want to use
them on their own). Once paired to your earbuds you can just put your earbuds
in the charging case, leave the lid open and the speakers will connect and
continue playing your music you were listening to on your earbuds!
The speakers and earbuds once paired can be controlled in the same way as the
above instructions.
Notes:

www.metersmusic.com