Metra Electronics WM-BPLTC User manual

IMPORTANT
If you are having difficulties with the installation ofthis
product, please call out Tech Support line at386-257-1187.
Before doing so, looks over the instructions a second time,
and make sure the installation wasperformed exactly asthe
instructions are stated. Please have the vehicle apart and
ready to perform troubleshooting steps before calling.
WM-BPLTC
Product Manual
WM-BPLTC
Product Manual
386-257-1187
Metra Electronics
460 Walker Street, Holly Hill, FL 32117
IMPORTANT
If you are having difficulties with the installation ofthis
product, please call out Tech Support line at386-257-1187.
Before doing so, looks over the instructions a second time,
and make sure the installation wasperformed exactly asthe
instructions are stated. Please have the vehicle apart and
ready to perform troubleshooting steps before calling.
386-257-1187
Metra Electronics
460 Walker Street, Holly Hill, FL 32117
REV 10/18/2019
Rev. 2/20

I. Specifications
I. Specifications
II. Connections
1. Begin by removing the license plate bolts and the license plate,
then install the camera. Replace plate and bolts.
2. Connect the RED wire to the +12 volt reverse wire.
NOTE: If not connected to the reverse signal in the vehicle, the
LEDs will be on at all times. LEDs turn on with camera power.
3. Connect the BLACK wire to ground (a metal, non-painted surface).
4. Run the video cable through the vehicle, up to the video display.
(Avoid placing video cable where it can get pinched or damaged)
5. Attach the YELLOW video RCA to the reverse camera input on the
display. If reverse signal was connected in the rear of the vehicle,
there is a red wire on the yellow RCA to provide the same +12 volt
signal to the display if needed. If not needed please tape up as 12
volts is present when vehicle is in reverse and can damage the
camera if this wire touches ground.
NOTE: The camera needs to be angled down 30-40 degrees for proper
functionality. This may inhibit the use of a license plate frame around the
plate.
II. Connections
1. Begin by removing the license plate bolts and the license plate,
then install the camera. Replace plate and bolts.
2. Connect the RED wire to the +12 volt reverse wire.
NOTE: If not connected to the reverse signal in the vehicle, the
LEDs will be on at all times. LEDs turn on with camera power.
3. Connect the BLACK wire to ground (a metal, non-painted surface).
4. Run the video cable through the vehicle, up to the video display.
(Avoid placing video cable where it can get pinched or damaged)
5. Attach the YELLOW video RCA to the reverse camera input on the
display. If reverse signal was connected in the rear of the vehicle,
there is a red wire on the yellow RCA to provide the same +12 volt
signal to the display if needed. If not needed please tape up as 12
volts is present when vehicle is in reverse and can damage the
camera if this wire touches ground.
NOTE: The camera needs to be angled down 30-40 degrees for proper
functionality. This may inhibit the use of a license plate frame around the
plate.
Sensor
1/3” CMOS FPX8341
Effective Pixel
720 X 480
Video Signal
NTSC 60hz
Dynamic Guidance
Trajectory
Embedded
Resolution
600 TV Lines
Current Consumption
No more than 180mA
Power Supply
DC 9V-12V
Operating Temperature
-20ºC - 70ºC
Storage Temperature
-30ºC - 80ºC
View Angle
Horizontal: 100, Vertical: 110.
Diag. 140
Water Resistance
IP68
Minimum Illumination
0.1 Lux
LED LUX
30 Lux
Sensor
1/3” CMOS FPX8341
Effective Pixel
720 X 480
Video Signal
NTSC 60hz
Dynamic Guidance
Trajectory
Embedded
Resolution
600 TV Lines
Current Consumption
No more than 180mA
Power Supply
DC 9V-12V
Operating Temperature
-20ºC - 70ºC
Storage Temperature
-30ºC - 80ºC
View Angle
Horizontal: 100, Vertical: 110.
Diag. 140
Water Resistance
IP68
Minimum Illumination
0.1 Lux
LED LUX
30 Lux
The RED 12v trigger can also be
used as camera power when
connected to a 12v source.
GND
12v
PWR
Extension cable Camera cable
20 ft 6 ft
The RED 12v trigger can also be
used as camera power when
connected to a 12v source.
GND
12v
PWR
Extension cable Camera cable
20 ft 6 ft
II. Connections