Metric A Series Operation manual

308–471
Rev. B
Supersedes A

INSTRUCTIONS-PARTS LIST
INSTRUCTIONS
This manual contains important
warnings and information.
READ AND KEEP IT FOR REFERENCE.
19 LITER (5 GALLON) SIZE, 31:1 RA TIO BULLDOG 
Ram-Mounted Pump
WITH CHECK-MA TE800 DISPLACEMENT PUMP
214 bar, 21.4 MPa (3100 psi) Maximum Fluid Working Pressure
7 bar, 0.7 MPa (100 psi) Maximum Pump Air Inlet Pressure
10 bar, 1.0 MPa (150 psi) Maximum Air Inlet Pressure
Part No. 237–263 Pump, Series A
31:1 Ratio Pump, with Bulldog  Air Motor
Refer to page 2 for T able of Contents.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
COPYRIGHT 1995, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001

 
Table of Contents
Warnings 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setup 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Graco W arranty and Disclaimers 16. . . . . . . . . . . . . . . .
Toll-Free Graco Phone Numbers 16. . . . . . . . . . . . . . . .
Symbols
Warning Symbol
WARNING
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
Caution Symbol
CAUTION
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
INSTRUCTIONS
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury .
 This equipment is for professional use only .

Read all instruction manuals, tags, and labels before operating the equipment.
 Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor .
 Do not alter or modify this equipment.
 Check equipment daily . Repair or replace worn or damaged parts immediately .

Do not exceed the maximum working pressure stated on the equipment or in the T echnical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
 Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer ’ s warnings.
W ear hearing protection when operating this equipment.
 Comply with all applicable local, state, and national fire, electrical, and safety regulations.

 
WARNING
INJECTION HAZARD
Spray from the spray gun/dispense valve, leaks or ruptured components can inject fluid into your body
and cause extremely serious injury , including the need for amputation. Fluid splashed in the eyes or on
the skin can also cause serious injury .

Fluid injected into the skin might look like just a cut, but it is a serious injury . Get immediate medi -
cal attention.

Do not point the gun/valve at anyone or at any part of the body .
 Do not put your hand or fingers over the spray tip/nozzle.
 Do not stop or deflect leaks with your hand, body , glove or rag.
 Do not “blow back” fluid; this is not an air spray system.
 Always have the tip guard and the trigger guard on the gun when spraying.
 Check the gun dif fuser operation weekly . Refer to the gun manual.
 Be sure the gun/valve trigger safety operates before spraying.
 Lock the gun/valve trigger safety when you stop spraying.
 Follow the Pressure Relief Procedure on page 9 if the spray tip/nozzle clogs and before clean -
ing, checking or servicing the equipment.
T ighten all fluid connections before operating the equipment.
 Check the hoses, tubes, and couplings daily . Replace worn or damaged parts immediately . Do not
repair high pressure couplings; you must replace the entire hose.
 Use only Graco approved hoses. Do not remove the spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
MOVING P ARTS HAZARD
Moving parts, such as the priming piston and wiper plate, can pinch or amputate your fingers.
 Keep clear of all moving parts when starting or operating the pump.
 Keep hands and fingers away from the priming piston during operation and whenever the pump is
charged with air .

Keep your hands away from the wiper plate and the lip of the pail while the ram is operating.
 Before servicing the equipment, follow the Pressure Relief Procedure on page 9 to prevent the
equipment from starting unexpectedly.

 
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury
.
 Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
 If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing/dispensing immediately . Do not use the equipment until you identify and correct the problem.
 Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed/dispensed.
 Keep the spray/dispense area free of debris, including solvent, rags, and gasoline.
 Electrically disconnect all equipment in the spray/dispense area.
 Extinguish all open flames or pilot lights in the spray/dispense area.
 Do not smoke in the spray/dispense area.
 Do not turn on or of f any light switch in the spray/dispense area while operating or if fumes are
present.
 Do not operate a gasoline engine in the spray/dispense area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
 Know the specific hazards of the fluid you are using.
 Store hazardous fluid in an approved container . Dispose of hazardous fluid according to all local,
state and national guidelines.
 Always wear protective eyewear , gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer .

308-471 5
Setup
Grounding
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below . Also read
the section FIRE OR EXPLOSION HAZ -
ARD
on page 4.
1. Pump: use the ground wire and clamp (supplied).
See Fig. 1. Loosen the grounding lug locknut (W)
and washer (X). Insert one end of the ground wire
(Y) into the slot in lug (Z) and tighten the locknut
securely . Connect the other end of the wire to a
true earth ground.
Fig. 1
W
X
Y
Z

2. Air and fluid hoses: use only electrically conductive
hoses.
3.
Air compressor: follow manufacturer ’ s recommen -
dations.
4.
Spray gun/dispense valve: ground through connec -
tion to a properly grounded fluid hose and pump.
5. Fluid supply container: follow your local code.
6. Object being sprayed: follow your local code.
7. Solvent pails used when flushing: follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding continu -
ity.
8.
T o maintain grounding continuity when flushing or
relieving pressure , hold a metal part of the spray
gun/dispense valve firmly to the side of a grounded
metal pail, then trigger the gun/valve.

6 308-471
Setup
NOTE: Reference numbers and letters in parentheses
in the text refer to the callouts in the figures and the
parts drawing.
NOTE: Always use Genuine Graco Parts and Acces -
sories, available from your Graco distributor . If you
supply your own accessories, be sure they are ade -
quately sized and pressure rated for your system.
Fig. 2 is only a guide for selecting and installing sys -
tem components and accessories. Contact your Graco
distributor for assistance in designing a system to suit
your particular needs.
Supplied Components
Refer to Fig. 2.
WARNING
A red-handled main air bleed valve (E), pump air
bleed valve (H), and fluid drain valve (L) are sup -
plied. These accessories help reduce the risk of
serious injury
, including fluid injection and splashing
of fluid in the eyes or on the skin, and injury from
moving parts if you are adjusting or repairing the
pump.
The red-handled main air bleed valve (E) shuts of f
and relieves the air to the pump and ram. The ram
will hold pressure if the ram director valve (U) is in
the horizontal (neutral) position. T o relieve air
pressure in the ram, close the red-handled bleed
valve (E) and move the director valve (U) to
DOWN. The ram will slowly drop.
The pump air bleed valve (H) relieves air trapped
between it and the pump after the air is shut of f.
T
rapped air can cause the pump to cycle unexpect -
edly
. Locate the valve close to the pump.
The fluid drain valve assists in relieving fluid pres -
sure in the displacement pump, hose, and gun.
T riggering the gun to relieve pressure may not be
sufficient.
 The red-handled main air bleed valve (E) is
required in your system to shut of f the air supply to
the pump and ram (see the WARNING at left).
When closed, the valve will bleed of f all air in the
ram and pump, and the ram will slowly lower . Be
sure the valve is easily accessible from the pump,
and is located upstream from the air manifold (F).

The pump air bleed valve (H) is required in your
system to relieve air trapped between it and the air
motor when the valve is closed (see the WARNING
at left). Be sure the valve is easily accessible from
the pump, and is located downstream from the air
regulator (G).
The
air regulator (G) controls pump speed and
outlet pressure by adjusting the air pressure to the
pump. Locate the regulator close to the pump, but
upstream from the pump air bleed valve (H).
The air manifold (F) has a swivel air inlet. It
mounts to the ram, and provides ports for connect -
ing lines to air-powered accessories.
 The air relief valve (W) opens automatically to
prevent overpressurization of the pump.
 The ram air regulator (T) controls the air pressure
to the ram.
 The ram director valve (U) controls the raising
and lowering of the ram.
The air assist shutoff valve (V) opens and closes
the flow of air to assist raising the wiper plate (C)
out of an empty pail.


Fig. 2
KEY
APump
BRam
CWiper
Plate
D Electrically Conductive Air Supply Hose
E Red-Handled Main Air Bleed V alve
(required, for pump and ram)
F Air Manifold
G Pump Air Regulator
H Pump Air Bleed V alve
(required, for pump)
J Air Line Filter
KBleed-T ype Air V alve
(for accessories)
L Fluid Drain V alve (required)
M Fluid Pressure Regulator
N Electrically Conductive Fluid Hose
P Electrically Conductive Fluid Whip Hose
RGun/V alve Swivel
S Gun or Dispensing V alve
T
Ram Air Regulator
U Ram Director V alve
V
Air Assist Shutof f V alve
W
Air Relief V alve
Y
Ground Wire (required; see page 5
for installation instructions)
A
B
C
D
E
FG
H
JK
M
N
P
Y
MAIN AIR LINE
LR
S
T
TYPICAL INSTALLATION
U
V
W
 
Setup

 
Setup
Location
Position the ram so the air regulators for the pump and
the ram will be easily accessible. Ensure that there is
suf ficient overhead clearance when the ram is fully
raised. Refer to Dimensions on page 15.
Using the holes in the ram base as a guide, drill four
13 mm (1/2 in.) diameter holes for anchors.
Check that the ram base is level in all directions. If
necessary , level the base using metal shims. Secure
the base to the floor using 13 mm (1/2 in.) anchors
which are long enough to prevent the ram from tipping.
System Accessories
Refer to Fig. 2.
Air and Fluid Hoses
Be sure all air hoses (D) and fluid hoses (N, P) are
properly sized and pressure-rated for your system.
Use only electrically conductive hoses. Fluid hoses
must have spring guards on both ends. Use of a short
whip hose (P) and a swivel (R) between the main fluid
hose (N) and the gun/valve (S) allows freer gun/valve
movement.
Air Line Accessories
Install the following accessories in the locations shown
in Fig. 2, using adapters as necessary:
An air line filter (J) removes harmful dirt and
moisture from the compressed air supply .
A second
air bleed valve (K) isolates the air line
accessories for servicing. Locate upstream from all
other air line accessories.
Fluid Line Accessories
Install the following accessories in the locations shown
in Fig. 2, using adapters as necessary:
A fluid drain valve (L) is required in your system
to relieve fluid pressure in the hose and gun/valve
(see the WARNING on page 6). Screw the drain
valve into the open branch of a tee mounted in the
fluid line. Install the drain valve pointing down, but
so the handle will point up when opened.
A fluid regulator (M) controls fluid pressure to the
gun/valve, and dampens pressure surges.
 A gun or valve (S) dispenses the fluid. The gun
shown in Fig. 2 is a dispensing gun for highly
viscous fluids.
 A gun swivel (R) allows freer gun/valve move -
ment.

308-471 9
Operation
Pressure Relief Procedure
WARNING
INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally . Fluid
under high pressure can be injected through the
skin and cause serious injury . T o reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
 are instructed to relieve the pressure,
 stop spraying/dispensing,
 check or service any of the system equipment,
 or install or clean the spray tip/nozzle.
1. Lock the gun/valve trigger safety .
2.
Close the pump air bleed valve (H, required in your
system).
3. Shut of f the red-handled main air bleed valve (E,
required in your system). Set the ram director
valve (U) to DOWN. The ram will slowly drop.
4. Unlock the gun/valve trigger safety .
5.
Hold a metal part of the gun/valve firmly to the side
of a grounded metal pail, and trigger the gun/valve
to relieve pressure.
6. Lock the gun/valve trigger safety .
7.
Open the drain valve (required in your system)
and/or the pump bleeder valve (DD), having a
container ready to catch the drainage.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip/nozzle or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the tip guard retaining nut or hose end coupling
and relieve pressure gradually , then loosen completely .
Now clear the tip/nozzle or hose.
Starting and Adjusting the Ram
1. Refer to Fig. 3. Close all air regulators and air
valves.
2.
Open the red-handled main air bleed valve (E) and
set the ram air regulator (T) to 2.8 bar , 0.28 MPa
(40 psi). Pull up on the director valve (U) handle so
the arrow points to UP , and let the ram rise to its
full height.
3. Set a full 19 liter (5 gal.) pail of fluid on the ram
base, slide it back against the ram tube and sup -
ports, and center it under the wiper plate (C). T o
prevent air from being trapped under the wiper
plate, scoop fluid from the center of the pail to the
sides, to make the surface concave.
WARNING
MOVING P ARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the pump intake,
wiper plate, and lip of the fluid container .
4. With your hands away from the pail and the wiper
plate, push down on the director valve handle so
the arrow points to DOWN, and lower the ram until
the wiper plate rests on the lip of the pail. Move
the director valve handle to the horizontal position
(neutral).
5.
Adjust the pail to be sure it is aligned with the
wiper plate, and remove the vent handle (AA) from
the wiper plate (C) to open the vent hole (BB).
6. Set the director valve to DOWN and continue to
lower the ram until fluid appears at the wiper plate
vent hole (BB). Set the director valve to neutral,
reinstall the vent handle and tighten securely . See
Fig. 3.

 
Operation
Starting and Adjusting the Pump
1. Be sure the pump air regulator (G) is closed. Then
set the ram air regulator (T) to about 2.1 bar , 0.21
MPa (30 psi). Set the director valve (U) to DOWN.
See Fig. 3.
2. Start the pump as explained in the separate pump
instruction manual.
3. Keep the director valve (U) set to DOWN while the
pump is operating.
NOTE: Adjust the air pressure to the ram as needed,
but do not increase it to a level where fluid is forced
past the wiper plate (C).
Changing Fluid Pails
WARNING
MOVING P ARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the pump intake,
wiper plate, and lip of the fluid container .
1. Stop the pump. Close the pump air bleed valve
(H).
2.
Set the director valve (U) to UP .
3.
Open the air assist valve (V) and the petcock
(CC). Keep them open until the wiper plate clears
the top of the pail.
4. Remove the empty pail and place the full pail on
the ram base.
5. Close the air assist valve (V) and petcock (CC).
6. Lower the ram and adjust the position of the pail
relative to the wiper plate, as explained under
“Starting and Adjusting the Ram” on page 9.
Shutdown and Care of the Pump
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 9.
1. Relieve the pressure.
2. Follow the pump shutdown instructions in your
separate pump manual.

 
Operation
04409B
05094A
Fig. 3
E
KEY
APump
BRam
CWiper
Plate
E Red-Handled Main Air Bleed V alve
(required, for pump and ram)
G Pump Air Regulator
H Pump Air Bleed V alve
(required, for pump)
T Ram Air Regulator
U Ram Director V alve
V
Air Assist Shutof f V alve
AA
Wiper Plate V ent Handle
BB V ent Hole
CC Air Assist Petcock
DD Pump Bleeder V alve
A
B
C
G
H
T
U
V
AA
BB
CC
DD
05313A

05313A
05093A
1
5
6
7
2
2 (Ref)
8
9
10
4{
See Detail
at right
Y22
22Y
11
13
{14
15{
16{
{17
18{
19
20
21
See Detail
on page 13
25
23
24
 
Parts
Part No. 237–263, Series A
31:1 Ratio Bulldog Pump, with Check-Mate 800
Severe-Dutyt Carbon Steel Displacement Pump

 
Parts
Part No. 237–263, Series A
31:1 Ratio Bulldog Pump, with Check-Mate 800
Severe-Dutyt Carbon Steel Displacement Pump
Ref.
No. Part No. Description Qty. Ref. No. Part No. Description Qty.
1 237–261 PUMP
, Bulldog, 31:1 ratio;
See manual 308–351 for parts 1
2 237–561
RAM, 19 liter (5 gal.) size
See manual 306–838 for parts 1
4{206–197 AIR REGULATOR
See manual 308–168 for parts 1
5 156–172
SWIVEL; 3/4 npt(f) x 3/4 npsm(f) 1
6 113–218 AIR VAL
VE, bleed-type; red-handled
3/4 npt(m x f) 1
7 157–129
NIPPLE; 3/4 npt; 3.25 in. (82 mm) 1
8 109–123 HOSE, air assist 1
9 109–124 HOSE, ram air supply 1
10 155–541 ADAPTER, swivel, 90_;
1/4 npt(m) x 1/4 npsm(f) 1
11 237–569 GROUND WIRE AND CLAMP 1
12 206–994 THROAT SEAL LIQUID;
8 oz (0.5 liter); not shown 1
13 107–142 BLEED VAL
VE; 3/4 npt (m x f) 1
14{206–205
MANIFOLD, air; 3/4 npsm(f) 1
15{100–960 GAUGE, air 1
16{100–840 ELBOW
, street; 90 _ ; 1/4 npt (m x f) 1
17{100–509
PLUG, pipe, sq hd; 1/4 npt 2
18{100–403
PLUG, pipe; 1/8 npt 1
19 238–033
HOSE, air; 3/4” (19 mm) ID; 3/4 npt x
1/2 npt (mbe); 22” (559 mm) long 1
20 100–322 WASHER, lock; 3/8” 2
21 100–131 NUT
, hex; 3/8–16 1
22Y290–138
LABEL, warning 4
23 180–916 MANIFOLD; adapter; 3/4 npsm(m) x
3/4 npt(f) x 1/4 npt(f) 1
24 103–347 RELIEF VAL
VE, air;
100 psi (7 bar , 0.7 MPa) 1
25 100–023 W
ASHER, flat; 3/8” size 4
26 100–057 CAPSCREW
, hex hd;
5/16-18 x 3/4” (19 mm) long 2
27 237–771
HANDLE, bleed 1
28n184–420 WIPER; synthetic rubber 1
29 112–980 SCREW
, machine, flat-hd;
stainless steel;
1/4–20 x 1” (25 mm) long 8
30 190–427
RING, retaining; stainless steel 1
31 190–374 PLA
TE, wiper; aluminum 1
32 109–482 O-RING; Vitonr1
33n184–421
WIPER; polyethylene 1
34 276–049 SP
ACER; polyurethane 1
35 112–978 PETCOCK, air assist; 1/4 npt(m x f) 1
36 100–175
COUPLING; 1/4 npt(fbe) 1
37 190–425
NIPPLE, pipe; 1/4 npt; 153 mm (6”) 1
n
Keep these spare parts on hand to reduce down time.
{ These parts are included in Air Regulator Kit 238–724.
Y Replacement Danger and W arning labels, tags and cards
are available at no cost.
05321
35
36
37
31
27 32
26
34
29
30
33n
28n

 
Technical Data
Category Data
Maximum fluid working pressure 214 bar , 21.4 MPa (3100 psi)
Maximum air input pressure 10 bar , 1.0 MPa (150 psi)
Maximum pump air input pressure 7 bar , 0.7 MPa (100 psi)
Ratio 31:1
Pump performance data See pump manual 308–351
Air consumption data See pump manual 308–351
Air inlet size 3/4 npsm(f)
Fluid outlet size 1” npt(f)
Fluid inlet size Priming Piston
Maximum operating temperature 82 C (180 F)
W etted parts Pump: See pump manual 308–351
W iper Plate: Aluminum, synthetic rubber , stainless steel, ultra-high
molecular weight polyethylene, polyurethane, polyethylene, V iton
Viton is a registered trademark of the DuPont Co.
Sound Pressure Levels (dBa)
(tested in accordance with ISO 3744)
Input Air Pressures at 15 cycles per minute
Air Motor
2.8 bar ,
0.28 MPa
(40 psi)
4 bar ,
0.4 MPa
(58 psi)
4.8 bar ,
0.48 MPa
(70 psi)
6 bar ,
0.6 MPa
(90 psi)
7 bar ,
0.7 MPa
(100 psi)
Standard Bulldog 83.0 dBa 85.7 dBa 87.5 dBa 90.5 dBa 91.0 dBa
Manual Change Summary
Assembly
Changed Part Status Ref. No. Part No. Name
237–263
Ram–
Mounted
Pump
Deleted 3 237–702 Wiper Plate;
replaced by
ref. nos. 26
through 37.
Old 16 103–893 Elbow
New 16 100–840 Elbow
Quantity
change 17 100–509
Plug; qty: 2.
Old 20 100–133 W asher; qty: 1.
New 20 100–322 W asher; qty: 2.
Assembly
Changed Part Status Ref. No. Part No. Name
Added 23 180–916 Manifold
Added 24 103–347 Relief V alve
Added 25 100–023 Washer
Added 26–
37 See
page 13
Replace
237–702
Wiper Plate
(see above)

308-471 15
Dimensions

A
B
C
D
E
FG
14.2 mm (0.56 in.)
Diameter Holes
Pump
Model A (Raised) B (Lowered) C D E F G Weight
237–263 1763 mm
(69 in.)
1349 mm
(53 in.)
279 mm
(1 1 in.)
356 mm
(14 in.)
356 mm
(14 in.)
432 mm
(17 in.)
546 mm
(21.5 in.)
104 kg
(230 lb)

16 308-471
The Graco Warranty and Disclaimers
WARRANTY
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects
in material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. Graco will,
for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defec -
tive. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’ s written rec-
ommendations.
This warranty does not cover , and Graco shall not be liable for general wear and tear , or any malfunction, damage or wear
caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident,
tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by
the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the im -
proper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not sup -
plied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor
for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective
parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not
disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the
costs of parts, labor , and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PUR-
POSE.
Graco’
s sole obligation and buyer ’ s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no
other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or prop -
erty
, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two
(2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE IN CONNECTION WITH
ACCESSORIES, EQUIPMENT , MA TERIALS, OR COMPONENTS
SOLD BUT NOT MANUFACTURED BY GRACO.
These items sold, but not manufactured by Graco (such as electric motors,
switches, hose, etc.) are subject to the warranty , if any , of their manufacturer . Graco will provide purchaser with reasonable assis -
tance in making any claim for breach of these warranties.
For Sales to Canadian Customers:
Except as expressly stated herein, Graco makers no representations, warranties or conditions, express, implied or collateral, con -
cerning
any goods or services sold, and GRACO SHALL NOT BE LIABLE IN ANY MANNER FOR any other representation,
warranty or condition of any kind, whether arising by operation of law or otherwise, including but not limited to, WARRANTIES OF
MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE.
LIMITATION OF LIABILITY
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equip -
ment hereunder , or for the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of
contract, breach of warranty , the negligence of Graco, or otherwise.
Graco Phone Number
TO PLACE AN ORDER , contact your Graco distributor , or call this number to identify the distributor closest to you:
1–800–367–4023 T oll Free
Sales Offices: Atlanta, Chicago, Detroit, Los Angeles
Foreign Offices: Belgium, Canada, England, Korea, Switzerland, France, Germany , Hong Kong, Japan
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
PRINTED IN U.S.A. 308–471 July 1995 Revised July 1996