Meyer Sound Reinforcement Loudspeaker UPM-2 User manual

Features
Ultra-compact
Lightweight
Efficient high power
Versatile
Uncompromised quality
Controlled coverage
Long-term reliability
Applications
Delayed fill in installations
Music playback in small clubs
Multi-channel AV playback
Cinema surround channels
Stage monitoring
Paging and announcing
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
[phone]
FAX [phone]
Designed for sound reinforcement
applications requiring minimum size, the
UPM-2 delivers high sound pressure levels
with low distortion and highly controlled
coverage in both axes.
Suitable for a wide range of applications
from music playback and delay fill systems
to stage monitoring, the UPM-2 features
outstanding low-frequency performance in
an unusually compact package. Its ultra-
flat frequency response simplifies room
equalization requirements and ensures
high gain-before-feedback.
The loudspeaker consists of two 5-inch
low-frequency cone drivers in a vented
enclosure, and a proprietary titanium dome
(U.S. patent no. 4,152,552) high-frequency
driver and high-Q constant-directivity
horn with passive crossover.
The rugged cabinet is easily handled
and installed. It has three
3
⁄ 8 "-16 threaded
rigging points, and may be mounted on a
stand. An optional steel bracket facilitates
mounting in permanent installations.
The UPM-2 system requires a high-
quality professional power amplifier
capable of delivering 125 watts continu-
ously into 16 ohms, with a signal voltage
gain of 10 dB (minimum) to 30 dB
(maximum).
UltraSeries™
Reinforcement
Loudspeaker
UPM-2
—— 6
—
—— 4
—
—— 2
—
—— 0
Inches
UPM-2.PM6 2/4/96, 11:20 AM1

UPM-2 Specifications
Acoustical – UPM-2/P-2
Frequency Response
1
Half space 60-20,000 Hz +4 dB
Free air 70-20,000 Hz +4 dB
Maximum SPL
2
Continuous 108 dB
Peak 118 dB
HF Distribution Pattern (-6dB points)
Horizontal 45 degrees
Vertical 45 degrees
UPM-2 Loudspeaker
Driver Complement
Low-Frequency (2) MS-5 5-inch cone drivers, 8 ohms per driver
High-Frequency 1" titanium dome horn driver, 8 ohms
Passive Network
Function 3-way crossover and HF driver protection
Capacitor Type Polypropylene
Inductor Type Ferrite core
Nominal Impedance 16 ohms
Enclosure 0.2 cu. ft. vented, multi-ply Finnish birch
Finish Black textured
Connector EP 4 (EP 5, Europe only) or 3-pin XLR (male and female)
Protective Grill Expanded metal screen frame, vinyl damped,
charcoal-grey foam covering
Mounting Points
3
⁄8"-16 nut plates
Physical Dimensions 6
3
⁄4" W x 18
1
⁄8" H x 7
1
⁄8" D
Weight 16 lbs. (7.3 kg)
P-2 Control Electronics Unit
Input Type Balanced (active), 47k ohms
Output Type Push-pull (active), 200 ohms source impedance
Maximum Input/Output Level
3
Unbalanced >+20 dBu
Balanced >+26 dBu
Hum and Noise
4
<–90 dBV
Dynamic Range
5
>105 dB
Sense Input 10K ohms true differential
Driver Protection Circuitry
Low Frequency RMS Limiter
High Frequency RMS and Peak Limiter
Indicators
Sense Green LED
Limit Red LED
Power Green LED
Controls Level control, AC on/off switch, Lo Cut switch
Connectors
Balanced Input/Output 3-pin XLR (A-3)
Sense Input Banana jacks
Power 120/240V AC, 50/60 Hz (internally switchable)
Physical Dimensions 19" W x 1
3
⁄4" H x 7
3
⁄4" D Standard rack mount
Weight 7 lbs. (3.2 kg)
Note 1:
Measured 1 meter on axis,
pink noise input, in third-
octave ISO bands.
Note 2:
“A”-weighted noise input,
loudspeaker driven by
125␣watt (16 ohm rating)
mono amplifier.
Note 3:
1 kHz, 10k
Ω load, < 0.1%
THD.
Note 4:
“A” weighted.
Note 5:
Noise floor to maximum
output.
UPM-2.PM6 2/4/96, 11:20 AM2

The P-2 Control
Electronics Unit
UPM-2 Physical Dimensions
The UPM-2 operates as a system
with the P-2 Control Electronics Unit.
Optimized for the UPM-2 and pre-aligned
at the factory, the P-2 contains frequency
response and phase response alignment
circuitry, and Meyer Sound’s exclusive
SpeakerSense ™ driver protection circuitry,
incorporating both peak and RMS signal
limiting.
SpeakerSense protects the UPM-2
loudspeaker components from damage due
to overheating under high power condi-
tions. This unique circuit continuously
monitors the power applied to the UPM-2
drivers, and limits the signal output when
the safe operating limits of the drivers are
exceeded. Until the onset of overload, the
SpeakerSense circuitry has no effect on the
signal.
Six stages of Meyer’s exclusive comple-
mentary phase equalization in the P-2
Control Electronics Unit give the UPM-2
flat frequency response with outstanding
phase characteristics.
A single-channel device operating at line
level, the P-2 is the final component in the
signal chain before the amplifier.
6.84"
7.00"
7.5°
7.70"
8.63"
18.00"
3.63"
C
UPM-2.PM6 2/4/96, 11:20 AM3

Architectural and
Engineering Specifications UPM-2⁄P-2
Meyer Sound Laboratories has
devoted itself to designing,
manufacturing, and refining com-
ponents that deliver superb sonic
reproduction. Every part of every
component is designed and built
to exacting specifications and
undergoes rigorous, comprehen-
sive testing in the laboratories.
Research remains an integral,
driving force behind all produc-
tion. Meyer strives for sound
quality that is predictable and
neutral over an extended lifetime
and across an extended range.
© 1995 Meyer Sound 04.030.006.01 A
Sound
engineering
for the art
and science
of sound.
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
( 510 ) 486-1166
FAX ( 510 ) 486-8356
The ultra-compact, high-power rein-
forcement speaker system shall be a passive
3-way type with two 5-inch low-frequency
loudspeakers, front mounted in a ducted
bass-reflex hardwood plywood enclosure
with a 45°high-frequency waveguide and
titanium dome driver. The enclosure shall
be fitted with three
3
⁄ 8 "–16 threaded
mounting points, and shall operate with
a separate Control Electronics Unit.
The Control Electronics Unit shall con-
tain a power supply capable of operating
from a 120/240V AC 50/60 Hz line, equal-
ization circuitry for amplitude and phase
alignment, protection circuitry which
automatically activates under high power
conditions, RMS limiter which protects
the speakers from overheating, active bal-
anced input, active push-pull output, and
LED indicators for power on and limiters.
Total harmonic distortion at + 26 dBu
at the balanced output loaded with 10kΩ
shall be less than .1% at 1kHz. The “A”-
weighted noise level shall be at least 105 dB
below maximum rated output
of +26 dBu.
The speaker system combined with a
125␣W (16 ohm rating) amplifier shall
meet the following performance criteria:
Frequency response, 60 Hz to 20 kHz plus
or minus 4 dB measured in half space
at 1 meter on axis with
1
⁄ 3 octave pink
noise; output of 108 dB SPL measured at
1 meter on axis with peaks of 118 dB SPL
when driven with “A”-weighted noise.
High frequency distribution pattern, 45
degrees horizontal by 45 degrees vertical.
Speaker enclosure dimensions shall be
6
3
⁄ 4 " W x 18
1
⁄ 8 " H x 7
1
⁄ 8 " D, weight 16 lbs
(7.3 kg).
Control Electronics Unit dimensions
shall be 19" W x 1
3
⁄ 4 " H x 7
3
⁄ 4 " D, weight
7␣lbs (3.2 kg).
The speaker enclosure shall be the Meyer
Sound UPM-2. The Control Electronics
Unit shall be the Meyer Sound P-2.
UPM-2.PM6 2/4/96, 11:20 AM4