Meyer HOTSHOT-50 User manual

BY
OWNER'S MANUAL
9-16 Part #52151MY
Model #38165
High Performance Snow & Ice Control Equipment
HOTSHOT-50
DROP SPREADER

PARTS LIST FOR HOTSHOT 50
ASSEMBLY
Reference Parts List below for part identication
HOTSHOT 50 Parts List
Key Part# Description Key Part# Description Key Part# Description
1PSB60272 AGITATOR AXLE ASSEMBLY 10 PSB32106 10-24 WING NUT ZINC 19 PSB12176 SHUT OFF
2PSB16131-MY HOPPER ASSEMBLY 11 PSB32100 1/4-20 HEX NUT ZINC 20 PSB32108 10-24 HX. NUT ZINC PLATED
3PSB31141 #14 X 3/4" TYPE "AB" HWHS 12 PSB60379 WIRE HSG ASSEMBLY 21 PSB12261 END CAP HOPPER
4PSB60205 UPPER HANDLE W/GRIP 13 PSB37106 1/4-20 X 2" CARRIAGE BOLT 22 PSB37111 10-24 X 1" CARRIAGE BOLT
5PSB37108 1/4-20 X 1 3/4" CARRIAGE BLT 14 PSB60027 WING NUT ASSEMBLY 23 PSB36208 #6 X 3/8" TYPE 25 PHPS S.S.
6PSB31133 #8 X 3/4 PHPS TYPE A 15 PSB25113 FRAME 24 PSB33106 1/8" X 3/4" COTTER PIN ZINC
7PSB12319 UPPER HOUSING CLIP 16 PSB12265 END CAP SHUT OFF 25 PSB33107 1/8" X 1 3/4" COTTER PIN S.S.
8PSB60526 CONTROL ASSEMBLY 17 PSB70109DR 5 SPOKE 12" WHEEL 26 PSB34103 1"OD X 17/32"ID X 1/32" WASHER
9PSB12223 INDICATOR-DROP 18 PSB12132 BEARING 27 PSB70142 NUT PROTECTOR .234 ID. X .375 IL.
2
1
4
5
23
14
17
18
19
20
7
18
21
17
22
3
12 13
25
16
6
6
27
13
15
10
9
8
11
24
26
BY
Remove spreader from the carton.
Remove the (#14) Wing Nut from the (#13) ¼ - 20 x 2" Carriage Bolt and
from the (#15) Frame.
Now install (#4) Upper Handle onto the outside of the (#15) Frame and
install (#13) Carriage Bolts and (#14) Wing Nuts as shown in the Parts
List. Tighten fully.
1.
2.
3.
BY
Meyer Products, Inc.
18513 Euclid Ave
Cleveland, Ohio 44112
216-486-1313
www.meyerproducts.com

OPERATION
WARRANTY
MAINTENANCE
Meyer Products, Inc. warrants to Purchaser the following:
Meyer Products, Inc., warrants to the original purchaser for a period of one year from the date of purchase of Meyer® brand spreader products that
they will be free from defects in materials or workmanship, with the exceptions stated below. No person is authorized to change this warranty or to
create any additional warranty on Meyer® products.
Meyer Products will repair any product that proves to be defective in materials or workmanship. In the event repair is not possible or practical (as
determined by Meyer Products in its sole discretion), Meyer Products will either replace the product with a new product of similar model and price,
or refund the full purchase price, as determined by Meyer Products. Customer must keep the complete spreader system serviced/maintained as
recommended by Meyer Products.
This warranty does not cover:
• Problems caused by failure to follow the product instructions, or failure to maintain the product as described in the Operator’s Manual;
• Damage resulting from rust, corrosion
• Damage caused by usage that is not in accordance with product instructions (use of the spreader for any purpose other than spreading approved
material is considered misuse and abuse);
• Anyspreader,oranypart,component,orassemblythereof,whichhasbeenmodiedoraltered;
• Problems caused by using accessories, parts, or components not supplied by Meyer Products;
• Cost of tax, freight, transportation or storage charges, environmental charges, solvents, sealants, lubricants or any other normal shop supplies.
• Problemscausedbycollision,re,theft,vandalism,riot,explosion,lightning,earthquake,windstorm,hail,water,ood,oranyotherActsofGod;
• Liability for damage to property, or injury to, or death of any person arising out of the operation, maintenance or use of the covered product;
• Products with missing or altered serial numbers;
How To Get Service:
• It is the responsibility of the original purchaser to establish the warranty period by verifying the original delivery date. A bill of sale, cancelled
check or some other
appropriatepaymentrecordmaybekeptforthatpurpose.Itisrecommended,butnotrequired,thattheconsumerverifytheoriginaldeliverydateby
immediately returning the attached Warranty Registration Card.
How State Law Applies:
Thiswarrantygivesyouspeciclegalrights,andyoumayalsohaveotherrightswhichvaryfromstatetostate.
BY
Never store material in spreader. Return unused product to its original container.
Wash spreader thoroughly after each use and dry completely in the sun or heated area.
Lubricate the metal control wire at the hopper mounting point regularly, we recommend
aparinbased(chapsticktype)lubricant.
To reduce the possibility of rust, coat the inside of all steel tubing with Fluid Film or
similarcorrosioninhibitor.Storespreaderwithshut-o󰀨inopen#30position.
1.
2.
3.
4.
WASH
;Beforellinghopper,makesurespreadercontrolisin
the “CLOSED”position.Alwaysllspreaderonwalk
or drive, not on the lawn.
;Position the rate control stop to the desired setting. If
settingisnotknown,trydi󰀨erentsettingsuntildesired
results are achieved.
;Always push spreader, do not pull. Start spreader in
motion and as it passes over the area to be treated,
move the control lever to "OPEN" to the "STOP"
position. Push to “CLOSE” the spreader at the end of
each pass.
;Operate spreader at normal walking speed
;Apply two header strips at each end of the area to be treated and then proceed length-wise between the header
strips. Be sure to overlap the wheel tracks slightly to prevent missed strips.
;Apply ice melt prior to the storm to reduce unmanageable levels of ice and snow.
CLOSE
OPEN