Mi Home MIHO008 User manual

This is a radio controlled switch for the switching of
mains power to lighting and appliances up to 250W.
Only the Line is switched to the load. Switching is
initiated either by radio control or manually by
pressing the button on the housing. It is compatible with
Mi|Home Remote Control (MIHO003) and the Mi|Home
network. It is a receive-only device operating in the
433MHz ISM short-range band using OOK modulation.
In the Box:
Light Switch, Screw Fittings, User Guide
Compatibility
We recommend incandescent & halogen bulbs which
are 250W max, or dimmable LED bulbs which are
maximum 50W in total and not exceeding 6 bulbs per
swtich. Not suitable for uorescent, non-dimmable LED
and CFL bulbs or any light requiring line drivers.
Installation
This device operates at UK mains voltage levels
Therefore, we advise installation from a competent,
qualied person. It can t into a 25mm metal pattress or
35mm dry lining pattress box, but not into a 4 lug box.
NOTE: Can only be used in a two way switching
conguration with a MiHome slave switch. Using any
other switch as a slave will damage the switch.
IMPORTANT:
Applicable in England and Wales, where the installation
of this product falls under the scope of the Building
Regulations requirements for Part P, the installation
must be carried out by registered competent persons
and certied as follows:
a. Self-certication by a registered competent person
b. 3rd-party certication by registered 3rd-party certier
c. Building control body
For an installation that is not notiable according to the
Building Regulations Part P, work should be designed
and installed, and inspected, tested and certicated in
accordance with BS 7671.
Applicable in Scotland, where the installation of this
product falls under the Building (Scotland) Act, a
Warrant may be required and advice should be sought
from LABSS (Local Authority Building Standards
Scotland. We recommend that a competent qualied
person is used for all installations of this product even
if the installation is deemed to be minor works and
non-notiable for the purposes of the Building
Regulations. Non-notiable electrical work can present a
risk to safety. If qualied electricians carry out the work
they should give you a Minor Works Certicate, which
means that they have tested the work to make sure
it is safe. If you do the work yourself you may wish to
engage a qualied electrician to check it for you. Note
that it is the owner of the property who has the legal
liability for complying with the Building Regulations.
MI|Home Light
Quick Start Guide
Pairing
To control Switch remotely it must be paired with a
controlling device such as MiHome Remote Control or
MiHome Gateway.
Pairing with MiHome Remote Control
To set the unit into pairing mode, press and hold the
button on the front of the light switch housing for 5
seconds or so until the lamp on the front starts to ash.
NOTE: A single press of the button while it is ashing
will take it out of pairing mode.
Point the hand controller at the light switch at a range
of up to 2m and then press and hold the chosen “ON”
button on the remote handset for 2 seconds or so. You
should see the lamp on the Light Switch housing ash
more quickly for a brief period indicating the pairing has
succeeded.
Pairing with the MiHome Gateway
Select the Light Switch from the list of devices to pair
from your MiHome account and follow the on-screen
pairing instructions.
NOTE: The Switch can be paired with up to 5 separate
controllers – remote controls and Gateways alike.
Further attempts to pair will overwrite previous pairings.
Remote Control Operation
Once paired with a remote controlling device the unit
can be switched on and o with that controller. With
the Energenie hand controller it can be controlled with
the on/o buttons to which it is paired and the all on/
o buttons by pressing and holding the chosen “On” or
“O” button on the remote handset for 1 second.
Follow instructions on the MiHome app or MiHome
server to control the device. You can program it to
switch with conditions such as events and time of day.
Manual Operation
A single short press of the button on the front of the
housing will simply toggle the switch on and o.
What the push button does
1. Single short press to toggle power on/o
2. Long press - 5 secs: Learning mode (slow LED ash)
What the LED indicator lamp means
1. Red = ON, o = OFF
2. Slow ashing = pairing mode
3. Quick ashing = pairing accepted
Disposal
The outer box of the packaging is 70% recycled material
from managed forests and is 100% recyclable.
Do not dispose of switch with regular household waste.
You must take electronic equipment to a local recycling
centre to be disposed of in line with current regulations.

Copyright Notice
© 2018 Sandal Plc.
User Manual
Part no: MIHO008
Energenie and MiHome are brand names of Sandal Plc.
Registered Oce: Claremont House, Deans Court, Bicester,
Oxon, OX26 6BW
Safety
If you do not install and use in line with this guide the
warranty will become invalidated and we will not be
liable for any damage or loss whatsoever, including
indirect loss, damage to property or personal injury.
You must only use the product in dry areas indoors, and
it must be protected from moisture and water.
Do not disassemble as it does not contain any parts to
service. If it arrives faulty, return it to where purchased.
Technical Specication
• Rating: 220 - 240V~ 50Hz, 1A, 250W max.
• Terminal Connections: L (Line in), L1 (Line out), Slave
ii(MiHome only)
• Manual control: Push Button
• Indicator lamp: Red LED
• Radio: 433.92MHz ISM short range; OOK, simplex one
iiway; 2400 baud at 4800 bit/s; Manchester encoding
• Range: Approx. 15-20m in closed; 30m in open area
• Operating temp. : -5°C to 40°C
• Storage temp. : -20°C to +60°C
• Housing: White plastic (MIHO08); Black Nickel
ii(MIHO24); Chrome (MIHO25); Brushed Steel (MIHO26)
• Mounting: 25mm metal pattress; 35mm dry lining
• Size (HxWxD): 85 x 85 x 28mm; Weight: 95g
• Protection class: IP20
• Approvals: EN 60669-2-1, EN301489-1, EN301489-3
Troubleshooting
For further help please visit mihome4u.co.uk/
troubleshooting or email [email protected]
Installation Example
Remote Control Operation
2011/65/EU Restriction of the Use of Certain
Hazardous Substances (RoHS)
Directive Recast
The unit complies with all essential requirements of the
above referenced specications and directives and has
been issued a CE mark as per directive 93/98/EEC.
The Technical Construction File required is maintained
at the company headquarters at 5 Harold Close, The
Pinnacles, Harlow, Essex, England, CM19 5TH.
Other Notices
THIS DEVICE AND ASSOCIATED SOFTWARE ARE
NOT DESIGNED, MANUFACTURED OR INTENDED FOR
USE OR RESALE FOR THE OPERATION OF NUCLEAR
FACILITIES, THE NAVIGATION, CONTROL OR
COMMUNICATION SYSTEMS FOR AIRCRAFT OR
OTHER TRANSPORTATION, AIR TRAFFIC CONTROL,
LIFE SUPPORT OR LIFE SUSTAINING APPLICATIONS,
WEAPONS SYSTEMS, OR ANY OTHER APPLICATION
IN A HAZARDOUS ENVIRONMENT, OR REQUIRING
FAIL-SAFE PERFORMANCE, OR IN WHICH THE
FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO
DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL
OR ENVIRONMENTAL DAMAGE (COLLECTIVELY,
“HIGH RISK APPLICATIONS”). YOU AGREE AND
ACKNOWLEDGE THAT YOU HAVE NO LICENSE TO,
AND SHALL NOT (AND SHALL NOT ALLOW A THIRD
PARTY TO) USE THE PRODUCT IN ANY HIGH RISK
APPLICATIONS, AND WHERE PERMITTED BY LAW
SANDAL PLC SPECIFICALLY DISCLAIMS ANY
WARRANTY REGARDING, AND ANY LIABILITY
ARISING OUT OF, HIGH RISK APPLICATIONS.