Mi Action Camera 4K User manual

Mi Action Camera 4K User Manual

1. Package Contents
Mi Action Camera 4K x 1
User manual x 1USB cable x 1
Baery x 1
MiAction Camera Baery
Mi Action Camera 4K User Manual

2. Product Overview
Lens Top Indicator Port Protective Cover
Front Indicator Microphone Micro-USB Port
Function Buon Speaker Microphone
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9

10
14
15
11
12
13
Touch Screen Baery Cover Baery
Lock Buon 1/4-inch Thread Hole MicroSD Card Slot
10
11
14
15
12
13

a. Remove the baery cover (as shown in the figure), align the baery pins with the direction
of the lens, and insert the baery. To remove the baery, gently pull the handle bar on the
baery.
b. Keep the label side of the MicroSD card towards the back of the camera body, and insert
the card into the card slot. To remove the MicroSD card, gently press the top edge of the
card to eject it from the slot.
3. Install andDisassemble
Do not damage the handle bar.
MicroSD Card
Press the baery cover lock buon and
push the baery cover outwards.

4. Baery Charging
Red
Off
Note:
It is recommended to remove the baery if you connect the camera to a power supply for
a prolonged period during use.
a. You can use a 5V 1A power adapter, PC, or mobile power bank to charge the camera
via a data cable. It is recommended to turn off the camera during charging.
b. The front indicator is solid red while charging, and turns off automatically when the
baery is fully charged.

a. Power-on/Power-off
Power-on: Press and hold the function buon for about 3 seconds, followed by a power-on sound.
Power-off: Press and hold the function buon for about 3 seconds, followed by a power-off sound.
b. Photo
Select the photo mode, and press the function buon to take photos.
c. Video
Select the video mode, and press the function buon to start the recording.
Press the function buon again to stop the recording.
5. Operating Instructions
Function buon
Note:
When shooting a 4K-video, it is recommended to use a main brand UHS-3 MicroSD card
with a capacity not less than 16 GB.
Video files are stored in the FAT32 format. The maximum size of a single video file is 4 GB.
A video file exceeding 4GB will be fragmented for storage.

d. Operating screen
The preview page is displayed aer the camera is powered on (in screen lock mode, you
can double-tap the screen or press the function buon to wake up the camera).
Camera setup
On the preview page, slide down to enter setup page. Slide the
screen in the reverse direction or press the function buon to
return to the preview page.
Media library
On the preview page, slide leward to enter media library preview
page. Slide the screen in the reverse direction or press the function
buon to return to the preview page.
Note: A MicroSD card needs to be installed.
Mode selection
On the preview page, slide rightward to enter mode selection page.
Slide the screen in the reverse direction or press the function buon
to return to the preview page.
photo TimeLapse BurstPhotos
延时摄像 SlowMotion
Video
Wi-Fi setup / Bluetooth device connection
Tapto enable or disable the Wi-Fi function.
Select the bluetooth device in the setup page, and connect according
to the prompt

6. QuickSetup
Control your device and interact it with other smart home devices in Mi Home App.
a. Download Mi Home App
Scan the QR code or go to App store to download and install Mi Home App.
b. Add and connect a Mi Action Camera 4K
Open Mi Home App, tap "+" on the upper right to add your device, and your device will
appear in the homepage. Install the plug-in and follow prompts to add the device.
Open the Mi Action Camera 4K plug-in.
Turn on Mi Action Camera 4K and slide down to access the shortcut menu page. Enable
the Wi-Fi function.
Tap "Connect" on the App, and follow the instructions to complete the Wi-Fi connection.

7. Indicator Status
Status Description
Powered on indicator
No card/Card error
Upgrading
Photo shooting/Video recording
Front indicator On
Front/Top indicator Slow blinking
Front indicator Fast blinking red
Front/Top indicator Fast blinking alternately
Note: When the front indicator is blue, the unit is fully charged; when it is yellow, the
baery is adequate; when it is red, the baery is low.
Note:
The GPS must be activated for some certain phones when searching for the Mi Action
Camera 4K via Wi-Fi.
Aer the App is connected to the camera successfully, Android phones disconnect the
Internet and a prompt indicating no Internet connection is displayed on some certain
phones. In this case, choose to maintain the current connection.
To upgrade the camera firmware, you need to maintain the phone's connection to the
Internet.

8. Specifications
Product name: Mi Action Camera 4K
Dimensions: 2.81 x 1.68 x 1.16 inches
Net weight: 3.49 ounces (including baery)
Operating temperature: 32℉~104℉
Storage temperature: -4℉~140℉
Wireless connections: Wi-Fi IEEE 802.11b/g/n
Maximum photo resolution: 3840 x 2160
Maximum video resolution: 3840 x 2160p at 30 fps
Model: YDXJ01FM
Aperture: F2.8
Focal length: 3.2 mm
Wide angle: 145°
Bluetooth version: Bluetooth 4.1
Recording: dual microphone
MicroSD card: maximum 64GB
Screen: 2.4’’
9. Precaution
a. Do not put the baery into fire or smash the baery. The capacity of the lithium baery
shrinks substantially at low temperature. Therefore, do not use it in an environment
below 32℉.
b. Keep the product properly and keep the lens away from scratches and dirt. Use a
professional brush and lens blower to clean the product. Protect the product against
dirt and damp during storage.
c. In case of waterproof case is not mounted, please don‘t use the camera in harsh
environments such as underwater, rain, dust and severe cold etc.

CAUTION
RISK OF EXPLOSION IF BATTERIES IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCIONS.
Old electrical appliances must not be disposed of together with the residual
waste, but have to be disposed of separately. The disposal at the communal
collecting point via private persons is for free. The owner of old appliances is
responsible to bring the appliances to these collecting points or to similar
collection points. With this lile personal effort, you contribute to recycle val-
uable raw materials and the treatment of toxic substances.
Environmentally friendly disposal

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Please note that changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular
in-stallation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired opera-tion of the device.Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
broullage est susceptible d'en compromere le fonctionnement.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF
exposure compliance. This transmier must not be co-located or operating in conjunction
with any other antenna or transmier.
The portable device is designed to meet the requirements for exposure to radio waves
established by the Federal Communications Commission (USA). These requirements set
a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported
under this standard during product certification for use when properly worn on the body.
During testing, this product are set to their highest transmission levels and placed in
positions that simulate uses against the body with 5mm separation.

This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF
exposure compliance. This transmier must not be co-located or operating in
conjunction with any other antenna or transmier.
The portable device is designed to meet the requirements for exposure to radio waves
established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over
one gram of tissue. The highest SAR value reported under this standard during product
certification for use when properly worn on the body.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies
pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions
spécifiques pour satisfaire les normes. Cet émeeur ne doit pas être co-implanté ou
fonctionner en conjonction avec toute autre antenne ou transmeeur.
Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes
radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite
de 1.6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée
en vertu de cee norme lors de la certification de produit à utiliser lorsqu’il est
correctement porté sur le corps.
The highest SAR value for this YDXJ01FM camera when properly worn on the body is
0.144 W/kg, for ICNIRP recommendation. SAR is measured against head and with the device
at a separation of 5 mm to the body, while transmiing at the highest certified output power
level in all frequency bands of the mobile device.

Principal: Xiaomi Communications Co., Ltd.
Manufacturer: Beijing FIMI Technology Co., Ltd.
For further information, please go to www.mi.com/en/
Address：No.348, Floor 3, 1# Complex Building, Yongtaiyuan jia, Qinghe,
Haidian District, Beijing, China
Read this manual carefully before use, and
retain it for future reference.

Caméra d’action 4K Mi Mode d’emploi

1. Contenu du paquet
Caméra d’action 4K Mi x1
Mode d’emploi x1Câble USB x1
Baerie x1
MiAction Camera Baery
Caméra d’action 4K Mi Mode d’emploi

2. Présentation du produit
Objectif Indicateur supérieur Protection du port
Indicateur avant Micro Port micro-USB
Bouton de fonction Haut-parleur Micro

Écran tactile Couvercle de baerie Baerie
Bouton de verrouillage Trou fileté de 1/4po Emplacement pour
carte micro SD