Micca MB42X-C User manual

Home Audio Products
Micca MB42X-C 4-Inch 2-Way
Loudspeaker
Thank you for purchasing the Micca MB42X-
C Center Channel Speaker! This product has
been designed for optimal audio
reproduction performance in a variety of
home entertainment configurations, with
accuracy, clarity, and impact that discerning
audiophiles listen for.
Please take the time to become familiar with
the MB42X-C and the placement options as
detailed in this manual.
General Recommendations
Height - For normal listening from a fixed
listening area, the MB42X-C should ideally be
placed at the ear-level of the listener, with the
listener comfortably situated in the listening
location. If it is not possible to achieve ear-level
height, use foam wedges to tilt the speaker up or
down to point it to the listener.
Orientation - The MB42X-C is designed to work
very well whether placed horizontally or
vertically. The vertical placement provides better
dispersion characteristics, but the horizontal
placement is suitable when it is impractical to
use the speaker vertically.
Usage-Specific Recommendations
Center Channel Speaker
When used as a center channel speaker, make
sure the two front speakers are well matched in
timber to the MB42X-C. This can be achieved by
using a pair of the MB42X bookshelf speakers,
or two additional MB42X-C speakers as the left
and right speakers. Try to place all three left,
right, and center speakers close to the same
height. Speaker height should be selected so
that it is as close to ear level as possible while
considering whether listeners will be seated or
standing in the listening area.
Stereo Speaker on Stands
When a pair of MB42X-C is used vertically with
speaker stands, it is important to select speaker
stands that place the speakers to the ear level of
the listener. Do this by measuring the height of
the listener’s ear when seated in the listening
area, and subtracting 8 inches. For example, if
the listener’s ear is measured at 36 inches from
the floor when seated, select speaker stands
that are approximately 28 inches high.
Speaker Wire
The MB42X-C should be connected to the
amplifier with good quality oxygen-free copper
speaker wire for best performance.
The gauge or thickness of the speaker wire can
affect the performance of the MB42X-C. Always
choose a speaker wire of the appropriate gauge
to prevent excessive speaker wire resistance.
Using undersized speaker wire can result in lose
of volume, detail, and dynamic range. Please
select speaker wire for the MB42X-C based on
the following minimum recommendations:
50' or less - 16 Gauge 2 Conductor
50' - 80' - 14 Gauge 2 Conductor
80'-120' - 12 Gauge 2 Conductor
120'-200' - 10 Gauge 2 Conductor

Amplifier Connection
Amplifier speaker output terminals are typically
color coded with black for negative (-) and red
for positive (+). Similarly, the MB42X-C has
speaker wire terminals with a black and red
color coding. When connecting speaker wire,
ensure that the positive terminal on the amplifier
is connected to the positive terminal on the
MB42X-C. And similarly, the negative terminal
on the amplifier should be connected to the
negative terminal on the MB42X-C.
Speaker wires typically use at least one of
several possible methods to help maintain
correct polarity, including color coded insulation
or conductor strands, or printing of text and
symbols along one side of the wire insulation.
Amplifier Considerations
The MB42X-C’s impedance varies between 4 to
8 Ohms. Care must be taken to ensure that the
amplifier is capable of handling a 4-Ohm load.
Some amplifiers have a switch that must be set
to select a 4-Ohm compatible operation mode.
Improper amplifier selection or setup may result
in permanent damage to the amplifier or speaker.
The MB42X-C can be used with amplifiers
between 15 to 100 watts per channel as long as
reasonable care is exercised. If there is audible
distortion, turn down the volume until the
distortion goes away. Never allow the speaker
and amplifier to play for more than a few
seconds when there is audible distortion.
Removing the Grill
The MB42X-C has a removable grill that is held
in place by four high strength magnets. To
remove the grill, carefully pry the grill off from
edge until the magnets are fully disengaged. To
avoid damaging the speaker drivers, do not
touch them either with or without the grill in
place.
The MB42X-C can be used without the grills
installed as long as care is taken to prevent the
drivers from damage such as by hard/sharp
objects, liquids, pets, or hands. Store the grills in
a safe dry place when not in use.
MB42X-C Specifications
Woofer: Dual 4” Carbon Fiber Cone with Rubber Surround
Tweeter: 0.75” Silk Dome
Crossover: 12dB/Octave
Enclosure: Ported Cabinet
Frequency Response: 60Hz-20kHz (Typical In-Room)
Impedance: 4-8 Ohms
Sensitivity: 86dB 1W/1M
Power Handling: 100 Watts (Each)
Dimensions: 5.3” (H) x 15” (W) x 7.1” (D)
Information in this manual is believed to be accurate and reliable but Micca Ltd assumes no responsibility for its use nor for any
infringement of patents or other rights of third parties which may result from the use of this manual or the product. Micca
reserves the right to change product specifications at any time without notice.
Micca, MB42X, MB42X-C, and the Micca logo are trademarks of Micca Ltd. Other trademarks referenced in this manual are the
properties of their respective owners.
© 2012-2013 Micca Ltd. All rights reserved.