Microcom 485TC User manual

QUICK START GUIDE MODEL 485TC
MICROCOM
C O R P O R A T I O N
5
TEST
B4
INSTALL (FGL)
4A
INSTALL (WIN)
-FOR WINDOWS USE:
-GO TO “microcomcorp.com/products/485tc”
-SCROLL DOWN PRODUCT PAGE AND CLICK DOWNLOAD
-WINDOWS DRIVER” BUTTON
-UNZIP FILE AND FOLLOW README INSTRUCTIONS
-FOR FGL USE:
-GO TO “microcomcorp.com/products/485tc”
-SCROLL DOWN TO THE BOTTOM OF PAGE AND FIND THE
-DRIVERS TAB
-CLICK THE DOWNLOAD BUTTON FOR THE USB CDC DRIVER
-TO PRINT TEST TICKET WITH FGL, PRESS PRINT BUTTON ONCE
-TO PRINT TEST TICKET WITH WINDOWS DRIVER:
-GO TO “CONTROL PANEL” THEN “DEVICES AND PRINTERS”
-RIGHT CLICK THE 485TC AND SELECT PRINTER PROPERTIES
-CLICK “PRINT TEST PAGE”
3
LOAD
-LOOSEN GREEN THUMBSCREW AND ADJUST GREEN MEDIA
-GUIDES TO FIT PREFERRED MEDIA
-AFTER ADJUSTMENT, RETIGHTEN GREEN THUMBSCREW
-FEED MEDIA INTO MEDIA ENTRY SLOT (ONCE PRINTER DETECTS
-MEDIA, IT WILL AUTO FEED AND ALIGN PAPER)
CONNECT
-CONNECT POWER CABLE TO BACK OF PRINTER AND OUTLET
-CONNECT COMMUNICATION CABLE TO PRINTER PORT AND
-COMPUTER
-POWER ON THE PRINTER
ETHERNET | USB | RS-232 SERIAL
21
UNBOX
-PACKAGE SHOULD CONTAIN PRINTER, A POWER CORD, AND
-ANY OPTIONAL ITEMS YOU MAY HAVE PURCHASED
-STICKER ON BACK OF GUIDE WILL INDICATE MODEL TYPE

QUICK START GUIDE MODEL 485TC
MICROCOM
C O R P O R A T I O N
© Copyright 2019 MICROCOM Corporation. All rights reserved. Microcom Corporation reserves the right to make improvements to their products at any time without prior notice. The information contained herein is subject to change without notice.
Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. All company and product names are trademarks or registered trademarks of their respective owner.
3
DIAGNOSTICS
-TO ENTER DIAGNOSTIC MODE TO PRINT DIAGNOSTIC LABEL:
-INSERT MEDIA IN PRINTER
-TURN PRINTER OFF
-PRESS AND HOLD PRINT BUTTON
-WHILE HOLDING PRINT BUTTON IN, TURN PRINTER ON AND
-RELEASE PRINT BUTTON WHEN PRINTER PRINTS
-LABEL (10-12 SECONDS)
-FOR ADDITIONAL ASSISTANCE CONTACT:
-SALES: [e-mail]
-SUPPORT: [e-mail]
-SERVICE: [e-mail]
MICROCOM CORP.
[phone]
LABEL DIAGNOSTICS
Model: ### XX
Code: ##.##.##
Serial #: X######
CPU Serial #: X######
LangMode: #
Head Size (dots): ####
Head DPI (dots): ###
Life Pwr On (hrs): ##
Life Prntd Lbls: ###
Service Prntd Lbls: ###
Service Power On (hrs): ##
Life Prntd Inch: ###.##
Service Prntd Inch: ###.##
Serial ParamL ######, X, #, #
USB: XXXXXXX
USB MODE: XXX
ETH: XXXXXXXX
ETH DHCP: XX
ETH IP: XXXX
ETH SUBNET: XXXX
ETH GW: XXXX
ETH PORT: ####
ETH MAC: ##:##:#X:#X:##:X#
WIFI: XXX XXXXXXXXXX
2
SOLID GREEN: -INDICATES POWER IS ON AND IN READY STATE
SOLID RED: -INDICATES AN ERROR HAS OCCURRED
SOLID RED: -THE PRINTER WILL REMAIN IN THIS STATE
SOLID RED : -UNTIL THE CONDITION IS REMOVED*
SOLID AMBER: -PRINTER IN BOOT LOADER MODE
FLASHING RED: -MEDIA NOT DETECTED
FLASHING RED: -CUTTER ERROR
FLASHING RED: -UNSUCCESSFUL MEM. DOWNLOAD OPERATION
FLASHING RED: -POWER SPIKE
FLASHING RED: -LOW VOLTAGE ON AC LINE
FLASHING RED: -THE PRINTER WILL REMAIN IN THIS STATE
FLASHING RED: -UNTIL THE CONDITION IS REMOVED*
*IF ERROR PERSISTS, CONTACT YOUR SUPPORT REPRESENTATIVE
STATUS LIGHTS
FLASHING RED
SOLID AMBER
SOLID RED
SOLID GREEN
-FRONT
(A)
(B)
-BACK
(C)
(D)
(E)
(F)
(G)
(H)
(I)
(J)
(K)
(L)
(M)
STATUS LIGHT
PRINT BUTTON
EXTERNAL MEDIA ENTRY SLOT
CASH DRAWER PORT (OPTIONAL)
ETHERNET PORT
USB PORT
HOST USB PORT (FOR CODE UPDATES)
AUX PORT
ADJUSTABLE MEDIA GUIDES
RJ 12 SERIAL PORT (OPTIONAL)
RS-232 SERIAL PORT
POWER SWITCH
POWER CONNECTION
1
OVERVIEW
A
B
C
D
E
F
G
I
J
K
L
M
H