MicroImage Video Systems VDA124RM User manual

Page 4
IN CASE OF DIFFICULTY
If you are experiencing problems with any MicroImage product, you can
contact MicroImage Support using the following methods:
Phone [phone]
Fax [phone]
Email [e-mail]
Web www.mivs.com
WARRANTY
MicroImage Video Systems warrants that each VDA124RM/VDA212RM is free from
defects due to faulty materials or improper workmanship for a period of one (1)
year. MicroImage Video Systems further warrants that any part which proves
defective in materials or workmanship within one (1) year, will be replaced or
repaired at no cost to the user. Labor to replace defective parts will be done
without charge, provided the equipment is returned to MicroImage Video Systems
prepaid, insured and properly packaged. Prior return authorization must be
obtained from MicroImage Video Systems.
NOTE
This warranty covers the MicroImage VDA124RM/VDA212RM Video Distribution
Amplifiers only.
CONDITIONS
This warranty is void if the warranted part has been altered or subjected to abuse
or misuse. Defective parts must be returned to MicroImage Video Systems.
SOLE WARRANTY
This Warranty is in lieu of all other warranties expressed or implied including,
without limitation, any implied warranty or any implied warranty of fitness for a
particular purpose. MicroImage Video Systems shall have the final right to
determination as to the existence and cause of any defect and its appropriate
adjustment in accordance with the terms of this warranty. In no event shall
MicroImage Video Systems be liable for any consequential or collateral damages.
RETURNS
All returns MUST have an RMA number. Please call, fax or email for an
RMA form. The RMA form will have the proper shipping address for
returns.
Phone [phone]
Fax [phone]
Email [e-mail]
Rack Mount Video
Distribution Amplifier
Operation Manual
Model VDA124RM
Model VDA212RM
VDA124RM12-RoHS 24 Output Unit
VDA212RM12-RoHS Dual 12 Output Unit
Mic oImage Video Systems
division of World Video Sales Co., Inc
PO Box 331
Boyertown, PA 19512
Phone [phone]
Fax [phone]
[e-mail]
www.mivs.com

Page 2
CONTENTS
SPECIFICATIONS............................................................................2
UNPACKING ....................................................................................3
CONNECTIONS...............................................................................3
Power ...........................................................................................3
Video ............................................................................................3
LEVEL ADJUSTMENTS...................................................................3
IN CASE OF DIFFICULTY................................................................4
WARRANTY.....................................................................................4
RETURNS........................................................................................4
Rev 0 11-05-2009, Reviewed 07-07-2015
SPECIFICATIONS
Input level 1.0 Vpp Composite, 75 Ω
Output level Same as input into 75 Ω
Rear panel adjustable
Connectors BNC female
Bandwidth Greater than 30Mhz
Level Adjustment One each channel, +/ 25%
Temperature
Operating 0E - 40E C (32E - 104E F)
Storage 40E - 60E C ( 40E - 140E F)
Humidity
Operating 10% - 90% (non condensing)
Storage 5% - 95% (non condensing)
Power
Voltage +5VDc, +/ 5%
Consumption approximately 110mA
Power Module Included, 120VDC input, 50/60Hz, +5VDC output
Size 19.0" (W) x 2.0" (D) x 1.7" (H)
482.6 mm (W) x 50.8 mm (D) x 43.2 mm (H)
Weight 1.6 lb.
RoHS/Lead Free Compliant
Manufactured in USA by MicroImage Video Systems
Page 3
UNPACKING
The VDA124RM/VDA212RM package includes the following items:
VDA124RM or VDA212RM Video Distribution Amplifier
+5VDC Power Supply Module
75 ohm 1% Termination ( two for VDA212RM)
This operation manual
Please inspect all items carefully and report damaged or missing items to
your dealer or MicroImage Video Systems.
CONNECTIONS
Powe
The VDA124RM/VDA212RM uses an external DC power supply to provide
power to the unit. It can also be run from a regulated +5VD (+/ 10%)
power source. Connect the small plug from the power module to the
power connector on the rear of the VDA unit. Plug the power module into
a suitable power source of 120VAC, 50 60Hz (USA units).
Video
Connect the video source (i.e. camera) to the IN connector on the VDA
unit. A 75 ohm termination (supplied) should be placed on the unused
Loop BNC, or on the last unit in the chain if connecting multiple units
together.
Connect the OUTPUT signals from the VDA unit to the video displays or
other equipment as required. Each output must only have a single 75
ohm termination. The VDA124RM has one set of inputs for all 24RM
outputs while the VDA212 has two sets of inputs, each driving a row of 12
outputs. The VDA124RM/VDA212RM uses female BNC connectors.
LEVEL ADJUSTMENTS
Each row of outputs (12) has a level adjustment accessible via the rear
panel. For the VDA124RM, each adjustment affects the top or bottom row
of output connectors aligned with the adjustment. For the VDA212RM,
each adjustment affects it=s respective channel aligned with it.
Adjustments can be made via a small flat blade screwdriver.