MicroNet SP5821 User manual

User’s Manual
1080p Full HD WDR IR Indoor
Fixed Dome IP Camera
Model No.: SP5821
Version: 1.0

2
Welcome
Thank you for purchasing this network camera. The camera adopts the Progressive
Scan technology with low-bit-rate video compression, providing the high image
resolution, outstanding picture quality, real time performance, and clear image under
motion for your surveillance solution.
The camera comes with a browser-based configuration utility that allows you to
integrate it into your network easily. It also provided the computer utilities that allow
you to search and manage the camera installed within your network (after the utilities
are installed on your computer).
With the trouble-free hardware installation, user-friendly management utilities and
comprehensive applications supported, the camera is your best choice for remote
monitor, high quality, and high performance video images.
Important information for using the manual
This manual has been prepared to guide you through the operation of your camera
from first set-up through to continuous use, which includes:
Chapter 1. Knowing your camera
You will know the components and functions of the camera.
Chapter 2. Hardware and Software Installation
Helps you install the camera according to your application. You will be able to set up
the camera at home, at work, at any where you want.
Chapter 3. Managing the Camera
Helps you operate and manage your camera without trouble.
Appendix: Provides the specification and general information of the camera.
It is important to understand the terms and typographical conventions used in this
manual. The following kinds of formatting in the text identify special information:
Bold — indicates the items displayed on the screen, including buttons, headings,
field names and options. Example: click the Browse button to locate the firmware
file.
Italics — indicates the name of a screen. Example: the Network Setting screen of
the Configuration Utility.
Please read this manual carefully before using your camera for the first time. Keep this
manual in a safe place and use as your first point of reference.

3
Disclaimer
The manufacturer operates a policy of ongoing development. The manufacturer
reserves the right to make changes and improvements to any of the products
described in this document without prior notice. The manufacturer does not warrant
that this document is error-free.
Not all models are available in all regions. Depending on the specific model purchased,
the color and look of your device and accessories may not exactly match the graphics
shown in this document.
The screenshots and other presentations shown in this manual may differ from the
actual screens and presentations generated by the actual product.
All such differences are minor and the actual product will deliver the described
functionality as presented in this User Manual in all material respects.
Copyright
All brand and product names are trademarks or registered trademarks of their
respective companies.
Revision: 1.0
(04/2012)

4
Contents
Welcome ................................................................................................. 2
Important information for using the manual......................................... 2
Disclaimer ............................................................................................ 3
Copyright ............................................................................................. 3
Contents .................................................................................................. 4
Chapter 1. Knowing Your Camera .......................................................... 5
Package contents ................................................................................ 5
Camera components and functions..................................................... 6
System requirements........................................................................... 8
Camera features.................................................................................. 8
Chapter 2. Hardware and Software Installation ...................................... 9
Installing the camera Hardware........................................................... 9
Connecting the cables ....................................................................... 10
Applications of the Camera ............................................................... 12
Installing software.............................................................................. 13
Chapter 3. Managing the Camera......................................................... 14
Setting up the camera’s networking by setup wizard ........................ 14
Accessing the camera’s Configuration Utility .................................... 15
Using the Configuration Utility ........................................................... 16
Network Setting ................................................................................. 17
Audio/Video Setting ........................................................................... 21
Event Setting ..................................................................................... 22
System Setting................................................................................... 28
Record ............................................................................................... 31
Advance Setting ................................................................................ 34
System Status.................................................................................... 36
Firmware Upgrade............................................................................. 37
Reboot ............................................................................................... 38
Appendix ............................................................................................... 39
Specifications..................................................................................... 39
Configuring the IP Address of the computer ..................................... 40

5
Chapter 1. Knowing Your Camera
Package contents
Check the following items that are included in the package. Contact the authorized
dealer of your locale immediately if any item contained is damaged or missing.
One network camera
One 4-pin Power Terminal Block
One 4-pin DI/DO Terminal Block
One RJ-45 Female to Female Connector
One Installation CD
One Quick Installation Guide
One DC power adapter (Optional)

6
Camera components and functions
1. Plastic cover
To remove the plastic cover by fitting little tools (e.g. coin, tweezers.. ) into the
groove on the side of the camera and then twist open the cover.
2. Infrared LED
The four infrared LEDs around the lens assembly allow your camera to capture
clear mage in a dark environment
3. Lens assembly
The lens assembly is equipped with a focus/zoom function, allowing you to adjust
the focus/zoom manually to capture clear image.
4. Light sensor
The light sensor enables/disables the infrared LEDs by detecting the light
condition.

7
5. Ethernet port
The port is used to connect the camera to your network via the Ethernet cable
(RJ-45 type). The port supports the NWay protocol so that the system will be able
to detect the network speed automatically.
The port on the PoE model is compliant with IEEE802.3af PoE (Power over
Ethernet) standard. The camera can be powered on by the Ethernet cable so that
you can install the camera anywhere without a power outlet supported.
6. Audio Out (Green)
The audio output connects an external active speaker
7. Audio In (Red)
The audio line input allows you to connect an external microphone.
8. Reset/ DC 5V power input (Red)
The power input connects the DC power adapter to supply power to the camera
Pin1: +5V
Pin2: -5V
Pin3: Reset (In order to restore the factory default settings for the camera, creating
a short circuit by using a metal tool to connect Pin3 and Pin4 simultaneously for 5
seconds)
Pin4: Ground
9. DI/DO terminal (Black)
The terminal allows camera to send and receive signal to external device.
Pin1: DI (Digital Input)
Pin2: Ground
Pin3: DO (Digital Output)
Pin4: X (no use)
10. MicroSD card slot (Inside Camera)
The slot allows you to insert a memory card for expansion of storage.
Remove back cover of the camera. Hold the MicroSD card by the edges and gently
insert it into the slot. To remove a card, gently push the top edge of the card
inwards to release it and then pull it out of the slot.

8
System requirements
When the camera is installed in your network for remote surveillance applications,
ensure the computer is in good network connection and meet system requirements as
below:
Minimum system requirement for connecting one camera
CPU: Pentium 4 class, 2.0GHz
Memory: 512MB RAM
Hard disk drive: 500MB of available space
GPU: AGP card, 128MB RAM; resolution @ 800x600 or above
Operating system: Microsoft Windows XP, Vista, and Win 7
Browser: Microsoft Internet Explorer 7.0 and above
Recommended system requirements for connecting multiple cameras
CPU: Intel Core 2 Duo, 2.0GHz
Memory: 2GB RAM or more
Hard disk drive: 500MB of available space
GPU: High performance graphic card, 256MB RAM or more; resolution @
1024x768 or above
Operating system: Microsoft Windows XP, Vista, and Win 7
Browser: Microsoft Internet Explorer 7.0 and above
Note: When you connect multiple cameras to monitor different places within your
surveillance application, it is recommended to use high-performance computer and
networking to approach better effect while transmitting the image.
Camera features
Capture high resolution video with the 2 mega-pixel CMOS sensor.
Real-Time dual streams.
30ftps @ 720P or 1080P.
True Day/Night function
Built-in IR LED, varifocal 3.3~12mm/F1.2 Lens
H.264, Mpeg4 and MJPEG compression supported.
Motion detection supported.
Two-way audio
Compliant with IEEE802.3af standard, allowing the camera to be powered by the
Ethernet cable.
Firmware upgradeable through the browser-based Configuration Utility.

9
Chapter 2. Hardware and Software
Installation
Installing the camera Hardware
The camera is designed to be mounted on the ceiling. Use drill template, drill
two holes that correspond to the two screw holes on the bottom of the
camera.
Mount the camera stand
throu
g
h the two screw holes
Bottom view of the camera

10
Hold the camera against the ceiling, secure it with two screws, insert MicroSD
card into the MicroSD card slot; and then you can adjust the camera lens to
any target place of object.
Connecting the cables
Connecting the Ethernet cable
Use the RJ-45 type Ethernet cable to connect the camera to your local area
network (LAN).
Plug one end of the Ethernet cable to the Ethernet port on the bottom panel of the
camera and the other end to an active port on the switch/router of the network.
Connecting the DC power adapter*
If the switch/router is POE compliant, this step can be ignored. Please jump to next
step.
Plug the 5V DC power adapter with the 4-pin terminal block to the DC power input and the
power plug to the wall socket. (Optional for non-PoE environment.)
Secure the camera into
ceilin
g
with two screws
Insert MicroSD Card

11
Connect to external device*
If there is any external device needed to work with camera, connect them to DI or
DO terminal.
Connecting the Ethernet
cable
Connecting the power
ada
p
te
r
Router

12
Applications of the Camera
The camera installed in your network can be applied in multiple applications, including:
Monitor different places, such as bank, airports, factories, entrances, hall ways and
parking lots, and objects remotely via the Internet or Intranet.
Capture still images and record video clips.
Alert function that includes FTP upload and email messages.
The following explains how to set up the camera in the network and how does it work
in your surveillance applications.
Router/ Switch

13
Installing software
The Camera Setup Wizard, IPSearchUtility2 comes with your camera is a
conveniently utility to search the connected camera within the network from your
computer.
To install the utility on your computer:
1. Insert the Installation CD into the computer’s CD-ROM/DVD-ROM drive.
2. The CD Menu should pop up automatically. Go into
"Software/Utility" and double click "IPSearchUtility2" to initiate the
setup. Follow the prompts to complete the installation.
3. When done, the IPSearchUtility icon will display on the desktop. Double-click on
the icon to launch the utility.
4. From the Control Panel, you can:
Check the connected camera(s) from the Camera List, such as the IP Address,
Camera Name, Mac Address, and more.
Click Wizard to change the IP address of the selected camera.
Click Scan to search the camera within the network.
Click Connect IE to access the camera using Internet Explorer.
Click Exit to end the utility.

14
Chapter 3. Managing the Camera
Setting up the camera’s networking by setup wizard
IPSerachUtilty2 lets you configure your camera’s networking easily and quickly. The
wizard will guide you through the necessary settings step-by-step.
1. Launch IPSerachUtilty2 on your computer.
2. Select the camera you want and then click Wizard.
3. When prompted, enter the User Name and Password to access the camera. The
default User name is “root” and the default password is “pass”.
4. Follow the prompts to complete the networking settings for the camera, including:
select networking type (DHCP or Static IP)
configure wireless network (for wireless model only)
The diagrams below explain the wizard briefly:
5. When done, re-connect the Ethernet cable and then click Scan again from the
wizard’s Control Panel.
Select networking type
DHCP
Static IP
For wireless model
Click Finish to

15
Accessing the camera’s Configuration Utility
You can manage the camera via the computer’s Web browser easily. The following
sections will guide you through the basic and advanced settings of the camera by
using the browser-based Configuration Utility.
1. You can access the camera through IPSearchUtility2 or via Internet Explorer:
Access from IPSerachUtilty2
Launch IPSerachUtilty2. From the Camera List, select the desired camera and
then click Connect IE.
Tip: To learn more of using Camera Setup Wizard, see the “Installing
software” section in Chapter 2.
Access from Internet Explorer
Launch Internet Explorer. Enter the camera’s IP address in the URL bar of the
browser and then press ENTER. The default IP address of the camera is
“192.168.1.2”.
2. Enter the User name and password in the Login window. The default User name
is “root” and the default password is “pass”.
Note: If you are the first time to access the camera, it may be required to install a
plug-in for the camera. Permission request depends on the Internet security
settings of your computer. Follow the prompts to complete the plug-in installation.
3. When you access the camera’s Configuration Utility, the Main screen will appear
as below:

16
Using the Configuration Utility
The Main screen of the Configuration Utility provides you with many useful information
and functions, including the menus on the left column, the control buttons on the top of
the screen, and the Live View area for displaying the real-time video image. You can
also change the display language from the Language drop-down menu.
The menus
The menus contain the basic and advanced settings of the camera. Click the
desired button to display the menu screen.
Menu Description
Live View — Display the real-time video image of the connected
camera on the Main screen.
Network Setting — Change the network settings of the camera,
such as LAN, PPPoE, DDNS, and more.
Audio/Video Setting — Change the audio and video settings of the
camera.
Event Setting — Complete the required settings so that you can
upload images to FTP and send email messages by events.
System Setting — Change the camera’s basic settings. For
example, change the displayed camera name.
Record — Change the settings for recording.
Advance Setting — Set the schedule profile and DI/D for the
camera.
System Status — Display the current configuration of the camera.
Firmware Upgrade — Upgrade the latest firmware (if available) for
your camera.
Reboot — Restart the camera.
The control buttons
The control buttons allow you to control the camera’s function from the screen.
Button Description
Stream Change the stream to Master or Slave.
Snapshot Capture and save a still image*.
*The folder that stores the captured image will be displayed on the screen for 2
seconds after you click the Snapshot button.

17
Network Setting
LAN
This sub-menu allows you to select the IP address mode and set up the related
configuration.
- Ethernet Interface:
Select the Use DHCP option when your network uses the DHCP server. When
the camera starts up, it will be assigned an IP address from the DHCP server
automatically.
Otherwise, select the Use fixed IP address option to assign the IP address
for the camera directly, including IP Address, Subnet Mask, Gateway, DNS1,
and DNS2.
Option Description
IP
Address
Enter the IP address of the camera. The default setting is
“192.168.1.2”.
Subnet
Mask Enter the Subnet Mask of the camera. The default setting is
“255.255.255.0”.
Gateway Enter the default Gateway of the camera. The default setting is
“192.168.1.1”.
DNS1/2 DNS (Domain Name System) translates domain names into IP
addresses. Enter the DNS1 (Primary DNS) and DNS2
(Secondary DNS) that are provided by ISP (Internet Service
Provider).
When done, click Save.
PPPoE

18
This sub-menu is used when you use a direct connection via the ADSL modem.
Select the Enable option to enable this feature.
To activate PPPoE mode, you should have a PPPoE account from your Internet
service provider. Enter the User Name and Password (twice). The camera will get
an IP address from the ISP as starting up.
When done, click Save.

DDNS
This sub-menu allows you to assign a fixed host and domain name to a dynamic
Internet IP address. Select the Enable option to enable this feature.
Note: You need to sign up for DDNS service with the service provider before
configuring this feature and accessing the server.
To set up the DDNS:
b. Select the DDNS Service type.
c. Select the Interface.
d. Enter the required information in the Host Name, User Name, and Password
options.
e. When done, click Save.

19
NTP
This sub-menu lets you set the correct date and time for the camera.
- Synchronized with Time Server:
Select the option and the time will be synchronized with the NTP Server. Then,
select the proper Time Zone for the region from the drop-down menu and
enable or disable Daylight Saving.
- Manual Update:
You can also enter the date and time manually by selecting the option.
- Synchronized with PC:
Select the option and the date/time settings of the camera will be synchronized
with the connected computer.
When done, click Save.

20
UPnP
This sub-menu allows you to enable of disable the UPnP function for the camera.
Select the Enable option to enable this function.(Default is set to Enable)
The UPnP (Universal Plug and Play) function is a set of computer network
protocols that enable the device-to-device interoperability. It also supports port
auto mapping function so that you can access the camera if it is behind an NAT
router or firewall.
- Discovery Available:
Select the option and the camera will be able to announce to control points that
it has become available on the network.
- NAT Traversal:
Select the option if the camera is located behind a router used a NAT network
technology, and the router supports NAT Traversal function, user might enable
camera to negotiate with the router about the port configuration via this
function.
When done, click Save.