MicroVision MV-1104-001 User manual
USER GUIDE
MV-1104-001
PicoP®Display Technology
Assessment Unit
MV-1104-001
PicoP®Display Technology Assessment Unit
The MV-1104-001 is part of MicroVision’s demonstration platform
for PicoP®display technology, a display engine solution based on
MicroVision’s proprietary laser beam scanning technology.
This assessment unit is a prototype produced by MicroVision to
demonstrate the image quality and basic functionality possible from a
mobile projector that incorporates PicoP®display technology. It is not
intended to represent a consumer-ready mobile projector.
Finished form factor, industrial design, run time, user interface, auxiliary
features, and any other commercial product considerations should be
addressed as part of bringing a product to market to suit target audiences
and differentiation requirements.
5 1 2 3 4
6
MV-1104-001 KEY
1Micro-HDMI/MHL Port
2Micro-USB Port
3Power Button
4LED Indicators
53.5mm Audio Jack
6Thread for Mounting
IN THE BOX
1. MV-1104-001 Assessment Unit
2. USB Stick
a) Electronic User Guide
b) Demonstration Content
3. USB to Micro-USB Cable
4. HDMI to Micro-HDMI Cable
5. User Guide
DIRECTIONS
Power On/Off:
1. Press and hold the power button 3for 1.5 seconds.
(The LED indicator light will start blinking blue)
2. The screen will display black with an “Image by PicoP®” splash screen.
The unit is ready to connect.
3. The operating time of the unit on a fully charged battery is ~3 hours.
4. To power off press and hold the power button 3until the LED
indicator light turns off.
Connecting to the Assessment Unit:
1. Turn on the Assessment Unit and wait for the “Image by PicoP®”
splash screen.
2. Connect the desired host device via the appropriate connection
adaptor and/or cable as specified in the Connection Matrix found at
www.microvision.com/eval_platform
3. Your content should begin projecting. Selected demonstration content
is available on the USB stick included with this unit and online at
www.microvision.com/eval_platform
Charging:
1. Connect the standard USB to Micro-USB cable provided with the unit
to the Micro-USB port 2on the unit. (USB 5v). The LED indicator light
should be solid amber to indicate charging. It will become solid green
when a full charge is reached.
2. For extended operation, the unit can be run when connected to power
via the USB charging cable.
LED Indicator Light Key:
Blue Flashing – unit active
When connected to external power:
Solid Amber – unit charging
Solid Green – fully charged
Audio:
Internal speaker
3.5mm audio jack 5for headphones or external speaker.
Category Characteristic Specification
Display
Performance
Resolution Input: 1280x720p Output: 1920x720
Brightness 40 lm
Light Sources Red 639nm, Green 522nm, Blue 445nm
Refresh Rate 60Hz
Color Bit Depth 16.78M colors (R/G/B=8/8/8bit)
Sequential Contrast 80,000:1
Projection Lens No focusing lens
Focus Range Always in focus
Aspect Ratio 16:9
Throw Ratio 1.3
Mechanical
Parameters
Dimensions (H x W x L) 11 x 75 x 131.5 mm
Weight 155g
Audio Built in speaker
3.5mm audio jack
1w; Auto Switch from speaker to
external headphone/speaker plugged
into the audio jack
Video Interface Micro-HDMI/MHL Auto Switch between HDMI and MHL
Power Internal rechargeable battery Micro-USB for charging
2500mAh battery
Run time 3 hours
Temperature Operating 0 to 35 degrees Celsius
Storage -30 to +70 degrees Celsius
Regulatory Compliance Laser Safety Classification Class 3R Laser Product
IEC60825 Edition2
SPECIFICATIONS MATRIX
SERVICE AND SUPPORT
For questions and support please contact MicroVision Customer Service
by
e-mail at customerservice@microvision.com
Some answers and the latest connectivity information are available at
www.microvision.com/eval_platform
Engineering and development support are not included with the purchase
of the MV-1104-001. If you need expanded support services beyond
basic troubleshooting, please contact your MicroVision Business
Development representative.
WARRANTY
A copy of the warranty for the MV-1104-001 is included in the box.
It is also available on the Evaluation Platform Portal at
www.microvision.com/eval_platform
LASER SAFETY
Information regarding laser safety is included in the box. It is also available
on
the Evaluation Platform Portal at www.microvision.com/eval_platform
© Copyright 2015, MIcroVision, Inc. All rights reserved.
®PicoP is a registered trademark of MicroVision, Inc.
All other trademarks are property of their respective owners.
DA0134215
