Middle Atlantic Products UPS-IPCARD User manual

QUICK INSTALLATION GUIDE
UPS Network Interface Card
UPS-IPCARD
Intelligent UPS Network Interface Card allows a UPS
system to be managed, monitored, and configured
remotely via the web
INSTALLATION GUIDE
5. Connect the Ethernet cable
to the LAN port of the
Middle Atlantic UPS
Network Interface Card.
6. Turn on the UPS.
4. Re-install and tighten the
retaining screws.
3. Install the Middle Atlantic
UPS-IPCARD into
the expansion port.
2. Remove the two retaining
screws of the expansion port
cover then remove the cover.
1. Turn off the UPS before
removing the expansion port
cover on the UPS.
LED Indicators
Step 2. Configure the IP address for the Middle Atlantic
Network Interface Card.
Method 1: Using the SNMP Card Configuration Tool
1. Install the SNMP Card Configuration Tool from the included CD. It is
located on the CD in the \tools\network folder. Double click the
installation file “MAP_SNMP_Setup.msi” to begin the installation.
2. After the installation is complete, run the “Middle Atlantic UPS-IPCARD
Setup Utility” program. Under “All Programs”, select “Middle Atlantic
Products > UPS-IPCARD”.
3. The main screen of the SNMP Card Configuration Tool program is
shown in Figure. 1. The configuration tool will display all Middle Atlantic
UPS Network Interface Cards present on the network. Click "Refresh" to
search for newly added devices
4. Select the SNMP card you are setting up. Click on the Tools menu and
select “Device Setup” or double click the SNMP card you want to
configure.
5. You can modify the IP
Address, Subnet Mask, and
Gateway address for the
Device MAC Address listed in
the Device Network Settings
window, as shown in Figure 2.
The default IP Address is
192.168.20.177, the default Subnet
Mask is 255.255.255.0.
6. To modify the IP, subnet mask
or gateway address, enter
the new addresses into the
corresponding fields and click
Save.
Link LED color
Off
On(Yellow)
RX/TX LED color
Off
On(Green)
Flashing
Condition
The UPS Network Interface Card is not
connected to the Network or the UPS
Network Interface Card power is off
The UPS Network Interface Card is connected
to the Network
The UPS Network Interface Card power is off
The UPS Network Interface Card power is on
- Receiving/transmitting data packet
- Reset completed
RX/TXLink
Ethernet connector
LINK Indicator
RX/TX Indicator
Figure 1. The main window of the “Setup Utility” program.
Figure 2. The SNMP card setting window.
Step 1. Hardware Installation
I-00434 Rev A

7. You will need to enter a
User Name and Password
for the SNMP card in the
authentication window, as
shown in Figure 3.
*Default user name: admin
Default password: admin
8. If the IP address is
successfully set, you will
see a message that the IP
set up is OK, as shown in
Figure 4.
WEB INTERFACE Login Account
There are two user account types.
- Administrator (default username : admin ; default password : admin)
- Viewer (default username : guest ; default password : guest)
The administrator can access all functionality including enable/disable the guest account. The guest account can access “read only” functionality but can not
control or change any settings.
Figure 3. Authentication window.
Figure 4. Setup IP Address successfully message.
Troubleshooting
Problem
Unable to configure
the UPS Network
Interface Card by
method 1 or
method 2
Unable to ping the
UPS Network
Interface Card.
Forgotten the user
name and password
Solution
1. Check the LED status, the normal condition is
both yellow and green led is on.
If green led is off:
►Check if the UPS Network Interface Card is
properly seated in the UPS and the UPS
power is on.
If yellow led is off:
►Check if the network connection is valid
2. Check if the operated PC is on the same
physical network as UPS Network Interface
Card is.
1. Use method 1 and method 2 to get correct IP
address of the UPS Network Interface Card.
2. If the operated PC is on the different physical
network from the UPS Network Interface
Card, verify the setting of subnet mask and
the IP address of gateway.
Please refer to the “Reset to Default Setting /
Recover from a Forgotten Password”
section in the user manual.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
admin
Method 2: Using a command prompt
1. Obtain the MAC address from the label located on the top of the UPS
Network Interface Card printed circuit board. Each UPS Network
Interface Card has a unique MAC address.
2. Use the ARP command to set the IP address.
Example:
To assign the IP Address 192.168.20.240 for the UPS Network
Interface Card, which has a MAC address of 00-0C-15-00-00-01 you
will type in the following command prompt from a PC connected to the
same network as the UPS Network Interface Card.
(1) Type in “arp-s 192.168.20.240 00-0C-15-00-00-01” then press
Enter.
3. Use the Ping command to assign a size of 123 bytes to the IP.
(1) Type in “ping 192.168.20.240 -1 123” then press Enter
(2) If the replies are received, your computer can communicate with the
IP address.