Middle atlantic products Tor-x-20rp User manual

I-00106 Page 1 Rev E

TOR SERIES

TOR-X-20RP

Flush Mount tilt out wall rack

Instruction Sheet

THANK YOU

Thank you for purchasing the TOR-X-20RP Flush Mount. Please read these

instructions thoroughly before installing / assembling this product.

PRODUCT FEATURES

- Convenient tip-out design allows easy access to equipment controls

- Rackrail is included for use with rackmount equipment

- Mount non-rackmount equipment using included clamp bars

C US

LISTED

Page 2

I-00106

TOOLS:

- Socket wrench set

- Power drill and bit set

1) Construct a rough opening - 24.75" W x 30.312" H:

2 space - 2 x 4

3 space - 2 x 4 for partial, 2 x 6 for flush

4 space - 2 x 4, 2 x 6 for partial, 2 x 8 for flush

2) Disassembly is required prior to mounting.

Open the door on the faceplate. To do this, the

door must be slightly lifted and opened to the service

4) Using the customer supplied mounting hardware

specified below, mount the backpan into the wall.

(FIGURE C)

Block Wall Installation:

1) 5/8" pilot hole

2) 1/4" X 2" toggle bolt and washer

Wood Stud Wall Installation:

1) 1/8" pilot hole in center of stud

2) 1/4" X 2" lag bolt and washer

5) Re-assemble the faceplate to the backpan by re-using

the six nuts. (FIGURE B)

3) Remove the six nuts that secure the

faceplate to the backpan and remove

the faceplate. (FIGURE B)

NOTE: If using with the partial recess trim

kit (TOR-PRT), see Instruction Sheet

I-00107. (optional accessory)

LIFT

ROTATE

FIGURE A

MOUNTING

HOLES

FIGURE C

FIGURE B

FACE

PLATE

BACKPAN

CLAMP

UCP

PANEL

DECORA STYLE

KNOCKOUT

ASSEMBLY

position (1050). (FIGURE A)

I-00106 Page 3

FIGURE D

CLAMP ASSEMBLY:

NOTE: Middle Atlantic Products provides a clamp for use on non-rackmount equipment. On

equipment that is rackmounted, the clamp is not required and can be discarded.

Choose a desired location for the clamp and assemble the clamp to the ears using the screws

and nuts provided (FIGURE D). Slide the clamp brackets securely down on the equipment and

tighten. Adjust the stop bars to secure the rear of the equipment and tighten.

CONNECTION OF THE BONDING WIRE:

Install the bonding wire as

shown using the wire and

the nuts provided.

EARS

CLAMP

BRACKETS

STOP

BARS

OPTIONAL ACCESSORY: UNIVERSAL CONNECTOR PANEL

For Middle Atlantic Products UCP modules (used to mount commonly used connectors), see

middleatlantic.com for details. To install, remove the blank panel and install re-using hardware

provided.

NOTE: Some of the UCP panels may need to be mounted on the

surface of the faceplate.

I-00106 Page 4

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the TOR-X-20RP Flush Mount to be free

from defects in material or workmanship under normal use and conditions for the lifetime of

the product.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and

exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return

of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the

products purchased, or any part or parts thereof, which the Company has determined to be

defective after inspection thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by

parties other than the Company, or any modification or alteration of the products. In addition, this

warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY

BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE

PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)

HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS

PAID TO THE COMPANY.

Corporate Headquarters

Corporate Voice 973-839-1011 - Fax 973-839-1976

International Voice +1 973-839-8821 - Fax +1 973-839-4982

middleatlantic.com - [email protected]

Middle Atlantic Canada

Voice 613-836-2501 - Fax 613-836-2690

middleatlantic.ca - [email protected]

Factory Distribution

USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 Registered Company

30% Recycled Paper

TOR SERIES

TOR-PRT Partial Recess Trim Kit

For Tilt Out Wall rack

Instruction Sheet

I-00107 Page 1 Rev D

The assembly should coincide with initial installation

of the product. (Instruction Sheet I-00106)

NOTE: The flange from the faceplate should be removed. Take out the six (6) screws from the

back of the faceplate and remove.

1) Place the fascia on the backpan and slide on the backpan until it is flush with the wall.

(fascia will be sandwiched between the side of backpan and the wall stud)

2) Install the six (6) customer supplied mounting screws through the backpan side and

fascia, do not tighten. (FIGURE A)

3) While pressing on the fascia face until it’s completely flush with the wall, tighten the

mounting screws.

TIP: Tighten the alternate corners first, followed by the center screws.

FIGURE A

FASCIA

BACKPAN

NOTE: The trim provides aesthetic improvements

when used on partially recessed

applications.

TOOLS REQUIRED

# 2 Phillips Driver

C US

LISTED

ASSEMBLY

I-00107 Page 2

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the TOR-PRT Partial Recess Trim

Kit to be free from defects in material or workmanship under normal use and conditions for the

lifetime of the product.