Middle Atlantic Products AXS User manual

I-1000 Rev L
AXS/ AX-SX / SAX / SSAX
Equipment Access System
Instruction Sheet
THANK YOU
Thank you for purchasing the Equipment Access System. Please read these instructions
thoroughly before installing and assembling this product.
PRODUCT FEATURES
• Allows an entire bay of heavy equipment to pull out on removable service tracks.
• Detachable rack frame allows off-site equipment integration.
• Articulating cable carriers attach to rack frame for effective cable management.
• Rolling rack frame retracts into millwork.
• Usable rack frame heights from 10 spaces (17-1/2") to 43 spaces (75-1/4") for
AX-SX & SSAX systems and 15 spaces (26-1/4") to 43 spaces (75-1/4") for
AXS and SAX systems.
• Rack frame 26" deep for AXS-xx-26, 20" deep for AXS and AX-SX systems,
16" deep for SAX & SSAX systems.
• 650 lb. capacity with proper weight distribution.

1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.

IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING ALERTS YOU TO A SITUATION
THAT COULD RESULT IN SERIOUS PERSONAL INJURY
OR DEATH.
!
!
IMPORTANT WARNINGS AND CAUTIONS!
WARNING! FAILURE TO READ, UNDERSTAND AND
FOLLOW THE FOLLOWING INFORMATION CAN
RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO
THE EQUIPMENT OR VOIDING OF THE WARRANTY. IT
IS THE RESPONSIBILITY OF THE INSTALLER/USER TO
ENSURE THAT THIS PRODUCT IS LOADED
ACCORDING TO SPECIFICATIONS.
WARNING! THE WEIGHT RATINGS OF THIS PRODUCT
CAN BE FOUND ON THE PRODUCT. EXCEEDING
THESE WEIGHT RATINGS CAN RESULT IN SERIOUS
INJURY OR DAMAGE TO THE EQUIPMENT. IT IS
THE RESPONSIBILITY OF THE INSTALLER/USER TO
ENSURE ALL COMPONENTS INSTALLED DO NOT
SURPASS THE WEIGHT RATINGS AS AN UNSTABLE
CONDITION CAN OCCUR WHICH MAY CAUSE
POSSIBLE INJURY OR DAMAGE.
!
!
NOTE: A NOTE is used to highlight procedures pertaining
to the installation, operation or maintenance of the product.
CAUTION! SAFETY MEASURES MUST BE PRACTICED
AT ALL TIMES DURING THE ASSEMBLY OF THIS
PRODUCT. USE PROPER SAFETY EQUIPMENT
AND TOOLS FOR THE ASSEMBLY PROCEDURE TO
PREVENT PERSONAL INJURY.
!
CAUTION: A CAUTION ALERTS YOU TO A SITUATION
THAT MAY RESULT IN MINOR PERSONAL INJURY OR
DAMAGE TO THE PRODUCT AND / OR PROPERTY.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Only use attachments/accessories specified by the manufacturer.
CAUTION! FOR LOADING, ALWAYS PUT HEAVIER
ITEMS AT THE BOTTOM OF THE BAYS, NOT NEAR THE
TOP, IN ORDER TO HELP PREVENT THE POSSIBILITY
OF THE FURNISHING TIPPING OVER.
!
CAUTION! THE APPLIANCE IS NOT INTENDED FOR
USE BY YOUNG CHILDREN OR INFIRM PERSONS
WITHOUT SUPERVISION.
!
CAUTION! IF THERE IS VISIBLE DAMAGE ON THE
PRODUCT IT MUST NOT BE INSTALLED.
!
CAUTION! NOTE THAT DURING CONSTRUCTION OF
THE CONSOLE, THERE MUST BE NO POSSIBILITY OF
PERSONAL INJURY, FOR EXAMPLE THE SQUEEZING
OF FINGERS OR ARMS.
!
Page 3
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.

Important Safety Instructions....................................................................................... 3
Rough-In / Site Preparation......................................................................................... 4
Millwork Specifications.............................................................................................. 4
Rough-In Pan Assembly.......................................................................................... 5
Millwork Specifications.............................................................................................. 6
Rough-In Pan Assembly............................................................................................ 7
Rough-In Pan Assembly (Continued)...............................................................................8
Rack Assembly...................................................................................................... 9
Rack Assembly (Continued).........................................................................................10
Rack Assembly (Continued).........................................................................................11
Service Stand / Service Track Assembly........................................................................... 12
Rack and Cable Carrier Installation................................................................................ 13
Cable Management................................................................................................. 14
Securing Rack Assembly In Millwork............................................................................... 14
Gasket Kit (Optional) Installation................................................................................... 15
Guide Kit (Optional) Installation.....................................................................................15
Warranty............................................................................................................. 16
Page 4
TABLE OF CONTENTS

Page 5
1) Rough-in millwork must be plumb, square and completed
before beginning assembly. Minimum millwork mounting
dimensions (without gasket and guide kit) are as follows: DID YOU KNOW?
Optional gasket (part # BG-17)
fills gap between rack and millwork.
Optional gasket and guide kit helps
keep rack centered and protects
millwork. Order part # AXS-GG16,
AXS-GG20 or AXS-GG26 for 16", 20"
or 26" depth racks, respectively.
19" min.
(SAX & SSAX)
22-1/2" min.
(AXS & AX-SX)
28-1/2" min.
(AXS-xx-26)
"A" "B"
3" minimum
40" maximum
17" for use with
AX-SX & SSAX
28" for use with
AXS, SAX &
AXS-xx-26
1/2" min.
set back
2-1/2" max. TRACK25 - 24-1/2" max.
TRACK50 - 49-1/2" max.
NOTE: Total rack height including rough-in pan is the usable rack height ("A") plus 4-9/16."
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.
ROUGH-IN / SITE PREPARATION
MODEL DEPTH
22-1/2”
22-1/2”
28-1/2”
WIDTH
19-1/4”
19-1/4”
19-1/4”
SAX / SSAX*
AXS / AX-SX*
AXS-xx-26*
*Setback is 1/2” for all models
NOTE: When using optional gasket and guide kit, minimum rough millwork opening width is 19-5/8".

Page 6
NUMBER OF
USABLE
RACK SPACE
“A” (INCHES)
USABLE
RACK HEIGHT
“B” (MIN. INCHES)
ROUGH
OPENING HEIGHT
17-1/2
19-1/4
21
22-3/4
24-1/2
26-1/4
28
29-3/4
31-1/2
33-1/4
35
36-3/4
38-1/2
40-1/4
42
43-3/4
45-1/2
47-1/4
49
50-3/4
52-1/2
54-1/4
56
57-3/4
59-1/2
61-1/4
63
64-3/4
66-1/2
68-1/4
70
71-3/4
73-1/2
75-1/4
22-3/16
23-15/16
25-11/16
27-7/16
29-3/16
30-15/16
32-11/16
34-7/16
36-3/16
37-15/16
39-11/16
41-7/16
43-3/16
44-15/16
46-11/16
48-7/16
50-3/16
51-15/16
53-11/16
55-7/16
57-3/16
58-15/16
60-11/16
62-7/16
64-3/16
65-15/16
67-11/16
69-7/16
71-3/16
72-15/16
74-11/16
76-7/16
78-3/16
79-15/16
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
AX-SX &
SSAX
ONLY
AXS
SAX
AXS-XX-26
ONLY
NOTE: The millwork must be constructed in such a manner as to provide a weight capacity greater than
the total assembled weight.
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.
MILLWORK SPECIFICATIONS

Hex Head
Screws (2)
10-32 x 1/4”
Page 7
ROUGH-IN PAN ASSEMBLY
1) Install both cable carriers to rear flange of rough-in pan using (2) 10-32 x 1/4 hex head screws per
cable carrier. (FIGURE A)
NOTE: Installation hardware is provided with cable carrier kit.
FIGURE A
WARNING! Cable Carriers are an integral part of this system and must be installed for the safe
operation of this product to prevent the system from tipping and sliding off of tracks. Failure to install
cable carriers can result in serious damage to equipment and/or risk of injury .
Rear Flange
Cable
Carriers
Rough-In Pan
2) Fold up both cable carriers and tie back with rubber bands or twine for ease of installation.
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.

ROUGH-IN PAN ASSEMBLY (CONTINUED)
Page 8
2) Position rough-in pan assembly into millwork mounting platform and mount with appropriate
customer-supplied hardware. (FIGURE B)
NOTE: Refer to MILLWORK SPECS on page 5 for specific front setback dimensions.
Mounting
Locations
Mounting
Locations
FIGURE B
Rough-In
Pan Assembly
Millwork
Mounting
Platform

RACK ASSEMBLY
Page 9
1) Align the (4) pre-installed mounting studs on each rackrail with mounting holes in top and bottom
frames. (FIGURE C)
2) Loosely secure each rackrail to top and bottom frame using (2) 5/16 flange nuts per frame.
(FIGURE C)
Mounting Studs
(4 Per Rackrail)
5/16 Flange Nuts
(4 Per Rackrail)
Rackrail
Top Frame
Bottom Frame
FIGURE C
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.

RACK ASSEMBLY (Continued)
3) Install (4) 10-32 Hex Head screws through top and bottom frames into each rackrail. (FIGURE D)
4) Install (2) squaring panels on front and rear of assembly using (4) 10-32 x 1/4” screws. Locate
squaring panels at the mid-point of rackrail assembly. (FIGURE D)
FIGURE D
Squaring
Panels
(2)
Hex Head
Screws 10-32
(4 Per Rackrail)
Screws 10-32
(4 Per
Squaring
Panel)
Top Frame
Bottom Frame
Rackrail
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.
Page 10

EQUIPMENT LOADING AND SQUARING PANELS
To eliminate the possibility of a center bow in the
frame, Middle Atlantic Products suggests that the
squaring panels be left in place until some of your
components have been mounted.
RACK ASSEMBLY (Continued)
Page 11
5) Install (2) support brackets on pre-installed rackrail mounting studs using (4) 10-32 hex head
screws. (FIGURE E)
NOTE: Support brackets only included with larger racks.
Nuts 10-32
(2 Per
Squaring
Panel)
Support Brackets (2)
(Included with
larger racks)
Top Trim Panel
Phillips Head
Screws (2) 10 -32 x 1/4”
6) Lay assembly on a flat, level surface and square frame on all
four corners. (FIGURE F)
FIGURE F
(CORRECT) (INCORRECT)
RACK RACK
7) Tighten all flange nuts.
8) Install top trim panel using (2) 10-32 x 1/4” screws.
(FIGURE G)
NOTE: Top trim panel contains only two screw holes.
1) Construct rough opening and base.
2) Assemble frame.
3) Install cable carriers / rough-in pan.
4) Install service stand.
5) Attach frame to tracks and cable
carriers.
6) Assemble leash.
7) Tie cable to carriers.
8) Secure rack in millwork.
FIGURE E
FIGURE G

Hex Head
Screws
(2 Per Track)
10-32
Slide Support Screws
(2 Per Track)
SERVICE STAND / SERVICE TRACK ASSEMBLY
Page 12
1) Assemble service stand as per instructions
included with unit.
2) Adjust stand to approximate height of
rough-in pan. (FIGURE H)
3) Position notched end of each service track on
service stand saddles. (FIGURE H)
CAUTION! Be sure notched ends are
fully seated in service stand saddles
to prevent tracks from falling out.
4) Position opposite end of each service
track on millwork. (FIGURE H)
5) Secure each service track to rough-in
pan using (2) 10-32 hex head
screws (included in service
track hardware kit). (FIGURE I)
Notches
Saddle
Service
Stand
Service
Tracks
Saddle Rough-in
Pan
FIGURE H
6) Fine adjust the service stand with
the aid of the level installed in the
service tracks.
7) Extend slide supports on each service
track to meet millwork using slide
support screws (2 per service track).
(FIGURE J)
NOTE: This adjustment strengthens track when extending heavy equipment for servicing.
FIGURE I
FIGURE J
Slide
Support
!

1) Place rack on service track assembly (observe proper front/rear
orientation). (FIGURE K)
Installer provides anchor
hardware to top of cabinet millwork
NOTE: The leash can be shortened by tying knots in it.
4) Extend frame until cable carriers stop frame at full out position.
5) Attach opposite end of leash to a stable point in your cabinet / millwork with hardware of your choice.
Phillips Head Screw
(1) 10-32 x 5/8”
CAUTION! Do not allow the frame to roll off end of tracks.
RACK AND CABLE CARRIER INSTALLATION
Page 13
2) Extend and secure each cable carrier to frame using (2) 10-32 hex
head screws (included in service track hardware kit). (FIGURE K)
3) Install one end of the leash to top rear of frame using
(1) 10-32 x 5/8” Phillips head screw (included leash hardware kit).
(FIGURE L)
Hex Head Screws
(2 Per Cable Carrier) 10-32
Rack
Cable Carriers
FIGURE K
CAUTION! The leash is an integral part of this system and must
be installed to prevent system from tipping and sliding off tracks.
FIGURE L
Leash

1) Extend cable carriers fully. (FIGURE K)
2) Route cables through cable carrier channel. (FIGURE M)
3) Tie cabling in a bundle and secure to center
of cable carrier channel. (FIGURE M)
4) Leave service loop at hinge point to allow for folding.
NOTE: Observe and adjust for pinch points.
CABLE CARRIER
TIE CABLES
AS SHOWN
DID YOU KNOW?
Optional part #
AXS-WT25/WT50
is available to
handle larger
cable bundles
PART # FITS
AXS-WT-25 AX-SX, SSAX
AXS-WT50 AXS, SAX
NOTE: If the loaded rack frame springs outward during installation,
it can be secured directly to the millwork wherever a blank panel is
located. With rack closed, remove blank panel and install
customer-supplied screws through each side of front rackrail
into millwork. (FIGURE O)
FIGURE M
1) Roll loaded rack into millwork.
2) Install bottom trim panel using (4) 10-32 Phillips head screws
(included in hardware kit). (FIGURE N)
3) Remove tracks and service stand. Phillips Head
Screws (4)
10 -32 x 1/4”
CABLE MANAGEMENT
Page 14
SECURING RACK ASSEMBLY IN MILLWORK
WARNING! The trim panel is integral to the safe operation
of this product and is required to prevent the rack
from sliding out. Failure to install trim panel can result in
serious damage to equipment and/or risk of injury.
Bottom
Trim Panel
FIGURE N
FIGURE O

Page 15
1) Remove dust and debris from rack surface with included wipes. (FIGURE P)
2) Remove paper backing from gasket and adhere gasket to bottom of rackrail. (FIGURE P)
3) Gently pull gasket up to top of rack while removing paper
backing. Press firmly along length of gasket. (FIGURE P)
4) Align gasket at top of rackrail and continue adhering
across top and down to opposite side of rack.
5) Trim excess length.
CLEAN
ALONG
THESE
SURFACES
GASKET
ALIGN GASKET TO EDGE
OF FLAT SURFACE
1) Remove dust and debris from
rack surface with included wipes.
(FIGURE Q)
2) Remove paper backing from
adhesive and press firmly to
adhere guide. (FIGURE Q)
CLEAN ALONG
THESE SURFACES
HOLE IN GUIDE
INDICATES BACK
ALIGN TOP OF
GUIDE AGAINST
TOP OF RACKRAIL
FIGURE P
FIGURE Q
GASKET KIT (OPTIONAL) INSTALLATION
GUIDE KIT (OPTIONAL) INSTALLATION

Page 16
WARRANTY
Middle Atlantic Products (the "Company") warrants the Equipment Access System to be free from
defects in material or workmanship under normal use and conditions for a period of (3) years from the
date of shipment by the company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of
and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products
purchased, or any part or parts thereof, which the Company has determined to be defective after
inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [email protected]
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.