Middle Atlantic WoodKit C3 Series User manual

THANK YOU
Thank you for purchasing a C3 Series Display Mount Large Cover option. Please read these
instructions thoroughly before installing or assembling this product.
C3 Series
Display Mount Large Cover Option (C3-XX-XCVR-BK)
Instruction Sheet
100-00035 Rev A
NOTE: Single and dual large cover options shown.

IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, understand and follow the following information can result in serious personal injury, damage to the
equipment or voiding of the warranty. It is the responsibility of the Installer/User to ensure that this product is loaded according to
specifications.
WARNING: Middle Atlantic Products, electrical systems conform to and should be properly grounded in compliance with require-
ments of the current National Electrical Code or codes administered by local authorities. All electrical products may present a possible
shock or fire hazard if improperly installed or used. Electrical products may bear the mark of a Nationally Recognized Testing
Laboratory (NRTL) and should be installed in conformance with current local and/or the National Electrical Code.
WARNING: A warning alerts you to a situation that could result in serious personal injury or death.
AVERTISSEMENT: Un avertissement vous avertit d'une situation pouvant entraîner des blessures graves ou la mort.
INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ
AVERTISSEMENT:Refus de lire, comprendre et suivre la renseignements suivants peut traduire par de graves blessures, des
dommages à l'équipement ou invalider la garantie. Il est la responsabilité de l'installateur / utilisateur de s'assurer que ce produit
est chargé conformément aux spécifications.
AVERTISSEMENT: Les produits Middle Atlantic, les systèmes électriques sont conformes et doivent être correctement mis à la
terre conformément aux exigences du Code national de l'électricité en vigueur ou aux codes administrés par les autorités locales.
Tous les produits électriques peuvent présenter un risque d'électrocution ou d'incendie s'ils sont mal installés ou utilisés. Les
produits électriques peuvent porter la marque d'un laboratoire d'essais reconnu au niveau national (NRTL) et doivent être installés
conformément au code électrique local et/ou national en vigueur.
• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Clean only with dry cloth.
• Only use attachments/accessories specified by the manufacturer.
• Lire ces instructions.
• Conservez ces instructions.
• Respectez tous les avertissements.
• Suivez toutes les instructions.
• Nettoyer uniquement avec un chiffon sec.
• N'utilisez que des accessoires spécifiés par le fabricant.
DANGER HAZARDOUS VOLTAGE: The lightning flash with the arrowhead symbol, within an equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
DANGER TENSION DANGEREUSE: Le symbole de la pointe de flèche, dans un triangle équilatéral, est destiné à alerter l'utilisateur sur la
présence de tension dangereuse non isolée dans l'enceinte du produit qui peut être d'une ampleur suffisante pour constituer un risque d'électrocu-
tion.
SUPPLIED COMPONENTS AND HARDWARE
(3x)
10-32 x ½”
Thread
Cutting
Screw
X
Large Cover
NOTE: Single and Dual models shown.
A
C3-32-SCVR-BK
C3-24-SCVR-BK
C3-32-DCVR-BK
C3-24-DCVR-BK
Model No. Width
Single, 21” (533 mm)
Single, 21” (533 mm)
Dual, 44” (1118 mm)
Dual, 44” (1118 mm)
Height
24” (610 mm)
32” (813 mm)
24” (610 mm)
32” (813 mm)
NOTE:
• To order more hardware, contact support
at 1-800-266-7225.
• Additional hardware is included that may
not be required for your installation.
Page 2

REQUIRED TOOLS
• Power Driver
• #2 Phillips Bit
• #2 Phillips Screwdriver
WARNING: Use tools with caution and follow all
necessary safety protocols.
AVERTISSEMENT: Utiliser des outils avec prudence
et suivre tous les protocoles de sécurité nécessaires.
INTRODUCTION
NOTE: Only use this instruction sheet to install your C3 Series display mount large cover option after
completing the following:
1. Refer to the C3 Series Credenza Frame instruction sheet (100-00032) and secure the frame to your
wall.
2. Refer to the following instruction sheets to install the C3 Series options you may have purchased for
your credenza.
○ C3 Series Display Mount Option (C3-XX-LDXU) Instruction Sheet (100-00034)
○ C3 Series Slide-Out Rack Option (C3-TECHKIT4-SO) Instruction Sheet (100-00036)
○ C3 Series Fixed Rack Option (C3-TECHKIT4-ST) Instruction Sheet (100-00037)
○ C3 Series Shelf Option (C3-SHELFKIT) Instruction Sheet (100-00038)
3. Refer to the C3 Series WoodKit instruction sheet (100-00040) to install your woodkit.
NOTE:
• Kits and options other than the fan kit and large cover option should be installed before your woodkit
is attached to the frame.
• Instruction sheets may also be accessed at www.middleatlantic.com.
Page 3
1. Place the lower edge of your display
mount large cover option (X) into the
opening on the top of your credenza.
The edge should sit on top of the horizontal
cover on your frame and against the display
mount uprights as shown. (FIGURE A)
2. Bring the top edge of the display mount large
cover option flat against the uprights.
INSTALLATION
A
NOTE: Dual large cover option shown in black for clarity. The
procedure is the same for a single large cover option on C3
credenzas with any number of bays.
FIGURE A
Place lower edge of
large display cover
option into the credenza
top opening on the
back of the woodkit and
against the uprights first,
and then bring the top
edge even.

WARRANTY
For warranty information, refer to http://www.middleatlantic.com/company/about-us.aspx#warranty
Corporate Headquarters
Voice: 973-839-1011 - Fax: [phone] - International Voice: [phone] -
Fax: [phone] - www.middleatlantic.com - [email protected]
Middle Atlantic Canada
Voice: 613-836-2501 - Fax: [phone] - ca.middleatlantic.com -
[email protected]
Middle Atlantic EMEA Technical Support
Voice: [phone] - [email protected]
Factory Distribution
United States: New Jersey, California, Illinois - Canada: Ontario - The Netherlands: Weert
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
Page 4
NOTE: Verify the torque on your power driver is on the lightest
setting and only increase as necessary.
3. Use a power driver, #2 Phillips bit and (2x) 10-32 x ½” thread
cutting screws (B) through the holes in the top corners of
the display mount large cover option and into the holes on
the uprights. (FIGURE B)
INSTALLATION (CONTINUED)
B
FIGURE B