Miele G 1 Series User manual

PROGRAMMING MODE
G 1xxx and G 2xxx Dishwashers
(All US Models)
© 2010 Miele USA

Technical Information
2
G 1xxx/G 2xxx
Table of Contents
1Customer Programming...........................................................................................3
2Service Programming...............................................................................................4
2.1Inspira and Advanta - G 118x/G 2170/G 218x............................................................4
2.2Optima - G 1202.........................................................................................................8
2.3Optima - G 1262.......................................................................................................12
2.4Optima - G 1470/G 2470...........................................................................................16
2.5Optima - G 1472/G 2472...........................................................................................20
2.6Advanta - G 2020......................................................................................................23
2.7Inspira and Diamante - G 2120/G 2140/G 2150 .......................................................26
2.8Inspira and Diamante - G 2142/G 2143....................................................................29
2.9Optima - G 2420/G 243x...........................................................................................32
2.10Excella - G 2630/G 2670...........................................................................................36
2.11Excella - G 2732 .......................................................................................................39
2.12 LaPerla - G 283x/G 2872..........................................................................................42
2.13Activating Dealer Demo Mode (Excella/LaPerla)......................................................46
2.14Activating/Deactivating the Sensor Softener; Manually Setting Water Hardness
(Excella/LaPerla) ......................................................................................................46
List of Tables
Table 1: Customer Programming Summary.................................................................................... 4
Table 2: Service Programming Mode Summary, G 118x/G 2170/G 218x...................................... 7
Table 3: Water Hardness Settings, G 118x/G 2170/G 218x........................................................... 7
Table 4: Rinse Aid Quantities, G 118x/G 2170/G 218x................................................................... 8
Table 5: Service Programming Mode, G 1202.............................................................................. 11
Table 6: Water Hardness Settings, G 1202................................................................................... 12
Table 7: Rinse Aid Settings, G 1202 ............................................................................................. 12
Table 8: Service Programming Mode, G 1262.............................................................................. 15
Table 9: Water Hardness Settings, G 1262................................................................................... 16
Table 10: Rinse Aid Settings, G 1262 ........................................................................................... 16
Table 11: Service Programming Mode, G 1470/G 2470............................................................... 19
Table 12: Water Hardness Settings, G 1470/G 2470.................................................................... 20
Table 13: Service Programming Mode, G 1472/G 2472............................................................... 23
Table 14: Water Hardness Settings, G 1472/G 2472.................................................................... 23
Table 15: Service Programming Mode Summary, G 2020 ........................................................... 25
Table 16: Water Hardness Settings, G 2020................................................................................. 26
Table 17: Rinse Aid Quantities, G 2020........................................................................................ 26
Table 18: Service Programming Mode Summary, G 2120/G 2140/G 2150.................................. 28
Table 19: Water Hardness Settings, G 2120/G 2140/G 2150....................................................... 28
Table 20: Rinse Aid Quantities, G 2120/G 2140/G 2150.............................................................. 29
Table 21: Service Programming Mode Summary, G 2142/G 2143............................................... 31
Table 22: Water Hardness Settings, G 2142/G 2143.................................................................... 31
Table 23: Rinse Aid Quantities, G 2142/G 2143........................................................................... 32
Table 24: Service Programming Mode, G 2420/G 243x............................................................... 35
Table 25: Water Hardness Settings, G 2420/G 243x.................................................................... 36
Table 26: Service Programming Mode, G 2630/G 2670............................................................... 39
Table 27: Service Programming Mode, G 2732............................................................................ 42
Table 28: Service Programming Mode, G 283x/G 2872 ............................................................... 45

Technical Information
3
G 1xxx/G 2xxx
1 Customer Programming
The customer programming mode includes certain parts of the service
programming mode. All programming options can be carried out in service
programming mode (see Section 2).
Close the appliance door and switch off the power before accessing customer
programming mode.
To save settings, switch off the appliance after making changes.
Note:
Customer programming mode is not available on Excella or LaPerla
machines; instead, these machines feature a Settings menu. Refer to the
appropriate operating instructions.
Model Access Procedure Available Options
G 118x/G 2170/G 218x
(See Section 2.1 for option
descriptions.)
1. Press and hold Program button.
2. Switch on appliance and wait
approx. 4 sec. for “Rinse & Hold”
LED to light up.
3. Release Program button.
Water hardness
Rinse aid
Buzzer on/off
Reset standard settings
G 1202
(See Section 2.2 for option
descriptions.)
1. Press and hold Program and
Start/Stop buttons.
2. Switch on appliance and wait
approx. 4 sec. for "Start/Stop" LED
to light up.
3. Release Program and Start/Stop
buttons.
Water hardness
Rinse aid
Adjust Sensor Wash
Reset standard settings
G 1262
(See Section 2.3 for option
descriptions.)
1. Press and hold Program button.
2. Switch on appliance and wait
approx. 4 sec. for “Rinse & Hold”
LED to light up.
3. Release Program button.
Rinse aid
Buzzer on/off
Reset standard settings
G 147x/G 247x
(See Sections 2.4 and 2.5 for
option descriptions.)
1. Press and hold Program button.
2. Switch on appliance and wait
approx. 4 sec. for "Rinse & Hold"
LED to light up.
3. Release Program button.
Check and set water
hardness (up to ID -1080);
activate/ deactivate
softener sensor, set water
hardness (after ID -1080)
Rinse aid
Buzzer on/off
Adjust Sensor Wash
program (after ID -984)
Check water hardness
(after ID -1080)
Reset standard settings
G 2020
(See Section 2.6 for option
descriptions.)
1. Turn the control dial to the 12
o’clock position.
2. Press and hold Start/Stop button.
3. Switch on appliance and wait
approx. 4 sec. for "Start/Stop" LED
to light up.
4. Release Start/Stop button.
Water hardness (3 o’clock)
Rinse aid (5 o’clock)
Resetting standard
settings (11 o’clock)

Technical Information
4
G 1xxx/G 2xxx
Model Access Procedure Available Options
G 2142/G 2143/G 2120/
G 2140/G 2150
(See Sections 2.7 and 2.8 for
option descriptions.)
1. Press and hold Start/Stop button.
2. Switch on appliance and wait
approx. 4 sec. for "Start/Stop" LED
to light up.
3. Release Start/Stop button.
Water hardness
Rinse aid
Reset standard settings
G 2420/G 243x
(See Section 2.9 for option
descriptions.)
1. Press and hold Start/Stop button.
2. Switch on appliance and wait
approx. 4 sec. for "Start/Stop" LED
to light up.
3. Release Start/Stop button.
Check and set water
hardness (up to ID -1080);
activate/ deactivate
softener sensor, set water
hardness (after ID -1080)
Rinse aid
Adjust Sensor Wash
program (after ID -984)
Check water hardness
(after ID -1080)
Reset standard settings
Table 1: Customer Programming Summary
2 Service Programming
2.1 Inspira and Advanta - G 118x/G 2170/G 218x
Initial requirements:
1. Open the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Program button.
2. Switch on the appliance.
3. Release the Program button.
4. Immediately press the Program button 5 times; on the 5th time, hold until
the "Rinse & Hold" LED flashes (5 flashes per second).
5. Release the Program button.
6. If the "Rinse & Hold" LED does not light up, repeat the procedure.

Technical Information
5
G 1xxx/G 2xxx
Options:
Function Programming Display
Reset
Press the Program button
1x. To reset all parameters
to standard settings, press
and hold the Program
button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 1x
rapidly. "SaniWash" LED is off:
values do not correspond to
standard settings; "SaniWash" LED
flashes: values correspond to
standard settings.
Water hardness setting
Briefly press Program 2x.
To set the desired water
hardness, press and hold
the Program button until
the "Intake/Drain" LED
lights up. Then select the
desired value by briefly
pressing the Program
button as appropriate.
The "Intake/Drain" LED flashes 2x
rapidly at intervals. The set value is
indicated by the "SaniWash" LED
flash pattern. If the "SaniWash" LED
flashes 4x rapidly at intervals, this
corresponds to the standard setting
of 12 - 15°d (12.8 - 16.1 gpg); see
Table 3.2
Dispensed rinse aid
quantity setting
Briefly press Program 3x.
To set the desired
quantity, press and hold
the Program button until
the "Intake/Drain" LED
lights up. Then select the
desired value by briefly
pressing the Program
button as appropriate.
The "Intake/Drain" LED flashes 3x
rapidly at intervals. The set value is
indicated by the "SaniWash" LED
flash pattern. If this LED flashes 3x
rapidly at intervals, this corresponds
to the standard setting of 0.1 fl.oz.
(3mL). Range: 0 - 0.2 fl.oz. (0 - 6
mL); see Table 4.
Buzzer on/off
Briefly press the Program
button 4x. To make the
desired setting, press and
hold the Program button
until the "Intake/Drain"
LED lights up. Then select
the desired setting by
briefly pressing the
Program button as
appropriate.
The "Intake/Drain" LED flashes 4x
rapidly at intervals. "SaniWash"
LED is off: Buzzer on (standard
setting). "SaniWash" LED flashes:
Buzzer off.
Resetting standard
settings
Briefly press Program
12x. To reset all
parameters to standard
settings, press and hold
the Program button until
the "Intake/Drain" LED
lights up. Then briefly
press the Program button.
The "Intake/Drain" LED flashes 1x
slowly and 2x rapidly at intervals.
This programmable function can be
used to reset all parameters that can
be modified by the customer to
standard settings. If the "SaniWash"
LED is off, the values do not
correspond to standard settings. If
the "SaniWash" LED flashes, the
values correspond to standard
settings.

Technical Information
6
G 1xxx/G 2xxx
Function Programming Display
Adjusting the main wash
temperature
Press the Program button
20x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 2x
slowly. "SaniWash" LED is off:
standard setting; "SaniWash" LED
flashes: increased wash
temperature. Increased wash
temperature results in longer
running time.
Shortening program
sequence
Press the Program button
22x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 2x
slowly and 2x rapidly. "SaniWash"
LED is off: Standard setting;
"SaniWash" LED flashes:
Shortened wash program. Program-
dependent shortening of running
time by reduction of temperature
and/or removing holding times.
Water quantity
normal/increased
Press the Program button
23x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 2x
slowly and 3x rapidly. "SaniWash"
LED is off: Standard setting;
"SaniWash" LED flashes: Increased
water quantity. If “Increased water
quantity” is selected, water intake
increases by approx. 16.7 fl.oz.
(500mL).
Second interim rinse
Press the Program button
26x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 2x
slowly and 6x rapidly. "SaniWash"
LED is off: Standard setting;
"SaniWash" LED flashes: With
second interim rinse.
Activating/deactivating
improved drying
Press the Program button
27x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes
2x slowly and 7x rapidly.
"SaniWash" LED is off: Standard
setting; "SaniWash" LED flashes:
Improved drying – depending on the
program, drying time is extended
and the final rinse temperature
increased.
Appliance width setting1
Press the Program button
35x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 3x
slowly and 5x rapidly. "SaniWash"
LED is off: Appliance width 24”
(60cm) (standard setting);
"SaniWash" LED flashes: Appliance
width 18” (45cm).
Appliance height setting1
Press the Program button
36x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 3x
slowly and 6x rapidly. "SaniWash"
LED is off: Standard appliance
height (G 1xxx); "SaniWash" LED
flashes: XXL models (G 2xxx).

Technical Information
7
G 1xxx/G 2xxx
Function Programming Display
Model setting1
Press the Program button
38x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 3x
slowly and 8x rapidly. "SaniWash"
LED off: Models without drying fan;
"SaniWash" LED flashes: Models
with UTT version 1 or 2.3
Country setting1
Press the Program button
39x. To make the desired
setting, press and hold the
Program button until the
"Intake/Drain" LED lights
up. Then briefly press the
Program button.
The "Intake/Drain" LED flashes 3x
slowly and 9x rapidly. The
"SaniWash" LED’s flash pattern
indicates which country is set: 1x:
Europe; 2x: Australia; 3x: USA; 4x:
Japan; 5x: Italy/Spain; 6x: Southern
Europe.4
Table 2: Service Programming Mode Summary, G 118x/G 2170/G 218x
1 If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
2If the dishwasher is connected to an external ion exchanger water softener (i.e. that
needs to be regenerated with salt), the water hardness delivered by the system must be
set. If this value is unknown, set to 8°d (8.6 grains per gallon).
3Circulation Turbothermic drying (UTT) version 1 (w/condenser), version 2 (w/out condenser).
4The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.
Water Hardness [°d] Water Hardness [gpg] Flash Pattern of
"SaniWash" LED
1 – 4 1.1 – 4.3 1x rapidly
5 – 7 5.4 – 7.5 2x rapidly
8 – 11 8.6 – 11.8 3x rapidly
12 – 15 12.8 – 16.1 4x rapidly1
16 – 20 17.1 – 21.4 5x rapidly
21 – 25 22.5 – 26.8 6x rapidly
26 – 30 27.8 – 32.1 7x rapidly
31 – 36 33.2 – 38.5 8x rapidly
37 – 50 39.6 – 53.5 9x rapidly
51 – 70 54.6 – 74.9 1x slowly
Table 3: Water Hardness Settings, G 118x/G 2170/G 218x
1Standard setting.

Technical Information
8
G 1xxx/G 2xxx
Rinse Aid Volume [mL]1Flash Pattern of "SaniWash" LED
0 —
1 1x rapidly
2 2x rapidly
3 3x rapidly2
4 4x rapidly
5 5x rapidly
6 6x rapidly
Table 4: Rinse Aid Quantities, G 118x/G 2170/G 218x
1One milliliter equals 0.3 fluid ounces.
2Standard setting.
2.2 Optima - G 1202
Initial requirements:
1. Close the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Start/Stop button.
2. Switch on the appliance.
3. Release the Start/Stop button.
4. Immediately press the Start/Stop button 5 times; on the 5th time, hold
until the "Start/Stop" LED flashes (5 flashes per second).
5. Release the Start/Stop button.
6. If the "Start/Stop" LED does not light up, repeat the procedure.
Options:
Function Programming Display
Software version ID check Do not press the Delay
Start button. The "Delay
Start" LED is not lit.
"Rinse" LED is out or flashes. The
display shows the software version
ID no. in consecutive digits
(e.g., -1304).
Reset
Press the Delay Start
button 1x. The "Delay
Start" LED flashes 1x
rapidly intermittently.
Press the Start/Stop
button to reset all standard
settings.
The "Rinse" LED is out or flashes.
This programmable function can be
used to reset all modifiable
parameters to their standard
settings. The display shows pand a
digit alternately: p0 = Non-standard
settings have been made; p1 = All
settings reset to standard settings
or no modifications have been
made.

Technical Information
9
G 1xxx/G 2xxx
Function Programming Display
Water hardness setting1
Press the Delay Start
button 2x. The "Delay
Start" LED flashes 2x
rapidly intermittently.
Press the Start/Stop
button as appropriate to
set the desired water
hardness.
The "Rinse" LED is out or flashes.
The display shows pand the digit/s
of the set value alternately.
Setting range: p1 to p70; see Table
6.2
Dispensed rinse aid
quantity setting
Press the Delay Start
button 3x. The "Delay
Start" LED flashes 3x
rapidly intermittently.
Press the Start/Stop
button as appropriate to
make the desired setting.
The "Rinse" LED is out or flashes.
The display shows P and a digit
alternately: e.g., P3 (standard
setting) indicates a dispensed
quantity of 0.1 fl.oz. (3mL). Setting
range: 0 - 0.2 fl.oz. (0 - 6 mL). See
Table 7.
Adjust Sensor Wash
program
Press Delay Start 5x. The
"Delay Start" LED flashes
5x rapidly intermittently.
Press the Start/Stop
button to change the
setting.
The "Rinse" LED is out or flashes.
The display shows Pand a digit
alternately. Setting options: P0 =
Standard program cycle (factory
setting); P1 = Adjusted program
cycle. The Sensor Wash program
can be adjusted in this parameter to
deal with stubborn soiling (or
otherwise low overall soiling). If this
option is selected, the main wash
temperature is increased to 131°F
and, as a result, the program
duration is extended.
Resetting standard
settings
Press Delay Start 12x.
The "Delay Start" LED
flashes 1x slowly and 2x
rapidly intermittently.
Press the Start/Stop
button to reset all settings
back to their factory
values.
The "Rinse" LED is out or flashes.
This programmable function can be
used to reset all customer-modified
parameters back to their standard
settings. The display shows Pand a
digit alternately. P0 = Settings have
been modified; P1 = All settings reset
to standard settings or no
modifications have been made.
Adjusting the main wash
temperature
Press the Delay Start
button 20x. The "Delay
Start" LED flashes 2x
slowly. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is out or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = Wash
temperature increased. If this option
is selected, the main wash
temperature is increased and, as a
result, the program duration is
extended.

Technical Information
10
G 1xxx/G 2xxx
Function Programming Display
Water quantity
normal/increased
Press the Delay Start
button 23x. The "Delay
Start" LED flashes 2x
slowly and 3x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately: p0 = Normal water
quantity (standard setting); p1 =
Increased water quantity. If
increased water quantity is
selected, approx. 16.7 fl.oz.
(500mL) more water is taken in
during each water intake cycle.
Soak activation/
deactivation
Press the Delay Start
button 24x. The "Delay
Start" LED flashes 2x
slowly and 4x rapidly
intermittently.
Press the Start/Stop
button as appropriate to
make the desired setting.
The "Rinse" LED is off or flashes.
The display shows p and a digit
alternately. Setting options: p0 =
Soak not activated; p1 = Soak
activated. If powder detergent is
used, approximately 1 teaspoon (5
grams) should be poured into
detergent chamber 1.
Pre-wash activation/
deactivation
Press the Delay Start
button 25x. The "Delay
Start" LED flashes 2x
slowly and 5x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
Pre-wash not activated; p1 =
Pre-wash activated.
Second interim rinse
Press the Delay Start
button 26x. The "Delay
Start" LED flashes 2x
slowly and 6x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = With second
interim rinse.
Activating/deactivating
improved drying
Press the Delay Start
button 27x. The "Delay
Start" LED flashes 2x
slowly and 7x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
Normal drying time; p1 = Extended
drying time.
Appliance width setting1
Press the Delay Start
button 35x. The "Delay
Start" LED flashes 3x
slowly and 5x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
24” (60cm); p1 = 18” (45cm).

Technical Information
11
G 1xxx/G 2xxx
Function Programming Display
Appliance height setting1
Press the Delay Start
button 36x. The "Delay
Start" LED flashes 3x
slowly and 6x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options:
p0 = Normal machine height (G
1xxx); p1 = XXL model (G 2xxx).
Model setting1
Press the Delay Start
button 38x. The "Delay
Start" LED flashes 3x
slowly and 8x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows p and a digit
alternately. Individual setting
possibilities depend on model and
whether a circulation pump with
slide shutter (WAW), sensor
softener (SEH), and/or salt
container in door (SIT) are fitted.
Appropriate setting: p1 = G 1202
(w/out WAW, w/out SEH, w/out
SIT).
Country setting1
Press the Delay Start
button 39x. The "Delay
Start" LED flashes 3x
slowly and 9x rapidly
intermittently. Press the
Start/Stop button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. The following country
versions can be set: p1 = EUR
(Europe); p2 = AUS (Australia);
p3 = USA, p4 = JPN (Japan),
p5 = I/E (Italy/Spain), p6 = SER
(Southern Europe).3
Table 5: Service Programming Mode, G 1202
1 If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
2If the dishwasher is connected to an external ion exchanger water softener (i.e. that
needs to be regenerated with salt), the water hardness delivered by the system must be
set. If this value is unknown, set to 8°d (8.6 grains per gallon).
3The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.

Technical Information
12
G 1xxx/G 2xxx
Water Hardness [°d] Water Hardness [gpg] Display
1 1.1
P1
2 2.1
P2
3 3.2
P3
… … …
36 38.5
P36
37 – 50 39.6 – 53.5 P50
51 – 60 54.6 – 64.2 P60
61 – 70 65.3 – 74.9 P70
Table 6: Water Hardness Settings, G 1202
Rinse Aid Volume [mL]1Display
0 P0
1 P1
2 P2
3 P32
4 P4
5 P5
6 P6
Table 7: Rinse Aid Settings, G 1202
1One milliliter equals 0.3 fluid ounces.
2Standard setting.
2.3 Optima - G 1262
Initial requirements:
1. Open the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Program button.
2. Switch on the appliance.
3. Release the Program button.
4. Immediately press the Program button 5 times; on the 5th time, hold until
the "Rinse & Hold" LED flashes (5 flashes per second).
5. Release the Program button.
6. If the "Rinse & Hold" LED does not light up, repeat the procedure.

Technical Information
13
G 1xxx/G 2xxx
Options:
Function Programming Display
Software version ID check Do not press the Tab
button. The "Tab" LED is
not lit.
The display shows the software
version ID no. in consecutive digits
(e.g., -1304).
Reset
Press the Tab button 1x.
The "Tab" LED flashes 1x
rapidly intermittently.
Press the Program button
to reset all standard
settings.
This programmable function can be
used to reset all modifiable
parameters to their standard
settings. The display shows pand a
digit alternately: p0 = Non-standard
settings have been made; p1 = All
settings reset to standard settings
or no modifications have been
made.
Water hardness setting1
Press the Tab button 2x.
The "Tab" LED flashes 2x
rapidly intermittently.
Press the Program button
as appropriate to set the
desired water hardness.
The display shows pand the digit/s
of the set value alternately.
Setting range: p1 to p70; see Table
9.2
Dispensed rinse aid
quantity setting
Press the Tab button 3x.
The "Tab" LED flashes 3x
rapidly intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows P and a digit
alternately: e.g., P3 (standard
setting) indicates a dispensed
quantity of 0.1 fl.oz. (3mL). Setting
range: 0 - 0.2 fl.oz. (0 - 6 mL). See
Table 10.
Buzzer on/off
Press the Tab button 4x.
The "Tab" LED flashes 4x
rapidly intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows pand a digit
alternately: p0 = Buzzer off; p1 =
Buzzer on.
Adjust Sensor Wash
program
Press Tab 5x. The "Tab"
LED flashes 5x rapidly
intermittently. Press the
Program button to change
the setting.
The display shows Pand a digit
alternately. Setting options: P0 =
Standard program cycle (factory
setting); P1 = Adjusted program
cycle. The Sensor Wash program
can be adjusted in this parameter to
deal with stubborn soiling (or
otherwise low overall soiling). If this
option is selected, the main wash
temperature is increased to 131°F
and, as a result, the program
duration is extended.
Resetting standard
settings
Press Tab 12x. The "Tab"
LED flashes 1x slowly and
2x rapidly intermittently.
Press the Program button
to reset all settings back to
their factory values.
This programmable function can be
used to reset all customer-modified
parameters back to their standard
settings. The display shows Pand a
digit alternately. P0 = Settings have
been modified; P1 = All settings reset
to standard settings or no
modifications have been made.

Technical Information
14
G 1xxx/G 2xxx
Function Programming Display
Adjusting the main wash
temperature
Press the Tab button 20x.
The "Tab" LED flashes 2x
slowly. Press the Program
button as appropriate to
make the desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = Wash
temperature increased. If this option
is selected, the main wash
temperature is increased and, as a
result, the program duration is
extended.
Water quantity
normal/increased
Press the Tab button 23x.
The "Tab" LED flashes 2x
slowly and 3x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately: p0 = Normal water
quantity (standard setting); p1 =
Increased water quantity. If
increased water quantity is
selected, approx. 16.7 fl.oz.
(500mL) more water is taken in
during each water intake cycle.
Soak activation/
deactivation
Press the Tab button 24x.
The "Tab" LED flashes 2x
slowly and 4x rapidly
intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows p and a digit
alternately. Setting options: p0 =
Soak not activated; p1 = Soak
activated.
Pre-wash activation /
deactivation
Press the Tab button 25x.
The "Tab" LED flashes 2x
slowly and 5x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. Setting options: p0 =
Pre-wash not activated; p1 =
Pre-wash activated.
Second interim rinse
Press the Tab button 26x.
The "Tab" LED flashes 2x
slowly and 6x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = With second
interim rinse.
Activating/deactivating
improved drying
Press the Tab button 27x.
The "Tab" LED flashes 2x
slowly and 7x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Normal drying time; p1 = Extended
drying time.
SC (with or without cutlery
tray) - available for ID no.
-1856
Press the Tab button 28x.
The "Tab" LED flashes 2x
slowly and 8x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting
The display shows pand a digit
alternately.
Programming function not available
at this time.

Technical Information
15
G 1xxx/G 2xxx
Function Programming Display
Appliance width setting1
Press the Tab button 35x.
The "Tab" LED flashes 3x
slowly and 5x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
24” (60cm); p1 = 18” (45cm).
Appliance height setting1
Press the Tab button 36x.
The "Tab" LED flashes 3x
slowly and 6x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options:
p0 = Normal machine height (G
1xxx); p1 = XXL model (G 2xxx).
Model setting1
Press the Tab button 38x.
The "Tab" LED flashes 3x
slowly and 8x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows p and a digit
alternately. Individual setting
possibilities depend on model and
whether a circulation pump with
slide shutter (WAW), sensor
softener (SEH), and/or salt
container in door (SIT) are fitted.
Appropriate setting: p1 = G1262,
(w/out WAW, w/out SEH, w/out
SIT).
Country setting1
Press the Tab button 39x.
The "Tab" LED flashes 3x
slowly and 9x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The "Rinse" LED is off or flashes.
The display shows pand a digit
alternately. The following
countries can be set: p1 = EUR
(Europe); p2 = AUS (Australia);
p3 = USA, p4 = JPN (Japan),
p5 = I/E (Italy/Spain), p6 = SER
(Southern Europe).3
Table 8: Service Programming Mode, G 1262
1 If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
2If the dishwasher is connected to an external ion exchanger water softener (i.e. that
needs to be regenerated with salt), the water hardness delivered by the system must be
set. If this value is unknown, set to 8°d (8.6 grains per gallon).
3The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.

Technical Information
16
G 1xxx/G 2xxx
Water Hardness [°d] Water Hardness [gpg] Display
1 1.1
P1
2 2.1
P2
3 3.2
P3
… … …
36 38.5
P36
37 – 50 39.6 – 53.5 P50
51 – 60 54.6 – 64.2 P60
61 – 70 65.3 – 74.9 P70
Table 9: Water Hardness Settings, G 1262
Rinse Aid Volume [mL]1Display
0 P0
1 P1
2 P2
3 P32
4 P4
5 P5
6 P6
Table 10: Rinse Aid Settings, G 1262
1One milliliter equals 0.3 fluid ounces.
2Standard setting.
2.4 Optima - G 1470/G 2470
Initial requirements:
1. Open the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Program button.
2. Switch on the appliance.
3. Release the Program button.
4. Immediately press the Program button 5 times; on the 5th time, hold until
the “Rinse & Hold” LED flashes.
5. Release the Program button.
6. If the “Rinse & Hold” LED does not light up, repeat the procedure.
Acknowledgement indicator:
The “Rinse & Hold” LED flashes rapidly (5 flashes per second).

Technical Information
17
G 1xxx/G 2xxx
Options:
Function Programming Display
Software version ID check Do not press the GEL
button. The “GEL” LED is
off.
The display shows the software
version ID no. in consecutive digits
(e.g., -818).
Reset
Press the GEL button
once. The “GEL” LED
flashes once quickly
intermittently. Press the
Program button to reset
all standard settings.
This programmable function can be
used to reset all modifiable
parameters to their standard
settings. The display shows pand a
digit alternately: p0 = Non-standard
settings have been made; p1 = All
settings reset to standard settings
or no modifications made.
Softener sensor activation/
Water hardness setting2
Press the GEL button 2x.
The “GEL” LED flashes 2x
quickly intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows pand the digit/s
of the set value alternately. p0 =
Softener sensor active. Hardness
setting range: p1 to p70; see Table
12.
Dispensed rinse aid
quantity setting
Press the GEL button 3x.
The “GEL” LED flashes 3x
quickly intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows P and a digit
alternately: e.g., P3 (standard
setting) indicates a dispensed
quantity of 0.1 fl.oz. (3mL). Setting
range: 0 - 0.2 fl.oz. (0 - 6 mL).
Buzzer on/off
Press GEL 4x. The “GEL”
LED flashes 4x rapidly
intermittently. Press
Program to change the
setting.
The display shows Pand a digit
alternately. Setting options: P0 =
Buzzer off; P1 = Buzzer on.
Adjust Sensor Wash
program (ID nos. -984 and
later)1
Press the GEL button 5x.
The “GEL” LED flashes 5x
quickly intermittently.
Press the Program button
as appropriate to make the
desired setting.
The display shows Pand a digit
alternately. Setting options: P0 =
Standard program cycle (factory
setting); P1 = Adjusted program
cycle. The Sensor Wash program
can be adjusted in this parameter to
deal with stubborn soiling (if
otherwise low overall soiling). If this
option is selected, the main wash
temperature is increased to 131°F
and, as a result, the program
duration is extended.
Note:
In models with software version ID –769, wait for the decimal point in the
display to switch off before pressing the GEL button.

Technical Information
18
G 1xxx/G 2xxx
Function Programming Display
Resetting standard
settings
Press the GEL button 12x.
The “GEL” LED flashes
once slowly and 2x quickly
intermittently. Press the
Program button to reset
all standard settings.
This programmable function can be
used to reset all customer-modified
parameters back to their standard
settings. The display shows Pand a
digit alternately. P0 = Settings have
been modified; P1 = All settings
reset to standard settings or no
modifications have been made.
Adjusting the main wash
temperature
(ID nos. -984 and later)
Press the GEL button 20x.
The “GEL” LED flashes 2x
slowly intermittently. Press
the Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = Wash
temperature increased. If this option
is selected, the main wash
temperature is increased and, as a
result, the program duration is
extended.
Final rinse temperature
modification (ID nos. -984
and later)
Press the GEL button 21x.
The “GEL” LED flashes 2x
slowly and once quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = Wash
temperature increased. If this option
is selected, the final rinse
temperature is increased and, as a
result, the program duration is
extended.
Program running time
reduction
(ID nos. -984 and later)
Press the GEL button 22x.
The “GEL” LED flashes 2x
slowly and 2x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = Program
running time reduction.
Temperatures are decreased and/or
hold times removed, so the program
running time is shortened.
Water quantity
normal/increased
(ID nos. -876 and later)
Press the GEL button 23x.
The “GEL” LED flashes 2x
slowly and 3x rapidly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately: p0 = Normal water
quantity (standard setting); p1 =
Increased water quantity. If p1 is
selected, approx. 16.7 fl.oz.
(500mL) more water is taken in
during each water intake cycle.
Soak activation/
deactivation
Press the GEL button 24x.
The “GEL” LED flashes 2x
slowly and 4x quickly
intermittently. Press
Program to change the
setting.
The display shows p and a digit
alternately. Options: p0 = Soak not
activated; p1 = Soak activated.
Pre-wash
activation/deactivation
Press the GEL button 25x.
The “GEL” LED flashes 2x
slowly and 5x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Pre-wash not activated; p1 =
Pre-wash activated.

Technical Information
19
G 1xxx/G 2xxx
Function Programming Display
Second interim rinse (ID
nos. -984 and later)
Press the GEL button 26x.
The “GEL” LED flashes 2x
slowly and 6x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Standard setting; p1 = With second
interim rinse.
Extended drying time
Press the GEL button 27x.
The “GEL” LED flashes 2x
slowly and 7x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options: p0 =
Normal drying time; p1 = Extended
drying time (+10 mins).
Appliance height setting2
Press the GEL button 36x.
The “GEL” LED flashes 3x
slowly and 6x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. Setting options:
p0 = Normal machine height (G
1xxx); p1 = XXL model (G 2xxx).
Model setting2
Press the GEL button 38x.
The “GEL” LED flashes 3x
slowly and 8x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows p and a digit
alternately. Setting depends on
model and whether a circulation
pump with slide shutter (WAW) and
sensor softener (SEH) are installed.
p3 = G14xx, G24xx (w/out WAW,
w/SEH).
Country setting2
Press the GEL button 39x.
The “GEL” LED flashes 3x
slowly and 9x quickly
intermittently. Press the
Program button as
appropriate to make the
desired setting.
The display shows pand a digit
alternately. The following countries
can be set: p1 = EUR (Europe); p2 =
AUS (Australia); p3 = USA; p4 =
JPN (Japan); p5 = I/E (Italy/Spain);
p6 = SER (Southern Europe).3
Table 11: Service Programming Mode, G 1470/G 2470
1 In machines with software version -876, run the update “Optimized cleaning of tea
residues in Sensor Wash program” (mat. no. 06471560). Modified threshold values will
improve the cleaning outcome.
2 If the electronic needs to be replaced during servicing, the following steps must be taken
during programming: In the first step, set the country specification and model, then switch
off the appliance. Repeat access and then set appliance width and height, and the
appropriate supply water hardness.
3The SER country specification includes the following countries: Portugal, France, the
Netherlands, Belgium and Great Britain.
Save and quit:
Switch off the appliance.

Technical Information
20
G 1xxx/G 2xxx
Water Hardness [°d] Water Hardness [gpg] Display
1 1.1
P1
2 2.1
P2
3 3.2
P3
… … …
36 38.5
P36
37 – 50 39.6 – 53.5 P50
51 – 60 54.6 – 64.2 P60
61 – 70 65.3 – 74.9 P70
Table 12: Water Hardness Settings, G 1470/G 2470
Note:
If the dishwasher is connected to an external ion exchanger water softener (i.e.
that needs to be regenerated with salt), the water hardness delivered by the
system must be set. If this value is unknown, set to 8°d (8.6 grains per gallon).
2.5 Optima - G 1472/G 2472
Initial requirements:
1. Open the door.
2. Switch off the appliance.
Accessing:
1. Press and hold the Program button.
2. Switch on the appliance.
3. Release the Program button.
4. Immediately press the Program button 5 times; on the 5th time, hold until
the “Rinse & Hold” LED flashes.
5. Release the Program button.
6. If the “Rinse & Hold” LED does not light up, repeat the procedure.
Acknowledgement indicator:
The “Rinse & Hold” LED flashes rapidly (5 flashes per second).
Options:
Function Programming Display
Software version ID check Do not press the options
button. The “Tab” LED is
off.
The display shows the software
version ID no. in consecutive digits
(e.g., -818).
Reset
Press the options button
once. The “Tab” LED
flashes once quickly
intermittently. Press the
Program button to reset
all standard settings.
This programmable function can be
used to reset all modifiable
parameters to their standard
settings. The display shows pand a
digit alternately: p0 = Non-standard
settings have been made; p1 = All
settings reset to standard settings
or no modifications made.